Poulan 96198002601 Service and Adjustments, To Adjust Snow Thrower Height, Chute Deflector

Page 15

SERVICE AND ADJUSTMENTS

WARNING: To avoid serious injury, before performing any service or ad- justments:

1.Be sure the on/off switch is in the OFF position.

2.Remove safety ignition key.

3.Make sure the augers and all moving parts have completely stopped.

4.Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug.

To replace the capscrew/shear bolts:

1.Disengage all controls and move throttle control to STOP position. Wait for all moving parts to stop.

2.Remove safety ignition key and disconnect spark plug wire from spark plug. Place wire where it cannot come in contact with spark plug.

3.Align holes in impeller hub with holes in impeller shaft and install two (2) new 1/4-20 x 1-5/8" capscrew/shear bolts. Install 1/4-20 locknuts and tighten securely.

CAUTION: Do not substitute. Use only original equipment capscrew/shear bolts as supplied with your snow thrower.

SNOW THROWER

TO ADJUST SNOW THROWER HEIGHT

See “TO ADJUST SKID PLATES” and “SCRAPER BAR” in the Operation section of this manual.

CHUTE DEFLECTOR

The chute deflector, attached to the top of the discharge chute, is provided to direct discharging snow away from the operator. If the deflector becomes damaged, it should be replaced.

WARNING: To avoid serious injury, never operate your snow thrower with the deflector removed or damaged.

•To change direction and/or distance snow is discharged, see “TO CONTROL SNOW DISCHARGE” in the Op- eration section of this manual.

SHEAR BOLTS (See Fig. 18)

AUGER SHEAR BOLTS

Both right and left-hand augers are secured to the auger shaft with a spacer, shear bolt and hex nut. Should a foreign object or ice become lodged in the augers, the shear bolts are designed to break, preventing damage to any other components. If one or both augers do not turn when auger control lever is engaged, check to see if one or both of the bolts have sheared. To replace the shear bolts:

1.Disengage all controls and move throttle control to STOP position. Wait for all moving parts to stop.

2.Remove safety ignition key and disconnect spark plug wire from spark plug. Place wire where it cannot come in contact with spark plug.

3.Align hole in auger hub with hole in auger shaft and install a new 1/4-20 x 2" shear bolt. Install 1/4-20 lock nut and tighten securely.

CAUTION: Do not substitute. Use only original equipment shear bolts as supplied with your snow thrower.

4.Insert safety ignition key and reconnect spark plug wire to spark plug.

IMPELLER SHEAR BOLTS

The impeller is secured to the impeller shaft with two (2) capscrew/shear bolts and hex nuts. Should a foreign object or ice become lodged in the impeller, the capscrews are designed to break, preventing damage to any other com- ponents. If impeller does not turn when auger control lever

is engaged, check to see if the capscrews have sheared. 15

4.Insert safety ignition key and reconnect spark plug wire to spark plug.

1/4-20

1/4-20 x 1-5/8

1/4-20 x 2

LOCKNUT

CAPSCREW /

SHOULDER /

 

SHEAR BOLT

SHEAR BOLT

 

IMPELLER HUB

 

 

IMPELLER

 

 

SHAFT

 

 

 

AUGER

 

 

HUB

1/4-20

 

 

LOCKNUT

AUGER HUB

AUGER SHAFT

FIG. 18

TO REMOVE BELT COVER (See Fig. 19)

1.Remove the two (2) screws securing belt cover to frame.

2.Remove belt cover.

3.Replace belt cover by installing cover and screws and tighten securely.

BELT

COVER

FRAME

SCREWS

FIG. 19

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Snow Thrower Model NumberSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Remove Snow Thrower from Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Parts Packed Separately in CartonInstall Speed Control ROD See Figs Install Traction Drive Control ROD See FigsUnfold Upper Handle Install Auger Control ROD See Figs Install Discharge Chute / Chute Rotater Head See FigCheck Tire Pressure Ignition KEY OperationKnow Your Snow Thrower PrimerElectric start button used for starting the engine Meets A.N.S.I. Safety RequirementsTo USE Choke Control See Fig HOW to USE Your Snow ThrowerStopping To USE Fuel SHUT-OFF Valve See FigUsing the CLEAN-OUT Tool See Fig To Throw Snow See FigTo Move Forward and Backward See Fig Before Starting the Engine If Recoil Starter has Frozen Snow Throwing TipsTo Start Engine Before StoppingLubrication MaintenanceGeneral Recommendations Before Each USEEngine CleaningShear Bolts See Fig Service and AdjustmentsTo Adjust Snow Thrower Height Chute DeflectorTo Replace Belts See Fig Engine Speed To Adjust Cable Tension See FigTo Remove Wheels See Fig CarburetorEngine OIL StorageOther Fuel SystemTroubleshooting Exploded KEY Part Description Scrapper BAR Auger HousingAuger Assembly LH Auger Assembly RHBearing Plug Auger BearingStrap Chute WeldmentDeflector Weldment Deflector SealRotator Head LEVER/CABLE Rotator AssemblyCable Assembly Adjustable Cable Assembly Heat ShieldPivot Support Panel Bracket LH Panel Bracket RHHandle Grip Lower TubeHandle Knob SpacerRetainer Knob REDShifter ROD Bottom Impeller RODTraction ROD Shifter ROD TOPTorsion Spring Console PanelInterlock Spring Interlock CAMRepair Parts Snow Thrower - Model Number PP208E24 Drive Rubber Ring AssemblyDrive Plate Assembly Speed SelectorClik PIN Axle ShaftRoll PIN 3/16 Sprocket427963X428 Engine MountingPlate Idler Pulley Impeller BeltTraction Belt Idler ARM BracketWheel Assembly LH 187831X421187866X421 422663 Safety Ignition KEYDECAL, Auger Lever RT DECAL, DangerDECAL, DANGER, Deflector DECAL, InstructionService Notes Service Notes Limited Warranty

96198002601, 428701 specifications

The Poulan 428701,96198002601 is a powerful and efficient chainsaw designed for homeowners and professionals alike. This model combines advanced technology with user-friendly features, making it a top choice for those looking to tackle various chopping and cutting tasks with ease.

One of the key features of this chainsaw is its robust engine, which provides dependable performance. The Poulan 428701 is equipped with a 40cc two-cycle engine that delivers ample power for cutting through large tree limbs, firewood preparation, and even light commercial work. The engine's design focuses on fuel efficiency, ensuring that users can work longer without frequent refueling.

In terms of technology, the chainsaw incorporates a tool-less chain tensioning system that allows users to adjust the chain’s tension quickly and easily. This feature not only saves time but also enhances safety, as a correctly tensioned chain reduces the risk of kickback and improves cutting performance. The easy-access air filter ensures that maintenance is simple, allowing users to keep their chainsaw performing optimally with minimal effort.

The Poulan 428701 also boasts a lightweight design, weighing in at just under 12 pounds. This makes it manageable for extended use without causing fatigue, making it suitable for both beginners and experienced users. The ergonomic handle is designed for comfort, providing a secure grip that enhances control during operation.

Safety is a significant concern with power tools, and this chainsaw is equipped with a chain brake mechanism. The chain brake stops the chain immediately in case of a kickback, protecting the user from potentially serious injuries. Its low vibration technology further reduces operator fatigue and increases comfort for prolonged use.

Another notable characteristic of the Poulan 428701 is its durable construction. Built with high-quality materials, this chainsaw is designed to withstand the rigors of regular use while maintaining its performance. The bar and chain are designed for longevity, with easy compatibility for replacements when necessary.

In summary, the Poulan 428701,96198002601 chainsaw is a reliable and efficient tool that combines power, safety, and ease of use. With features such as a powerful engine, tool-less chain tensioning, low vibration, and a focus on user comfort, it caters to a wide range of cutting needs, making it a worthwhile addition to any toolkit. Whether for home landscaping or professional use, this chainsaw delivers performance that users can trust.
Top Page Image Contents