Poulan 406281, 96192001400 owner manual Repair Parts Snow Thrower Model PP11H30ES Handles

Page 25

REPAIR PARTS SNOW THROWER - MODEL PP11H30ES (96192001400)

HANDLES

KEY

PART

 

NO.

NO.

DESCRIPTION

1405999X479 Lever, Auger Control, RH

2405783X479 Lever, Traction Drive Control, LH

4

178888

Bushing, Flange

5

169675

Retainer, Hairpin

6

17060408

Screw, Hex Head 1/4-20 x 3/4

7

178652

Rod, Interlock

8196333X008 Arm, Impeller Rod

9196334X008 Arm, Traction Rod

10196619X479 Panel, Control

1174780524 Screw, Hex Head 5/16-18 x 1-1/2

1274780528 Screw, Hex Head 5/16-18 x 1-3/4

13407856X479 Handle Tube, LH

14407857X479 Handle Tube, RH

15751153 Nut, Lock 5/16-18

1619131316 Washer, Flat 3/8

17

178899

Knob, Handle

18

193433

Rod, Auger Control

19

179098

Rod, Traction Control

20

180428

Rod, Auger Control

2173350500 Nut, Hex, Jam 5/16-18

2272120618 Bolt, Carriage 3/8-16 x 2-1/4

23178643X479 Handle Tube, Lower

24

192091

Sleeve, Spring

25

180926

Spring, Traction Drive

26

178669

Spring, Auger Control

2717000616 Screw, Hex Head 3/8-16 x 1

28198559 Bushing, Pivot Lever

30 182906

Console, Panel

31175262 Screw, Hex Head, Tapping #10-24 x 1-1/4

32184471 Screw, Hex Head, Tapping #10-24 x 1/2

33196335X008 Latch, Interlock

34

183518

Bolt, Shoulder

35

68038

Nut, Lock 1/4-20

36

178831

Spring, Torsion, Lever

37

193885

Spring, Interlock

38

178666

Headlight, Halogen (Includes Bulb)

- -

401620

Bulb, Halogen

39

178668

Bezel, Headlight

40

180964

Harness, Headlight (Halogen)

42196336X008 Lever, Interlock

43196337 Rod, Latch, Interlock

44

196338

Rod, Arm, Interlock

45

700279

Clip

46

57079

Washer, Hardened

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. 25

Image 25
Contents Snow Thrower Model NumberSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton HOW to SET UP Your Snow Thrower Assembly / PRE-OPERATIONRemove Snow Thrower from Carton Unfold Upper HandleInstall Auger Control ROD See Figs Install Traction Drive Control ROD See FigsInstall Chute Deflector Remote Control See Figs Install Discharge Chute / Chute Rotator Head See FigCheck Tire Pressure Know Your Snow Thrower OperationDeflector remote control lever used to change Meets A.N.S.I. Safety RequirementsStopping HOW to USE Your Snow ThrowerPower Steering Operation See Fig Using the CLEAN-OUT Tool See FigTo Adjust Skid Plates See Fig To Move Forward and Backward See FigScraper BAR Before Starting the EngineTo Start Engine Before Stopping Snow Throwing TipsIf Recoil Starter has Frozen Maintenance Engine CleaningTo Adjust Snow Thrower Height Service and AdjustmentsChute Deflector Remove the klik pin and remove wheel from axle To Remove Wheels See FigOther StorageTroubleshooting Page KEY Part Description Page 183334 Knob, Lever Repair Parts Snow Thrower Model PP11H30ES Handles Repair Parts Snow Thrower Model PP11H30ES Handles Repair Parts Snow Thrower Model PP11H30ES Drive Repair Parts Snow Thrower Model PP11H30ES Drive Page KEY Part Description Repair Parts Snow Thrower Model PP11H30ES Wheels / Decals Repair Parts Limited Warranty