Viking viking manual Important Please Read and Follow, To Install Cabinets

Page 2

IMPORTANT - PLEASE READ AND FOLLOW

•Before beginning, please read these instructions completely and carefully.

•Do not remove permanently affixed labels, warnings, or plates from product. This may void the warranty.

•Viking outdoor stainless steel cabinets are not designed to be water tight. Water may enter cabinetry under certain conditions

•The installer should leave instructions with the consumer who should retain for future reference

NEVER use LP tanks inside any stainless steel cabinetry. Tanks must be located outside of the cabinetry at all times.

TO INSTALL CABINETS:

1. Verify cabinet product number(s) on

Illustration #1

box(es) to list of cabinets ordered.

 

2.Carefully unpack cabinets making sure not to scratch fronts. Front panels are protected by plastic coating (that must be removed after setup). Cabinets with interchangeable doors are shipped from the factory with opening from left to

5. Place cabinet(s) in approximate final position.

Illustration #3

Level cabinets using leveling legs. Use 1/2"

 

SMS screws provided to screw cabinets

 

together. (See illustration #3).

 

Install 4 Tinnerman clips (provided) before fastening cabinets together

Mount cabinets with #10 x 1/2” screws provided

right as shown (See illustration #1).

Cabinet box ready for assembly

3. In cabinets with interchangeable doors,

Illustration #2

hardware package will contain hole

 

covers and hardware to install.

 

4.Install 4 legs in the leg plates attached to bottom of each cabinet. Screw in place. (See illustration #2).

6. Determine appropriate hinge side for cabinets

Illustration #4

with interchangeable doors. Remove outside

 

door panel. Install hinges by placing plate in

 

hole in door and fasten in place with hardware

 

provided. Screw hinge plates in appropriate

 

pre-drilled holes in cabinet side. Fasten hole

 

covers with hardware provided. (See

 

Illustration #4).

 

Use #8 x 3/8” machine screw and locknut to fasten hole cover to inside door panel

7. Cabinet doors must be adjusted when cabinets are

Illustration #5

level in final position. There are two adjustment

 

screws on the hinge receiver. (See Illustration #5)

 

•The front screw is used to center the door in

 

the opening. Turning the front screws in or

 

out will center the door over the cabinet

 

opening.

 

•The back screw is used to align the front of

 

the door with the cabinet frame and secure

 

the door to the cabinet. Slightly loosen the

 

screw and slide door in or out. Retighten the

 

screw to secure the door.

 

Use #8 x 3/8” flat head M.S. and locknut to attach hinge bracket to the inside door.

Back Screw

Front Screw

2

3

Image 2
Contents Use/Installation Guide To Install Cabinets Important Please Read and FollowBack Panel Installation Care and Maintenance Warranty
Related manuals
Manual 18 pages 31.55 Kb

viking specifications

The Vikings, a seafaring people from Scandinavia, are often remembered for their raids and explorations from the late 8th to the early 11th centuries. They were not merely warriors but also traders, settlers, and skilled craftsmen. Viking society was complex, with a rich tapestry of culture, mythology, and technology that facilitated their notorious journeys across the seas.

One of the most recognizable features of the Vikings was their longships. These vessels were marvels of engineering, designed for both speed and agility. Constructed from clinker-built planks, the ships were lightweight yet sturdy, allowing them to navigate shallow rivers and venture into the open sea. The longship's shallow draft made it possible to beach the vessel for land raids, while its sleek design enabled it to travel swiftly across oceans. The sail, often made of wool, could be raised or lowered depending on the wind conditions, showcasing the Vikings' adaptability at sea.

The Vikings were also known for their advanced technological skills, particularly in metalworking and woodworking. They forged high-quality weapons, including swords and axes, often inlaid with intricate designs that demonstrated their craftsmanship. Additionally, they utilized various tools for farming, shipbuilding, and everyday life, which contributed to their survival and success as both raiders and settlers.

In matters of trade, the Vikings established extensive networks across Europe, the Middle East, and Asia. They exchanged goods such as fur, amber, and slaves for silver, silk, and spices. Their trade routes connected them to distant cultures, resulting in a vibrant exchange of ideas, technologies, and goods.

Socially, Viking society was structured around clans and chieftains, with a warrior ethos that emphasized bravery and loyalty. They celebrated their gods and heroes through oral traditions, passing down sagas and myths that celebrated their history and cultural identity.

Viking settlements were established in places like Iceland, Greenland, and even North America, demonstrating their adventurous spirit and willingness to explore new lands. These outposts often included longhouses built from timber and sod, designed to withstand harsh weather conditions.

Overall, the legacy of the Vikings endures as a testament to their resilience, ingenuity, and the profound impact they had on the world during their era. Their blend of fearsome reputation and remarkable achievements continues to captivate audiences to this day.