Bowens QuadX 3000 operating instructions Table of Contents

Page 3

8.0Warnings

WARNINGS & FAULT FINDING

If the unit appears to have developed a fault, first establish that it is a genuine internal fault and not a case of normal operation such as overheat. Carry out the following checks to eliminate any external causes. If no obvious problem can be found and replacement of the modelling lamp, flash tube or fuse does not effect a cure then it is likely that an internal fault has developed. Always return the unit to an authorised service centre if a fault is suspected after these checks. UNDER NO CIRCUMSTANCES SHOULD YOU ATTEMPT ANY REPAIR yourself.

Flash/Misfire Warning

Following a flash, the unit will temporarily display READY on the red numeric displays for 5 seconds. This serves as a convenient method of showing correct pack operation when two or more packs are running flashing together. If the unit receives a trigger signal from any of the valid sources (TEST, IR REMOTE, IR TRIGGER, SYNC) but fails to flash for any reason then the red numeric will display “headfail”. Press ⇐ to clear the message. Increase the power setting to maximum and use the TEST button to try and flash again. If the problem continues to happen on more than the odd occasion, particularly at lower power settings, then it is likely that the flash head tube is wearing out. Before replacing the tube, check that the trigger wire is correctly connected and is not shorted to or in close proximity to the metal reflector. If the unit fails to flash at all then check the flash tube for signs of damage or overheating.

If the unit fails to flash and the display warning is not given then the Sync. lead and/or camera should be suspected. If possible check these with another flash system. Check the polarity of the Sync. from the camera and use an adapter to reverse it if necessary. The QuadX 3000 supplies a SYNC. voltage of +5V with respect to the chassis Ground.

OVERHEAT Warning

The unit is fitted with overheat protection that inhibits charging until the unit has cooled sufficiently. The display flashes the READY LED and displays a warning message on the LCD while the overheat condition exists. Overheat will normally only occur if the unit is flashed repeatedly at a fast repetition rate. Slowing down the repetition rate will normally help keep the unit out of overheat. Dimming the modelling lamp or turning it off may also help.

NOTE: The controls are inhibited during overheat to prevent inadvertent changes being made. The overheat condition remains until the pack reaches a target lower temperature or is turned off and then on after the pack has cooled by a few degrees.

The Control Panel Does Not Light

If the control panel does not light when the unit is switched on then first check that the AC power supply to the unit is OK and that the thermal resets buttons on the rear are set. Under exceptional conditions of use the internal fuse may blow. This is normal and is designed to protect the unit. Report the problem to your local service agent. Do not attempt to locate and replace the internal fuse.

The Control Panel Lights but Does Not come To ‘READY’

If this happens then first confirm that the AC power supply is adequate and within the prescribed limits. Try switching the unit off, wait a minute, and then switch on again.

TABLE OF CONTENTS

1.0QuadX 3000 Control Guide

2.0QuadX 3000 Function Overview

3.0Getting Started

4.0Menu System Overview

5.0The Information Menu

6.0The Main Selection Menu

7.0Advanced Options Menu

8.0Warnings

9.0Specification

Page 2 Page 4
Image 3
Page 2 Page 4
Contents Quadx Introduction AccessoriesTable of Contents QuadX 3000 Control Guide Advanced Options ⇒ Setup Flash Mode ⇒ Multi Trigger Advanced Options ⇒ Reset Job CounterFlash Counter Menu Advanced Options ⇒ Setup Flash Mode ⇒ Trigger Skip Flash PowerModelling Power Setup Flash ModeAdvanced Options ⇒ Charge Control Time Out SettingSave/Recall Setup Advanced Options ⇒ BrightnessAdvanced Options ⇒ Alternate Units Advanced Options ⇒ Speaker SetupSet IR Channel Bracketing Mode ExampleInformation Menu List Main Selection Menu Speaker On/OffBracketing Cont ModellingModelling IR CHAN=ALL S/W

QuadX 3000 specifications

The Bowens QuadX 3000 is a cutting-edge lighting solution designed for professional photographers and videographers seeking versatility and performance. This innovative lighting system boasts a host of features, technologies, and characteristics that make it an essential tool for achieving outstanding results in various shooting environments.

At the heart of the QuadX 3000 is its impressive 3000 watt-second output, delivering consistent and powerful bursts of light. This high output allows photographers to capture images with exceptional detail and dynamic range, even in challenging lighting conditions. The unit is designed to offer a fast recycle time, enabling users to shoot continuously without delay, making it suitable for fast-paced environments such as events or action shoots.

One of the standout features of the QuadX 3000 is its advanced modeling light technology. The system offers adjustable modeling lights that allow users to visualize their lighting setup effectively before taking the shot. This feature helps photographers to fine-tune their lighting angles and intensities, resulting in more accurate and creative compositions. The modeling lights also double as continuous lights, making this system a versatile choice for both video and photography.

Portability and ease of use are also key characteristics of the Bowens QuadX 3000. It incorporates a compact design and a lightweight aluminum body, ensuring that the system can be transported easily to various locations. The unit is equipped with an intuitive user interface that provides quick access to settings and adjustments, allowing photographers to focus on their creative process instead of struggling with complicated machinery.

Additionally, the QuadX 3000 is compatible with an extensive range of light modifiers, such as softboxes, umbrellas, and grids, allowing users to shape and control their light sources to suit their specific needs. This compatibility enhances the creative possibilities for photographers and videographers, enabling them to achieve the perfect lighting effect for each shot.

In terms of reliability, the Bowens QuadX 3000 features robust internal components and a cooling system that prevents overheating during extended use. This ensures that the lighting system maintains performance without the risk of malfunction, making it a trusted choice for professionals.

In summary, the Bowens QuadX 3000 combines powerful output, advanced modeling light technology, portability, user-friendly design, and compatibility with various light modifiers to create a versatile lighting solution for photographers and videographers. Its reliability and innovative features make it a standout choice for those who demand excellence in their lighting equipment.
Top Page Image Contents