Poulan 96198002501, 424714 owner manual Parts Packed Separately in Carton, Assembly / PRE-OPERATION

Page 4

PARTS PACKED SEPARATELY IN CARTON

(1) AUGER CONTROL ROD

(1) TRACTION DRIVE CONTROL ROD

(1) MULTI-

WRENCH

(180684)

(2) FLAT WASHERS

 

(1) POWER CORD

 

(1) DISCHARGE CHUTE

(198563)

(3) RETAINER

 

 

 

 

 

SPRINGS

 

 

(169675)

ROTATOR HEAD MOUNTING

(2) CARRIAGE BOLTS 3/8-16 x 2.25

(1) WASHER 3/8

(1) LOCKNUT 3/8

(1) SAFTEY IGNITION KEY

(35062)

(19131316)

(73800600)

 

(2) HANDLE KNOBS

EXTRA SHEAR BOLTS AND NUTS

(2) SHEAR BOLTS 1/4-20 x 1-3/4

(2) SPACERS

(2) LOCKNUTS

(198636)

(198638)

1/4-20

 

 

(73800400)

ASSEMBLY / PRE-OPERATION

Read these instructions and this manual in its entirety

 

2.

Cut down all four corners of carton and lay panels flat.

before you attempt to assemble or operate your new

 

3.

Remove the two (2) screws securing the auger housing

snow thrower. Reading the entire manual will familiar-

 

 

 

to the pallet.

ize you with the unit, which will assist you in assembly,

 

 

 

4.

Remove all packing materials except plastic tie holding

operation and maintenance of the product.

 

Your new snow thrower has been assembled at the factory

 

 

speed control rod to lower handle.

 

5.

Remove the two (2) plastic ties securing the upper

with the exception of those parts left unassembled for ship-

 

ping purposes. All parts such as nuts, washers, bolts, etc.,

 

 

handle to the pallet.

necessary to complete the assembly have been placed in

 

6.

Remove snow thrower from carton and check carton

the parts bag. To ensure safe and proper operation of your

 

 

thoroughly for additional loose parts.

snow thrower, all parts and hardware you assemble must

 

HOW TO SET UP YOUR SNOW THROWER

be tightened securely. Use the correct tools as necessary

 

to ensure proper tightness.

 

TOOL BOX (See Fig. 8)

 

 

REMOVE SNOW THROWER FROM CARTON

 

A toolbox is provided on your snow thrower. The toolbox is

1. Remove all accessible loose parts and parts boxes

 

located on top of the belt cover. Store the extra shear bolts,

4

nuts and multi-wrench provided in parts bag in the toolbox.

from carton.

 

 

Image 4
Contents Model Number Snow ThrowerSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Assembly / PRE-OPERATION HOW to SET UP Your Snow ThrowerParts Packed Separately in Carton Remove Snow Thrower from CartonInstall Traction Drive Control ROD See Figs Install Speed Control ROD See FigsUnfold Upper Handle Install Discharge Chute / Chute Rotator Head See Fig Install Auger Control ROD See FigsCheck Tire Pressure Operation Know Your Snow ThrowerRecoil auxiliary starter handle used for starting Meets A.N.S.I. Safety RequirementsDrive speed control lever used to select forward or HOW to USE Your Snow Thrower StoppingTo Throw Snow See Fig Using the CLEAN-OUT Tool See FigTo Move Forward and Backward See Fig Before Starting the Engine Before Stopping Snow Throwing TipsIf Recoil Starter has Frozen Maintenance Cleaning EngineTo Adjust Snow Thrower Height Service and AdjustmentsChute Deflector Frame Auger Assembly Housing Handles Storage CarburetorEngine Speed Fuel SystemOther CylinderTroubleshooting Auger Housing / Impeller Assembly KEY Part DescriptionAuger 27 LH Auger 27 RHSkid Plate LH Skid Plate RHExploded Gearbox Assembly 178675X008 Corner Bracket Clean OUT ToolBearing Impeller PulleyControl Panel / Discharge Chute LEVER/CABLE Rotator Assembly Cable AssemblyRotator Head Rotator Pivot Bracket419797X479 HandlesLower Tube 01.08.004-B Control Panel Control Lever LHSpacer RetainerCarriage Bolt 5/16−18 X 155377 NUT 5/16−18 169675 Drive Speed Selector Assembly Drive Plate AssemblyShoulder Screw END PlateAxle Shaft Roll PIN 3/16Sprocket Clik PINChassis / Engine / Pulleys ENGINE, TECFrame Engine Mount PlateTraction Belt Belt CoverImpeller Belt Wheel Assembly LH WheelsBAG of Parts Safety Ignition KEY35062 Decals 181037DECAL, Danger DECAL, DANGER, DeflectorService Notes Service Notes Limited Warranty