Poulan 403919, 96192000900 owner manual Before Starting the Engine, Scraper BAR, To Start Engine

Page 11

OPERATION

TO ADJUST SKID PLATES (See Fig. 16)

NOTE: The wrench provided in your parts bag may be used to adjust the skid plates.

Skid plates are located on each side of the auger housing and adjust the clearance between the scraper bar and the ground surface. Adjust skid plates evenly to proper height for current surface conditions. For removal of snow in normal conditions, such as a paved driveway or sidewalk, place skid plates in the highest position (lowest scraper clearance) to give a 1/8" clearance between the scraper bar and the ground. Use a middle position if the surface to be cleared is uneven.

NOTE: It is not recommended to operate the snow thrower over gravel or rocky surfaces. Objects such as gravel, rocks or other debris, can easily be picked up and thrown by the impeller, which can cause serious personal injury, property damage or damage to the snow thrower.

If snow thrower must be operated over gravel surface, use extra caution and be sure skid plates are adjusted to lowest (highest scraper clearance) position.

1.Shut off engine and wait for all moving parts to stop.

2.Adjust skid plates by loosening the rear 1/2" hex nut only, then moving skid plate to desired position.Be sure both plates are adjusted evenly. Tighten securely.

HIGH POSITION (LOW GROUND CLEARANCE)

AUGER

HOUSING

SKID PLATE

1/2" HEX NUT

LOW POSITION (HIGH GROUND CLEARANCE)

FIG. 16

SCRAPER BAR

The scraper bar is not adjustable, but is reversible. After considerable use it may become worn. When it has worn almost to the edge of the housing, it can be reversed, providing additional service before requiring replacement. Replace a damaged or worn scraper bar.

BEFORE STARTING THE ENGINE

CHECK ENGINE OIL LEVEL (See Fig. 17)

The engine on your snow thrower has been shipped, from the factory, already filled with oil.

1.Check engine oil with snow thrower on level ground.

2.Remove oil fill cap/dipstick and wipe clean, reinsert the dipstick and screw tight, wait for a few seconds, remove and read oil level. If necessary, add oil until “FULL” mark on dipstick is reached. Do not overfill.

To change engine oil, see “TO CHANGE ENGINE OIL” in the Maintenance section of this manual.

ADD GASOLINE (See Fig. 17)

Fill fuel tank to bottom of tank filler neck. Do not over- fill. Use fresh, clean, regular unleaded gasoline with a minimum of 87 octane. Do not mix oil with gasoline.

Purchase fuel in quantities that can be used within 30

 

days to assure fuel freshness.

11

WARNING: Wipe off any spilled oil or fuel. Do not store, spill or use gasoline near an open flame.

CAUTION: Alcohol blended fuels (called gasohol or using ethanol or methanol) can at- tract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. To avoid engine problems, the fuel system should be emptied before storage of 30 days or longer. Drain the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel next season. See Storage Instructions for additional information. Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

CHOKE

ENGINE OIL

GASOLINE

CONTROL

FILL CAP / DIPSTICK

FILLER CAP

 

 

FUEL SHUT-

 

 

OFF VALVE

 

 

STARTER

 

 

BUTTON

PRIMER

RECOIL

 

SAFETY

STARTER

HANDLE

IGNITION

ON / OFF

KEY

SWITCH

 

NOTE: ALL ITEMS ARE SHOWN IN THEIR TYPICAL LOCATION. ACTUAL LOCATION MAY VARY WITH ENGINE ON YOUR UNIT.

FIG. 17

TO START ENGINE

Be sure fuel shut-off valve is in the “OPEN” position.

Your snow thrower engine is equipped with both a 120 Volt A.C. electric starter and a recoil starter. The electric starter is equipped with a three-wire power cord and plug and is designed to operate on 120 Volt A.C. household current.

Be sure your house is a 120 Volt A.C. three-wire grounded system. If you are uncertain, consult a licensed electrician.

WARNING: Do not use the electric starter if your house is not a 120 Volt A.C. three-wire grounded system. Se- rious personal injury or damage to your snow thrower could result.

Image 11
Contents Snow Thrower Model NumberSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Remove Snow Thrower from Carton Parts Packed Separately in Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Unfold Upper Handle Install Speed Control ROD See FigsInstall Traction Drive Control ROD See Figs Check Tire Pressure Install Auger Control ROD See FigsInstall Discharge Chute / Chute Rotater Head See Fig Ignition KEY OperationKnow Your Snow Thrower PrimerRecoil auxiliary starter handle used for starting the engine Meets A.N.S.I. Safety RequirementsTo USE Choke Control See Fig HOW to USE Your Snow ThrowerStopping To USE Fuel SHUT-OFF Valve See FigTo Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigTo Throw Snow See Fig To Start Engine Before Starting the EngineScraper BAR If Recoil Starter has Frozen Snow Throwing TipsBefore Stopping Maintenance Engine CleaningChute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height To Remove Wheels See Fig Other StorageTroubleshooting Service Notes Limited Warranty

403919, 96192000900 specifications

The Poulan 403919,96192000900 is a highly regarded chainsaw model designed for both professional and home use. Known for its reliability and performance, it is ideal for a variety of tasks, including tree trimming, firewood cutting, and general yard work. This chainsaw combines advanced technology with user-friendly features, making it a top choice for those who require power and efficiency.

One of the standout features of the Poulan 403919 is its powerful engine. Equipped with a robust 2-cycle engine, this chainsaw provides users with the necessary power to tackle even the toughest jobs. With an engine displacement that ensures optimal performance, users can enjoy quick cutting speeds and reduced vibration, making it comfortable for extended use.

The chainsaw features an adjustable automatic oiler that supplies the bar and chain with the right amount of lubrication. This not only extends the life of the chain and bar but also ensures smooth and efficient operation. Additionally, the easy-access air filter allows for simpler maintenance, ensuring that the engine runs clean and cool, contributing to its longevity.

Safety is also a priority with the Poulan 403919. It is equipped with a chain brake for enhanced safety, allowing users to stop the chain quickly in case of kickback. The ergonomic design provides a comfortable grip, reducing fatigue during prolonged use. Furthermore, the front and rear hand guards are designed to protect the user from debris and accidental contact with the chain.

The Poulan 403919 also features a tool-less chain tensioning system, enabling users to adjust the chain quickly and easily without the need for additional tools. This feature enhances convenience, allowing for quick adjustments in the field, which is especially useful for those who need to switch tasks frequently.

Overall, the Poulan 403919,96192000900 is a versatile, powerful, and user-friendly chainsaw that combines safety and efficiency, making it an excellent choice for both professionals and DIY enthusiasts. With its robust construction, easy maintenance features, and advanced safety measures, it stands out as a reliable tool that can handle a variety of cutting tasks with ease. Whether you're pruning trees or cutting firewood, the Poulan 403919 delivers the performance you need.