Poulan 422075, 96192002302 HOW to SET UP Your Snow Thrower, Tool BOX See Fig, Unfold Upper Handle

Page 5

ASSEMBLY / PRE-OPERATION

HOW TO SET UP YOUR SNOW THROWER

TOOL BOX (See Fig. 8)

A toolbox is provided on your snow thrower. The toolbox is located on top of the belt cover. Store the extra shear bolts, nuts and multi-wrench provided in parts bag in the toolbox.

NOTE: The multi-wrench may be used for assembly of the chute rotator head to snow thrower and making adjustments to the skid plates.

UNFOLD UPPER HANDLE

1.Raise upper handle to the operating position and tighten handle knobs securely. Additional carriage bolts, washers and handle knobs are in bag of parts. Use to secure upper handle to lower handle. Install in lower holes in handles.

SPEED

CONTROL

ROD

PLASTIC TIE

UPPER

HANDLE

HANDLE

KNOB

LOWER

HANDLE

FIG. 1

SPEED CONTROL ROD
		RETAINER
		SPRING
SPEED		SPEED
CONTROL	CONTROL
BRACKET		LEVER
FIG. 2		5

INSTALL SPEED CONTROL ROD (See Figs. 1 and 2)

1.Remove plastic tie securing rod to lower handle.

2.Insert rod into speed control bracket and secure with retainer spring.

INSTALL TRACTION DRIVE CONTROL ROD (See Figs. 3 and 4)

The traction drive control rod has the long loop on the end of the spring as shown.

1.Slide rubber sleeve up rod and hook end of spring into pivot bracket with loop opening down as shown.

2.With top end of rod positioned under left side of control panel, push rod down and insert top end of rod into hole in drive control bracket. Secure with retainer spring.

TRACTION DRIVE

CONTROL ROD

RUBBER

SLEEVE

LOOP OPEN-

ING DOWN

PIVOT

BRACKET

FIG. 3

TRACTION DRIVE	RETAINER
CONTROL LEVER	SPRING
	TRACTION
	DRIVE
	CONTROL
	ROD
DRIVE
CONTROL
BRACKET

FIG. 4

Image 5

Contents Snow Thrower Model NumberSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Remove Snow Thrower from Carton Assembly / PRE-OPERATIONParts Packed Separately in Carton Install Speed Control ROD See Figs HOW to SET UP Your Snow ThrowerInstall Traction Drive Control ROD See Figs Tool BOX See FigCheck Tire Pressure Install Auger Control ROD See FigsInstall Discharge Chute / Chute Rotater Head See Fig Know Your Snow Thrower OperationPrimer Ignition KEYRecoil auxiliary starter handle used for starting the engine Meets A.N.S.I. Safety RequirementsStopping HOW to USE Your Snow ThrowerTo Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigTo Throw Snow See Fig To Start Engine Before Starting the EngineIf Recoil Starter has Frozen Snow Throwing TipsBefore Stopping General Recommendations MaintenanceBefore Each USE LubricationEngine CleaningTo Adjust Snow Thrower Height Service and AdjustmentsChute Deflector Shear Bolts See FigTo Replace Belts See Fig Other StorageTroubleshooting Service Notes Exploded KEY Part Description Scraper BAR Auger HousingAuger 27 LH Auger 27 RHBearing Plug Auger BearingDeflector Weldment Chute WeldmentDeflector Seal StrapRotator Head LEVER/CABLE Rotator AssemblyRotator Pivot Bracket Pulley PivotLoop Handle RH Loop Handle LHLower Tube Pivot SupportRetainer SpacerKnob RED Handle KnobCarriage Bolt 5/16−18 X 155377 NUT 5/16−18 169675 Console Panel Wire HarnessHeadlight Bezel Flood HeadlightRepair Parts Snow Thrower - Model Number XT8527ES Drive 43 402689 Drive Plate Assembly Speed Selector AssemblyEND Plate Control ARMRoll PIN 3/16 Axle ShaftSprocket Clik PIN423184X505 Engine Mount Plate KEY Part Description Engine Tecumseh Model LH318SA-156551HImpeller Belt Belt CoverTraction Belt 187865X428 Wheel Assembly LH187833X428 35062 Safety Ignition KEYPart KEY Description DECAL, DANGER, Deflector 181037DECAL, Danger Service Notes Service Notes Limited Warranty