REPAIR PARTS SNOW THROWER - MODEL PP11H30ES (96192001401)
AUGER HOUSING / IMPELLER ASSEMBLY
KEY | PART |
| KEY | PART |
|
|
NO. | NO. | DESCRIPTION | NO. | NO. | DESCRIPTION |
|
4 | 191079 | Pulley, Impeller | 30 | 405973X479 | Auger Assembly, RH | |
5 | 188909 | Bearing Assembly, Flange | 31 | 405972X479 | Auger Assembly, LH | |
6 | 198541 | Nut, Hex Flange | 32 | 174699 |
| |
7 | 180355 | Bolt, Flat Head, Carriage | 33 | 174700 | Bushing, Flange | 3/4 |
|
| 34 | 174681 | Washer, Thrust | 3/4 | |
8 | 72270505 | Bolt, Carriage | 35 | 174684 | Bearing, Thrust | 3/4 |
9 | 199879 | Bolt, Hex Head | 36 | 174660 | Shaft, Impeller |
|
10 | 404927X428 | Housing, Auger | 37 | 174683 | Washer, Thrust 5/8 | |
11 | 404933X479 | Bar, Scraper | 38 | 174686 | Bushing, Flange 5/8 | |
12 | 178675X008 | Bracket, Corner Discharge | 39 | 150078 | Screw, Hex Head | |
13 | 175322 | Base, Discharge Chute | 40 | 86447 | Plug, Case |
|
14 | 19111507 | Washer, Flat | 41 | 174688 | Housing, Gearbox, RH | |
15 | 198552 | Washer, Lock 5/16 | 42 | 174698 | Seal, Oil |
|
16 | 74950512 | Screw, Hex Head | 43 | 174701 | Bushing, Flange, 1" | |
17 | 405637 | Grease Fitting | 44 | 189282 | Key, Square 1/4 x 1/4 x 7/8 | |
18 | 179582 | Screw, Hex Head 5/16 x 1 | 45 | 174659 | Gear, Worm |
|
19 | 73800400 | Nut, Hex Lock | 46 | 174657 | Shaft, Auger |
|
20 | 198541 | Nut, Hex Lock | 47 | 174687 | Housing, Gearbox, LH | |
21 | 401347 | Washer, Flat | 48 | 175321X479 | Impeller Assembly | |
22 | 178777X479 | Skid Plate, RH | 49 | 74780426 | Screw, Hex Head | |
24 | 128638 | Wing Nut | 50 | 175311 | Gasket, Gearbox | |
25 | 72270506 | Bolt, Carriage | 51 | 7836M | Pin, Roll 3/16 x | |
26 | 174658 | Bearing, Auger | 52 | 405697X479 | Bar, Drift Cutter |
|
27 | 174697 | Washer, Thrust, 1" | 54 | 198709 | Stop |
|
28 | 198636 | Bolt, Shear | 55 | 198638 | Spacer |
|
29 | 174762X479 | Skid Plate, LH | 56 | 180684 |
| |
|
|
| 57 | 178878 | Gearbox Assembly |
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. 21