Poulan 96192003801, 436001 owner manual Unfold Upper Handle, Install Speed Control ROD See Figs

Page 5

ASSEMBLY / PRE-OPERATION

NOTE: The multi-wrench may be used for assembly of the chute rotator head to snow thrower and making adjustments to the skid plates.

UNFOLD UPPER HANDLE

1.Raise upper handle to the operating position and tighten handle knobs securely. Additional carriage bolts, washers and handle knobs are in bag of parts. Use to secure upper handle to lower handle. Install in lower holes in handles.

INSTALL SPEED CONTROL ROD (See Figs. 1 and 2)

1.Remove plastic tie securing rod to lower handle.

2.Insert rod into speed control bracket and secure with retainer spring.

SPEED

CONTROL

ROD

PLASTIC TIE

UPPER

HANDLE

HANDLE

KNOB

LOWER

HANDLE

FIG. 1

SPEED CONTROL ROD
	RETAINER
	SPRING
SPEED	SPEED
CONTROL	CONTROL
BRACKET	LEVER

FIG. 2

INSTALL TRACTION DRIVE CONTROL ROD (See Figs. 3 and 4)

The traction drive control rod is installed on the snow thrower.

1.Remove plastic tie securing rod to lower handle.

2.With top end of rod positioned under left side of control panel, push rod down and insert top end of rod into hole in drive control bracket. Secure with retainer spring.

PLASTIC TIE

TRACTION DRIVE

CONTROL ROD

VINYL

SLEEVE

FIG. 3

TRACTION DRIVE	RETAINER
CONTROL LEVER	SPRING
	TRACTION
	DRIVE
	CONTROL
	ROD
DRIVE
CONTROL
BRACKET

FIG. 4

5

Image 5

Contents Snow Thrower Model NumberSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents HOW to SET UP Your Snow Thrower Assembly / PRE-OPERATIONParts Packed Separately in Carton Remove Snow Thrower from CartonUnfold Upper Handle Install Speed Control ROD See FigsInstall Traction Drive Control ROD See Figs Check Tire Pressure Install Auger Control ROD See FigsInstall Discharge Chute / Chute Rotater Head See Fig Know Your Snow Thrower OperationPrimer Ignition KEYElectric start button used for starting the engine Meets A.N.S.I. Safety RequirementsStopping HOW to USE Your Snow ThrowerTo USE Fuel SHUT-OFF Valve See Fig To USE Choke Control See FigTo Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigTo Throw Snow See Fig Before Starting the Engine To Start Engine Snow Throwing TipsBefore Stopping If Recoil Starter has FrozenGeneral Recommendations MaintenanceBefore Each USE LubricationEngine CleaningTo Adjust Snow Thrower Height Service and AdjustmentsChute Deflector Shear Bolts See FigTo Replace Belts See Fig To Remove Wheels See Fig To Adjust Cable Tension See FigCarburetor Engine SpeedOther StorageFuel System Engine OILTroubleshooting Exploded KEY Part Description Scraper BAR Auger HousingAuger 27 LH Auger 27 RHBearing Plug Auger BearingSkid Plate LH Skid Plate RHPOP Rivet Knob BlackWasher Plastic WasherCable Assembly Adjustable LEVER/CABLE Rotator AssemblyCable Assembly Heat Shield Rotator HeadHandle Grip 196944X431 Panel Bracket LH 196943X431 Panel Bracket RHLower Handle Pivot Support WeldmentRetainer SpacerKnob RED Handle KnobTraction ROD Impeller RODShifter ROD TOP Shifter ROD BottomConsole Panel Wire HarnessHeadlight Bezel Flood HeadlightRepair Parts Snow Thrower - Model Number PR627ES Drive Drive Plate Assembly Speed Selector AssemblyWheel HUB END PlateAxle Shaft 01.03.005-BRoll PIN 3/16 SprocketFrame Complete LCT Engine427963X421 Engine Mounting PlateTraction Belt Impeller BeltIdler ARM Bracket Idler Pulley432332X428 Wheel Assembly LH432331X428 422663 Safety Ignition KEYDECAL, Danger 181037Service Notes Service Notes Limited Warranty