Poulan 435548 Before Starting the Engine, Scraper BAR See Fig, To USE Drift Cutters See Fig

Page 12

OPERATION

NOTE: It is not recommended to operate the snow thrower over gravel or rocky surfaces. Objects such as gravel, rocks or other debris, can easily be picked up and thrown by the impeller, which can cause serious personal injury, property damage or damage to the snow thrower.

•If snow thrower must be operated over gravel surface, use extra caution and be sure skid plates are adjusted to lowest (highest scraper clearance) position.

1.Shut off engine and wait for all moving parts to stop.

2.Adjust skid plates by loosening the hex nuts, then mov- ing skid plate to desired position. Be sure both plates are adjusted evenly. Tighten securely.

HIGH POSITION

 

(LOW GROUND

 

CLEARANCE)

 

 

AUGER

 

HOUSING

 

SCRAPER BAR

HEX

SKID PLATE

NUTS

LOW POSITION (HIGH GROUND CLEARANCE)

FIG. 18

SCRAPER BAR (See Fig. 18)

The scraper bar is not adjustable, but is reversible. After considerable use it may become worn. When it has worn almost to the edge of the housing, it can be reversed, providing additional service before requiring replacement. Replace a damaged or worn scraper bar.

TO USE DRIFT CUTTERS (See Fig. 19)

Use the drift cutters to cut through deep snowdrifts that are higher than the front of the snow thrower.

•Loosen adjustment nuts enough to allow drift cutter to be raised to highest position and tighten nuts securely. Repeat for opposite side of snow thrower.

•When not using drift cutters, loosen adjustment nuts, lower to storage position and tighten nuts securely.

AUGER

HOUSING

STORAGE

DRIFT

POSITION

CUTTER

ADJUST-

MENT NUTS

FIG. 19

BEFORE STARTING THE ENGINE

CHECK ENGINE OIL LEVEL (See Fig. 20)

The engine on your snow thrower has been shipped from the factory already filled with oil.

1.Check engine oil with snow thrower on level ground.

2.Remove oil fill cap/dipstick and wipe clean, reinsert the dipstick and screw tight, wait for a few seconds, remove and read oil level. If necessary, add oil until “FULL” mark on dipstick is reached. Do not overfill.

•To change engine oil, see “TO CHANGE ENGINE OIL” in the Maintenance section of this manual.

ADD GASOLINE (See Fig. 20)

•Fill fuel tank to bottom of tank filler neck. Do not over- fill. Use fresh, clean, regular unleaded gasoline with a minimum of 87 octane. Do not mix oil with gasoline. Purchase fuel in quantities that can be used within 30 days to assure fuel freshness.

WARNING: Wipe off any spilled oil or fuel. Do not store, spill or use gasoline near an open flame.

CAUTION: Alcohol blended fuels (called gaso- hol or using ethanol or methanol) can attract moisture which leads to separation and forma- tion of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. To avoid engine problems, the fuel system should be emptied before storage of 30 days or longer. Empty the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel next season. See Storage Instructions for additional information. Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

ON / OFF

RECOIL (AUXILIARY)

STARTER HANDLE

SWITCH

 

 

GASOLINE

 

FILLER CAP

CHOKE

ENGINE OIL FILL

CAP / DIPSTICK

CON-

 

TROL

 

 

STARTER

 

BUTTON

SAFETY

 

IGNITION

 

KEY

 

PRIMER

 

 

POWER

 

CORD

FUEL SHUT-OFF VALVE

PLUG

NOTE: ALL ITEMS ARE SHOWN IN THEIR TYPICAL LOCATION. ACTUAL LOCATION MAY VARY WITH ENGINE ON YOUR UNIT.

12

FIG. 20

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Model Number Snow ThrowerSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Assembly / PRE-OPERATION HOW to SET UP Your Snow ThrowerParts Packed Separately in Carton Remove Snow Thrower from CartonInstall Speed Control ROD See Figs Install Traction Drive Control ROD See FigsUnfold Upper Handle Install Auger Control ROD See Figs Install Discharge Chute / Chute Rotater Head See FigInstall Chute Deflector Remote Control See Figs Check Tire PressureOperation Know Your Snow ThrowerPrimer Ignition KEYMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting the engineHOW to USE Your Snow Thrower StoppingUsing the CLEAN-OUT Tool See Fig Power Steering Operation See FigTo Adjust Skid Plates See Fig To Move Forward and Backward See FigBefore Starting the Engine Scraper BAR See FigTo USE Drift Cutters See Fig Check Engine OIL Level See FigSnow Throwing Tips To Start EngineBefore Stopping If Recoil Starter has FrozenMaintenance General RecommendationsBefore Each USE LubricationCleaning EngineService and Adjustments To Adjust Snow Thrower HeightChute Deflector Shear Bolts See FigTo Replace Belts See Fig To Adjust Cable Tension See Fig To Remove Wheels See FigCarburetor Engine SpeedStorage OtherFuel System Engine OILTroubleshooting Service Notes Exploded KEY Part Description Auger Housing Scraper BARAuger Bearing Bearing PlugAuger 27 LH Auger 27 RHSkid Plate LH Skid Plate RHKEY Part Drift Cutter BARCARRIAGEBOLT5/16−18X.750 Plastic WasherKnob Black POP RivetChute Snow Shield 419822X431 Shield Retainer Strap LEVER/CABLE Rotator Assembly Cable Assembly AdjustableCable Assembly Heat Shield Rotator HeadLoop Handle LH Loop Handle RHLower Tube Pivot SupportSpacer RetainerKnob RED Handle KnobImpeller ROD Assembly Traction ROD AssemblyShifter ROD TOP Shifter ROD BottomWire Harness Console PanelHeadlight Bezel Flood HeadlightRepair Parts Snow Thrower - Model Number PP291EPS27 Drive Exploded Assembly Drive Plate AssemblySpeed Selector Rubber RingComplete LCT Engine Frame427963X428 Engine Mounting PlateImpeller Belt Traction BeltIdler ARM Bracket Idler Pulley01.21.014-C 428685Wheel Assembly LH Cable Bracket LHCable Bracket RH Cover Wheel Driver Retainer RingWheel Lobe Clutch SlideSafety Ignition KEY 422663181037 DECAL, DangerDECAL, DANGER, Deflector DECAL, InstructionService Notes Limited Warranty

96198002901, 435548 specifications

The Poulan 96198002901, 435548 is a cutting-edge lawn mower designed for homeowners who seek a balance between performance and ease of use. Offering a powerful engine and a range of innovative features, this model is ideal for maintaining a well-manicured lawn with minimal effort.

One of the standout features of the Poulan mower is its robust 4-cycle engine that delivers exceptional power and efficiency. This engine is designed to provide a smooth operation while generating enough torque to tackle thick grass and uneven terrain. Coupled with an easy pull-start mechanism, users can quickly get their mower ready for action without the frustration often associated with recoil starters.

The mower's cutting deck is another highlight, with a size that optimally balances maneuverability and coverage. It allows for efficient cutting while reducing the time spent on mowing. Additionally, the adjustable cutting height provides users with flexibility, allowing them to choose the desired grass length. This is particularly useful for those who vary their lawn care practices throughout the growing season.

Maneuverability is further enhanced by the lightweight design of the Poulan 96198002901, 435548. Portability does not come at the cost of durability, as the mower is crafted from high-quality materials that ensure longevity. Furthermore, its compact size makes it easy to store, even in tight spaces.

The mower comes equipped with advanced technologies that improve its overall user experience. One notable feature is the automatic throttle control, which adjusts the engine speed based on the mower's workload. This not only extends the mower’s life but also enhances fuel efficiency, making it a cost-effective option for long-term lawn care.

Safety features are paramount, and the Poulan model includes a safety guard that automatically shuts off the blades when the user releases the handle. This is a crucial aspect for preventing accidents, particularly in households with children or pets.

In summary, the Poulan 96198002901, 435548 stands out as a reliable lawn mower that combines power, efficiency, and user-friendly features. With its sturdy construction, advanced technologies, and adjustable settings, it is designed to meet the diverse needs of homeowners looking to maintain their lawns effortlessly. Whether you have a small yard or a larger space, this mower promises to deliver excellent results while ensuring a safe and enjoyable mowing experience.
Top Page Image Contents