To Remove Wheels See Fig | Poulan PP10530ES specification

SERVICE AND ADJUSTMENTS

WARNING: Belt replacement requires separation of the snow thrower. While separating the auger housing from the frame assembly, it is important that an assistant stand in the operating position and hold the snow thrower handles. Se- rious personal injury and/or damage to the unit could occur if the snow thrower should fall during the belt changing process.

FRAME	AUGER
ASSEMBLY	HOUSING

HANDLES

1.REMOVE GASOLINE FROM FUEL TANK - Drain gaso- line from fuel tank into a suitable container, outdoors, away from ﬁre or ﬂame. Wipe up any spilled gasoline.

2.REMOVE DISCHARGE CHUTE - Loosen locknut securing chute rotator head to mounting bracket only enough to allow chute rotator head to be raised and discharge chute to be removed from snow thrower.

3.REMOVE BELT COVER - See “TO REMOVE BELT COVER” in this section of this manual.

4.REMOVE ENGINE PULLEY - Remove bolt, lockwasher and ﬂat washer securing pulley to engine crankshaft. Remove outside (auger) pulley only from crankshaft.

5.SEPARATE SNOW THROWER - With your assistant standing in the operating position holding the handles, remove the two (2) bolts and lock washers holding auger housing and frame together.

WARNING: As the last bolt is removed, have your assistant carefully lower the handles down to the ground.

6.REMOVE AUGER BELT from around pulley.

7.RELIEVETENSIONONTRACTIONDRIVEBELTIDLER and remove traction drive belt from around pulleys.

HINT: Insert a 3/8" drive ratchet (in the “ON” position) into the square hole in idler arm and rotate ratchet clockwise to relieve tension.

8.With tension relieved on idler, install new traction drive belt around pulleys and inside belt keepers.

9.Place auger belt around and inside the groove of auger pulley only.

10.While your assistant slowly raises handles to rejoin the auger housing and frame assembly, pull up on the auger belt and squeeze sides together above pulley so belt is fully seated in groove of pulley.

11.Bring snow thrower completely together and check carefully for proper routing of belts. If auger belt has become dislodged from the pulley (by catching the idler arm bracket while bringing snow thrower together), separate the snow thrower and repeat step 10. Belt

must be fully seated in pulley groove when bringing
the snow thrower together.	17

12.Install the two (2) hex bolts and lock washers and tighten securely.

13.INSTALL ENGINE PULLEY - Place belt in pulley groove and slide pulley on crankshaft. Install ﬂat washer, lock- washer and bolt and tighten securely (30-35 ft. lbs. torque). Make sure belt is inside belt keeper.

14.INSTALL BELT COVER and two (2) screws. Tighten securely.

15.INSTALL DISCHARGE CHUTE – See “INSTALL DIS- CHARGE CHUTE / CHUTE ROTATER HEAD” in the Assembly / Pre-Operation section of this manual.

	BELT KEEPER
	TRACTION DRIVE BELT
	ENGINE	FLAT WASHER
	PULLEY	FLAT WASHER
	PULLEY
		LOCKWASHER
		BOLT
IDLER ARM			AUGER
SQUARE			BELT
HOLE
CLUTCHING
IDLER ARM
BRACKET
	AUGER PULLEY
		BOLT	LOCK
			WASHER
FRAME	AUGER
FRAME	HOUSING

FIG. 23

TO REMOVE WHEELS (See Fig. 24)

•Remove the klik pin and remove wheel from axle.

IMPORTANT: When installing wheel, be sure to use the axle hole closest to the end of the shaft – do not use the hole in the wheel hub (if equipped). Inner hole in axle and hole in wheel hub are not used for your model snow thrower.

NOTE: To seal punctures or prevent ﬂat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

KLIK PIN (INSTALL	OUTER HOLE
IN OUTER HOLE
OF AXLE ONLY)

AXLE

WHEEL

WHEEL HUB

FIG. 24

PP10530ES specifications

The Poulan PP10530ES is a versatile and powerful tool designed for homeowners and landscaping professionals alike. This gas-powered chainsaw combines efficiency, ease of use, and innovative technology, making it a go-to choice for various cutting tasks.

At its heart, the PP10530ES is equipped with a robust 30cc engine that delivers ample power for cutting through wood of varying thicknesses. The engine is designed with advanced engineering, ensuring reliable performance while maintaining a lightweight profile that reduces operator fatigue during prolonged use.

One of the standout features of the Poulan PP10530ES is its Easy Start technology. This user-friendly feature significantly reduces the effort required to get the chainsaw up and running. With a simple pull of the starter cord, users can achieve a quick and hassle-free start, minimizing the frustration often associated with chainsaws.

The chainsaw also boasts an innovative automatic oiler system, ensuring that the bar and chain receive a consistent supply of lubrication during operation. This feature not only enhances the overall performance but also prolongs the life of the cutting components, providing long-lasting durability.

Safety is a top priority in the design of the PP10530ES. It is equipped with a chain brake that offers added protection by stopping the chain quickly in the event of kickback, an inherent risk in chainsaw operation. Furthermore, the comfortable grip handle and lightweight body enhance control and maneuverability, making it easier for users to handle during various cutting tasks.

A 14-inch bar length provides an impressive cutting capacity, enabling users to tackle a range of projects from trimming branches to felling small trees. The chainsaw's compact design allows for precise cuts and easy access to tight spaces, making it ideal for both professional landscapers and DIY enthusiasts.

In conclusion, the Poulan PP10530ES chainsaw stands out for its combination of power, efficiency, and safety features. With its easy-start mechanism, automatic oiler, and ergonomic design, it delivers a seamless cutting experience, ensuring that users can complete their tasks with confidence and ease. Whether you're clearing brush or performing routine yard maintenance, the PP10530ES is a reliable tool that won't disappoint.