Land Pride RTR1550, RTR1558 manual Checking Driveline Maximum Length

Page 15

Land Pride

Table of Contents

Section 1: Assembly and Set-Up

b.Pull driveline apart into two sections as shown in Figure 1-8. Attach the outer driveline universal joint to the tractor shaft and inner driveline universal joint to the tiller gearbox shaft. Pull on each driveline section to be sure the universal joints are secured to the shafts.

c.Hold driveline sections parallel to each other to determine if they are too long. The inner and outer shields on each section should end approximately 1" short of reaching the universal joint shield on the adjacent section (see “B” dimension). If they are too long, measure 1" (“B” dimension) back from the universal joint shield and make a mark at this location on the inner and outer driveline shields.

d.Cut off inner shield at the mark (“X” dimension). Cut the same amount off the inner shaft (“X1” dimension). Repeat cut off procedure (“Y” & “Y1” dimensions) to the outer driveline half.

e.Remove all burrs and cuttings.

13588

Shortening the driveline

Figure 1-8

Checking Driveline Maximum Length

Make sure you have gone through the steps in

“Checking Driveline Minimum Length” on page 12 before checking maximum length.

Refer to Figure 1-9

The driveline maximum length must, when fully extended, have a minimum overlap of the profile tubes by not less than 1/3 the free length with both inner and outer profile tubes being of equal length.

1.Apply multi-purpose grease to the inside of the outer shaft and reassemble the driveline.

2.Assemble the two driveline profiles together with just 1/3 overlapping of the profile tubes as shown in Figure 1-9. Measure and record this overall length for checking driveline length in step 9 below.

3.Attach inner driveline yoke end to the tiller gearbox input shaft.

4.Attach outer driveline yoke end to the tractor's PTO shaft.

5.The driveline should now be moved back and forth to insure that both ends are secured to the tractor and Rotary Tiller PTO shafts. Reattach any end that is loose.

24513

Outer Shielding has been removed for clarity.

Driveline Maximum Length

Figure 1-9

IMPORTANT: A small chain is supplied with the driveline. This chain must be attached to the inner driveline shield and to the tiller to restrict shield rotation.

6.Hook driveline safety chain in the hole in the inner driveline guard. Attach the other end to the tiller’s main frame.

7.Start tractor and raise tiller just enough to remove blocks used to support the tiller frame in step 3a on page 12.

8.Slowly engage the tractor’s hydraulic 3-point to lower the Rotary Tiller. Check for sufficient drawbar clearance. Move drawbar ahead, aside or remove if required.

9.Raise and lower implement to find maximum extended driveline length. Check to make certain that the driveline overall length does not extend beyond the maximum recorded length in step 2.

7/22/08

RTR10 & RTR15 Series Rotary Tillers 311-431M

13

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Rotary Tillers Table of Contents Safety at All Times Transport Machinery Safely Important Safety InformationUse Safety Lights and Devices Practice Safe MaintenancePrepare for Emergencies Wear Protective EquipmentAvoid High Pressure Fluids Hazard 818-130C Safety Labels818-284C 818-171C818-552C 818-540C 818-543CIntroduction Using This ManualApplication Owner AssistanceTractor Requirements Assembly and Set-UpHitch Assembly Leg Stand AssemblyFront Deflector Assembly Tractor Hook-Up Rear Deflector AssemblyChecking Driveline Minimum Length Driveline InstallationChecking Driveline Maximum Length Operating Check List General Notes for Field OperationsTransporting OperatingOperating Instructions ParkingAdjustments RTR10 Tiller Hitch OffsetRTR15 Tiller Hitch Sideshift Rear Deflector Drive ChainSkid Shoe Adjustment Maintenance and Lubrication MaintenanceTine Replacement Clutches With 4 Adjusting NutsStep Plate DisassemblyPlate Assembly Clutch Disassembly & AssemblyClutches With 8 Hex Socket Bolts Shearbolt ProtectionShear Bolt and Lock Nut Part Numbers Storage Tine Replacement onHrs LubricationGearbox Bearing On Right End Of Rotor ShaftModel RTR1042 RTR1050 RTR1058 Specifications & CapacitiesRTR10 Series Rotary Tiller RTR15 Series Rotary TillerFeatures Benefits Features & BenefitsFormed and reinforced Problem Cause Solution TroubleshootingTorque Values Chart AppendixIn-tpi · m Ft-lb Mm x pitch 30 RTR10 & RTR15 Series Rotary Tillers 311-431M Warranty Overall Unit and Driveline One year Parts and LaborTines and Driveline Friction Discs Considered wear items Corporate Office P.O. Box Salina, Kansas 67402-5060 USA
Related manuals
Manual 34 pages 40 b

RTR15, RTR1558, RTR1550 specifications

Land Pride is a renowned name in the agricultural equipment industry, and their range of Rotary Tiller models, including the RTR1558, RTR1058, RTR1550, RTR1042, and RTR1542, stands out for their efficiency, robustness, and innovative design. These tillers are ideal for both commercial farmers and garden enthusiasts, offering flexible solutions for soil preparation.

The RTR1558 and RTR1550 models, designed for larger tractors, boast a heavy-duty construction and are equipped with a wide cutting width, allowing them to cover more ground in less time. This efficiency is complemented by a series of rotor knives that ensure a thorough tilling action, breaking up compacted soil while enabling better aeration and nutrient absorption. The RTR1558 features a unique gear-driven design that enhances durability and performance, making it suitable for heavy-duty applications.

For those with smaller tractors, the RTR1042 and RTR1542 models are a perfect fit. These tillers maintain a robust design while being lightweight, ensuring they can be easily maneuvered in smaller plots. With their effective rotary tilling capabilities, they help prepare seedbeds, enhance garden spaces, and efficiently mix in organic matter or fertilizers. These models also feature adjustable tilling depths, allowing users to customize the tilling process according to specific soil conditions.

The RTR1058 model, meanwhile, serves as a middle ground, delivering a balance between power and versatility. This rotary tiller’s unique design allows it to perform exceptionally well in various soil types, promoting better crop yields. Each of these tillers is equipped with a durable chain drive system that provides optimal performance and minimal downtime.

Additionally, Land Pride’s focus on user-friendly features extends to the ease of maintenance. The equipment is designed with accessible components that simplify repairs and reduce pivot point wear. Coupled with the innovative technology in their design, such as the heavy-duty frame and reinforced tines, these tillers provide long-term reliability.

In conclusion, the Land Pride RTR1558, RTR1058, RTR1550, RTR1042, and RTR1542 rotary tillers exemplify cutting-edge technology and thoughtful engineering. Their unique features make them suitable for a variety of applications, ensuring that whether you are tilling a large field or preparing a small garden, there is a Land Pride tiller that meets your needs effectively.
Top Page Image Contents