Poulan 435555 Impeller Belt, Traction Belt, Idler ARM Bracket, Idler Pulley, Idler Bracket

Page 36

REPAIR PARTS SNOW THROWER - MODEL PP291E30 (96198003001)

CHASSIS / ENGINE / PULLEYS

27

23

22

			13
			21
			20
25
24
13	21		19
15			26
15					18
					18
11					17
					17
12					16
13		14			16
13		14
			7
		5
9
				4	6
				4
10			3		1
10					2
				8

01.21.020-B

KEY	PART
NO.	NO.	DESCRIPTION
1	419888	IMPELLER BELT
2	427304	TRACTION BELT
3	423723X431	IDLER ARM BRACKET
4	180523	IDLER PULLEY
5	423990X431	IDLER BRACKET
6	426589	NUT 5/16-18
7	74780524	SCREW 5/16-18 X 1.50
8	424297	SHOULDER BOLT 5/16-18 X .50
9	751153	NUT 5/16-18 LOCK
10	428867	SCREW 5/16-18 X .625

11427576 TRACTION IDLER BRACKET

12180522 TRACTION PULLEY

13	59289	WASHER
14	73800500	NUT 5/16-18

KEY	PART
NO.	NO.	DESCRIPTION
15	74780520	SCREW 5/16-18 X 1.25
16	851084	SCREW 3/8-24 X 1 .375
17	19132005	WASHER

18425934 PULLEY ENG IMPELLER

19425933 PULLEY ENG TRACTION

2074610516 SCREW 5/16-24 X 1.00

2110040500 LOCKWASHER 5/16

22

155452

BELT GUIDE

2311050500 LOCKWASHER 5/16

24175331 IDLER BUSHING

2519112206 WASHER

2674610520 SCREW 5/16-24 X 1.25

2774760608 SCREW 3/8-16 X .750

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty.

36

Image 36

Contents Model Number Snow ThrowerSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Assembly / PRE-OPERATION HOW to SET UP Your Snow ThrowerRemove Snow Thrower from Carton Unfold Upper HandleInstall Traction Drive Control ROD See Figs Install Auger Control ROD See FigsInstall Discharge Chute / Chute Rotator Head See Fig Install Chute Deflector Remote Control See FigsCheck Tire Pressure Operation Know Your Snow ThrowerPrimer Ignition KEYMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting engineHOW to USE Your Snow Thrower StoppingTo USE Fuel SHUT-OFF Valve See Fig To USE Choke Control See FigUsing the CLEAN-OUT Tool See Fig To Adjust Skid Plates See FigTo Throw Snow See Fig To Move Forward and Backward See FigBefore Starting the Engine Scraper BAR See FigTo USE Drift Cutters See Fig Check Engine OIL Level See FigSnow Throwing Tips To Start EngineBefore Stopping If Recoil Starter has FrozenMaintenance Cleaning EngineService and Adjustments To Adjust Snow Thrower HeightChute Deflector Shear Bolts See FigTo Replace Belts See Fig To Adjust Cable Tension See Fig To Remove Wheels See FigCarburetor Engine SpeedStorage OtherFuel System Engine OILTroubleshooting Auger Housing KEY Part DescriptionScrapper BAR Auger BearingExploded Gearbox Assembly 178675X008 Corner Bracket Clean OUT ToolBearing Impeller PulleyAuger Assembly 30 LH Auger Assembly 30 RHSkid Plate LH Skid Plate RH181160X431 Drift Cutter BAR Plastic WasherKnob Black POP RivetChute Snow Shield Shield Retainer StrapLEVER/CABLE Rotator Assembly Cable Assembly AdjustableRotator Head Rotator Pivot BracketRepair Parts Snow Thrower Model PP291E30 Handles Loop Handle LH Loop Handle RHLower Handle Pivot Support WeldmentSpacer Knob REDHandle Knob Washer 3/8Carriage Bolt 5/16-18 X 155377 NUT 5/16-18 169675 Repair Parts Snow Thrower Model PP291E30 Drive Assembly Drive Plate AssemblySpeed Selector Rubber RingRepair Parts Axle ShaftRoll PIN 3/16 SprocketComplete LCT Engine Frame427963X428 Engine Mounting PlateImpeller Belt Traction BeltIdler ARM Bracket Idler PulleyRepair Parts Snow Thrower Model PP291E30 Wheels Wheel Assembly LH432335X421 432336X421Repair Parts Snow Thrower Model PP291E30 BAG of Parts Safety Ignition KEY422663 Repair Parts Snow Thrower Model PP291E30 Decals DECAL, DangerDECAL, DANGER, Deflector DECAL, InstructionLimited Warranty