Poulan 96198003600 Service and Adjustments, To Adjust Snow Thrower Height, Chute Deflector

Page 16

SERVICE AND ADJUSTMENTS

WARNING:Toavoidseriousinjury,before performing any service or adjustments:

1. Be sure the on/off switch is in the OFF position.

2.Remove safety ignition key.

3.Make sure the augers and all moving parts have completely stopped.

4.Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug.

SNOW THROWER

TO ADJUST SNOW THROWER HEIGHT

See “TO ADJUST SKID PLATES” and “SCRAPER BAR” in the Operation section of this manual.

CHUTE DEFLECTOR

Thechutedeflector,attachedtothetopofthedischargechute, is provided to direct discharging snow away from the opera- tor. If the deflector becomes damaged, it should be replaced.

WARNING: To avoid serious injury, never operate your snow thrower with the deflector removed or damaged.

•To change direction and/or distance snow is discharged, see “TO CONTROL SNOW DISCHARGE” in the Op- eration section of this manual.

SHEAR BOLTS (See Fig. 19)

AUGER SHEAR BOLTS

Both right and left-hand augers are secured to the auger shaft with a shear bolt and hex nut. Should a foreign ob- ject or ice become lodged in the augers, the shear bolts are designed to break, preventing damage to any other components. If one or both augers do not turn when auger control lever is engaged, check to see if one or both of the bolts have sheared. To replace the shear bolts:

1.Disengage all controls and move throttle control to STOP position. Wait for all moving parts to stop.

2.Remove safety ignition key and disconnect spark plug wire from spark plug. Place wire where it cannot come in contact with spark plug.

3.Align hole in auger hub with hole in auger shaft and install a new 1/4-20 x 2" shear bolt. Install 1/4-20 lock nut and tighten securely.

CAUTION: Do not substitute. Use only original equipment shear bolts as supplied with your snow thrower.

4.Insert safety ignition key and reconnect spark plug wire to spark plug.

IMPELLER SHEAR BOLTS

The impeller is secured to the impeller shaft with two (2) capscrew/shear bolts and hex nuts. Should a foreign object or ice become lodged in the impeller, the capscrews are designed to break, preventing damage to any other com- ponents. If impeller does not turn when auger control lever is engaged, check to see if the capscrews have sheared.

To replace the capscrew/shear bolts:

1.Disengage all controls and move throttle control to STOP position. Wait for all moving parts to stop.

2.Remove safety ignition key and disconnect spark plug wire from spark plug. Place wire where it cannot come in contact with spark plug.

3.Align holes in impeller hub with holes in impeller shaft and install two (2) new 1/4-20 x 1-5/8" capscrew/shear bolts. Install 1/4-20 locknuts and tighten securely.

CAUTION: Do not substitute. Use only original equipment capscrew/shear bolts as supplied with your snow thrower.

4.Insert safety ignition key and reconnect spark plug wire to spark plug.

1/4-20

1/4-20 x 1-5/8

1/4-20 x 2

LOCKNUT

CAPSCREW /

SHOULDER /

 

SHEAR BOLT

SHEAR BOLT

 

IMPELLER HUB

 

 

IMPELLER

 

 

SHAFT

 

 

 

AUGER

 

 

HUB

1/4-20

 

 

LOCKNUT

AUGER HUB

AUGER SHAFT

Fig. 19

TO REMOVE BELT COVER (See Fig. 20)

1.Remove the two (2) screws securing belt cover to frame.

2.Remove belt cover.

3.Replace belt cover by installing cover and screws and tighten securely.

BELT

COVER

FRAME

SCREWS

Fig. 20

16

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Model Number Snow ThrowerSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Assembly / PRE-OPERATION HOW to SET UP Your Snow ThrowerParts Packed Separately in Carton Remove Snow Thrower from CartonInstall Traction Drive Control ROD See Figs Install Speed Control ROD See FigsUnfold Upper Handle Install Auger Control ROD See Figs Install Discharge Chute / Chute Rotator Head See FigInstall Chute Deflector Remote Control See Figs Check Tire PressureOperation Know Your Snow ThrowerPrimer Ignition KEYMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting the engineHOW to USE Your Snow Thrower StoppingTo USE Fuel SHUT-OFF Valve See Fig To USE Choke Control See FigTo Throw Snow See Fig Using the CLEAN-OUT Tool See FigTo Move Forward and Backward See Fig To Adjust Skid Plates See Fig Before Starting the EngineScraper BAR See Fig Check Engine OIL Level See FigSnow Throwing Tips To Start EngineBefore Stopping If Recoil Starter has FrozenMaintenance General RecommendationsBefore Each USE LubricationCleaning EngineService and Adjustments To Adjust Snow Thrower HeightChute Deflector Shear Bolts See FigTo Replace Belts See Fig To Adjust Cable Tension See Fig To Remove Wheels See FigCarburetor Engine SpeedStorage OtherFuel System Engine OILTroubleshooting Auger Housing KEY Part DescriptionScraper BAR Auger 27 LHExploded Gearbox Assembly 178675X008 Corner Bracket Clean OUT ToolBearing Impeller PulleyAuger Bearing Bearing PlugSkid Plate LH Skid Plate RHKnob Black POP RivetChute Snow Shield Shield Retainer StrapLEVER/CABLE Rotator Assembly Cable Assembly AdjustableCable Assembly Heat Shield Rotator HeadLoop Handle LH Loop Handle RHLower Tube Pivot Support01.08.002-F Impeller ROD Traction RODWire Harness Console PanelHeadlight Bezel Flood Headlight01.03.005-B Exploded Speed Selector Assembly Drive Plate AssemblyWheel HUB END PlateComplete LCT Engine Frame427963X428 Engine Mounting PlateImpeller Belt Traction BeltIdler ARM Bracket Idler Pulley432335X421 Wheel Assembly LH432336X421 Safety Ignition KEY 422663181037 DECAL, DangerDECAL, DANGER, Deflector DECAL, InstructionService Notes Limited Warranty

PP291E27, 96198003600, 435564 specifications

The Poulan PP291E27 is a powerful and efficient string trimmer designed for both residential and light commercial use. With its robust engine and user-friendly features, it delivers exceptional performance for various trimming and edging tasks, making it a popular choice for homeowners and landscapers alike.

One of the standout features of the PP291E27 is its 29cc 2-cycle engine, which provides the power needed to tackle thick grass and weeds. This engine is designed for efficiency, ensuring that you can complete jobs quickly without sacrificing performance. The trimmer is also equipped with an Easy Start system, which simplifies the starting process, allowing users to get to work with minimal effort.

The PP291E27 also boasts a versatile cutting width of 17 inches, making it suitable for trimming in tight spaces as well as larger areas. The dual-line feed head allows for easy line replacement and ensures an even cut, while the bump feed mechanism makes it easy to extend the cutting line as you work, promoting efficiency.

Weight is another important factor for string trimmers, and the PP291E27 is designed to be lightweight, which enhances maneuverability during use. The ergonomic handle provides comfort and reduces fatigue, allowing you to work for longer periods without strain. Additionally, the trimmer features an adjustable handle, making it customizable for users of different heights.

For durability, the PP291E27 features a solid construction that can withstand the rigors of outdoor use. The high-quality materials used in its design ensure that it can endure tough conditions, making it a reliable tool in any landscaping arsenal.

In terms of technology, Poulan has incorporated advanced features to minimize emissions, aligning with environmental standards while promoting cleaner operation. This eco-friendly approach is increasingly important for modern gardeners and landscapers who are conscious about their environmental footprint.

Overall, the Poulan PP291E27 is a versatile, powerful, and user-friendly string trimmer that combines efficiency with ergonomic design. Whether you're maintaining a home lawn or managing landscape projects, this trimmer stands out as a dependable choice for achieving a well-groomed landscape. With its balance of power, lightweight design, and ease of use, the PP291E27 continues to be a preferred option in the competitive market of outdoor power equipment.
Top Page Image Contents