Crown’s Three-Year, No-Fault, Full Warranty

CT-1610

channel that flashes to show distortion if a channel’s output waveform differs from its input by 0.05% or more.

ODEP: A green front-panel LED for each channel that shows thermal-dynamic energy reserve. Normally, each ODEP indicator is lit to show available reserve energy. In the rare event that a channel has no reserve, its indicator will dim in proportion to ODEP limiting.

Input/Output

Input Connectors: Balanced three-terminal barrier block connectors with test points are provided on the factory-installedPIP2-BB module.

Input Impedance: Nominally 20 k ohms, balanced. Nominally 10 k ohms, unbalanced.

Input Sensitivity: Settings include 0.775 volts (8/4-ohm) or 0.775 volts (70-V) for standard 1 kHz power, or a 26 dB voltage gain.

Maximum Input Level: 9 Vrms.

Output Connectors: A back-panel barrier block with two terminal connections for each output channel.

Output Impedance: Less than 10 milliohms in series with less than 2 microhenries.

DC Output Offset: Less than ±10 millivolts.

RSVP: A back panel RJ-11 modular connector interfaces with an R.S.V.P. unit to provide remote control of amplifier power on/off functions.

Output Signal:

Stereo: Unbalanced, two-channel.

Bridge-Mono:Balanced, single-channel. Channel 1 controls are active; Channel 2 controls should be turned down.

Parallel-Mono: Unbalanced, single-channel. Channel 1 controls are active; Channel 2 is bypassed.

Protection

Com-Tech amplifiers are protected against shorted, open or mismatched loads; over- loaded power supplies; excessive temperature; chain destruction phenomena; input overload damage; and high-frequency blowups. They also protect loudspeakers from input/output DC and turn-on/turn-off transients.

If unreasonable operating conditions occur, the patented ODEP circuitry will proportionally limit the drive level to protect the output transistor stages, particularly in the case of elevated temperature. Transformer overheating will result in a temporary shutdown of both channels; the transformer will automatically resets itself when it has cooled to a safe

temperature. Controlled slew rate voltage amplifiers protect against RF burnouts. And input overload protection is provided by current-limiting resistance at the input.

Turn On: The four-second turn-on delay prevents dangerous turn-on transients. “Soft start” circuitry provides low inrush so power sequencers are rarely needed with multiple units.

Accessories: Crown PIP and PIP2 modules including IQ-PIP modules; R.S.V.P.

Construction

Steel chassis with durable black powder-coat finish, front panel Lexan overlay, and specially- designed flow-through ventilation from front to side panels.

Cooling: Internal heat exchangers with on- demand, forced-air cooling.

Dimensions: 19-inch (48.3-cm) standard rack mount width (EIA RS-310-B), 7.0-inch (17.8- cm) height, 16-inch (40.6-cm) depth behind mounting surface and 0.25 inches (0.6 cm) in front of mounting surface.

Approximate Weight: Center of gravity is 6 inches (15.2 cm) behind the front mounting surface. 57 pounds, 14 ounces (26.3 kg) net; 66 pounds, 10 ounces (30.2 kg) shipping weight.

Crown’s Three-Year, No-Fault, Full Warranty

Crown offers a Three-Year, No-Fault, Full Warranty for every new Crown amplifier—an unsur- passed industry standard. With this unprecedented No-Fault protection, your new Crown amplifier is warranted to meet or exceed original specifications for the first three years of ownership. During this time, if your amplifier fails, or does not perform to original specifica- tions, it will be repaired or replaced at our expense. About the only things not covered by this warranty are those losses normally covered by insurance and those caused by intentional abuse. And the coverage is transferable, should you sell your amplifier.

See your authorized Crown dealer for full warranty disclosure and details. For customers outside of the USA, please contact your authorized Crown distributor for warranty information or call 219-294-8200.

Crown International, Inc.

P.O. Box 1000

Elkhart, IN 46515-1000

TEL: 219-294-8200

FAX: 219-294-8FAX

www.crownaudio.com

Specifications subject to change without prior notice.

Crown, Com-Tech, IOC and ODEP are registered trademarks, and Ground Bridge, PIP and PIP2 are trademarks of Crown International, Inc. Printed in U.S.A.

08/00	128422-1

CT-1610 specifications

The Crown Audio CT-1610 is a versatile power amplifier designed to deliver high-quality audio performance in various applications, ranging from live sound reinforcement to fixed installations. Renowned for its reliability and exceptional sound fidelity, the CT-1610 is an ideal choice for professionals in the audio industry.

One of the standout features of the CT-1610 is its robust power output. The amplifier provides up to 1600 watts of power at 4 ohms, ensuring that it can drive even the most demanding speakers with ease. This capability makes it well-suited for large venues, concerts, and events where high sound levels are required. Additionally, the amplifier can operate at 8 ohms, offering flexibility in matching to different speaker configurations.

The CT-1610 incorporates Crown's proprietary Class-I technology, which combines efficiency with superior audio performance. This design minimizes heat generation, allowing the amplifier to run cooler and more quietly than traditional class amplifiers. This is particularly beneficial in environments where prolonged use is common, as it enhances both durability and longevity.

Another notable characteristic of the CT-1610 is its extensive protection circuitry. The amplifier is equipped with advanced thermal protection, short circuit protection, and overload protection, ensuring that it remains safe under challenging operating conditions. These features contribute to the amplifier's reputation for reliability, making it a trusted choice for professionals.

In terms of connectivity, the Crown CT-1610 offers a variety of options. It features balanced XLR inputs and integrated speakON outputs, providing seamless integration with other audio components and ensuring a low-noise signal path. This versatility allows for straightforward setup and operation, catering to users of all experience levels.

Furthermore, the CT-1610 boasts a lightweight and compact design, which is a significant advantage for mobile applications. Weighing in at under 25 pounds, it is easy to transport and install, without compromising on performance.

Overall, the Crown Audio CT-1610 stands out with its powerful output, innovative technology, and robust build quality, making it an exceptional choice for audio professionals seeking reliable, high-performance amplification.