Poulan 428496 Impeller Belt, Traction Belt, Idler ARM, Idler Bushing, Idler Bracket, Idler Pulley

Page 34

REPAIR PARTS SNOW THROWER - - MODEL NUMBER PP208E24 (96198002600)

CHASSIS / ENGINE / PULLEYS

	24 23	14 22
25		14 22
			21
	14 22		20	19
	14 22		21	19
13			21
13						18
11						18
11						17
12						17
12	14 15					16
						16
			6
			6
			4
	8				5	7
				3	5
						1

	10
	10					2
						2
				9

01.21.001-A

KEY	PART	DESCRIPTION	KEY	PART	DESCRIPTION
NO.	NO.	DESCRIPTION	NO.	NO.	DESCRIPTION
1	408007	IMPELLER BELT	14	59289	WASHER
2	419744	TRACTION BELT	15	73930500	NUT 5/16-18
3	419925X479	IDLER ARM	16	851084	IDLER BUSHING
4	193397X479	IDLER BRACKET	17	400026	WASHER
5	180523	IDLER PULLEY	18	179157	ENGINE PULLEY
6	74780524	SCREW 5/16-18 X 1.50	19	180478	ENGINE TRACTION PULLEY
7	426589	NUT 5/16-18	20	409475	SPACER
8	175330	IDLER ARM PIN	21	74610516	SCREW 5/16-18 X 1.00
9	85179	RETAINER CLIP	22	10040500	LOCKWASHER 5/16
10	428867	SCREW 5/16-18 X .625	23	155452	BELT GUIDE
11	187786	TRACTION IDLER ARM	24	11050500	LOCKWASHER 5/16
12	180522	TRACTION PULLEY	25	175331	IDLER BUSHING
13	74780520	SCREW 5/16-18 X 1.00

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty.

34

Image 34

Contents Model Number Snow ThrowerSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Remove Snow Thrower from CartonInstall Traction Drive Control ROD See Figs Install Speed Control ROD See FigsUnfold Upper Handle Install Discharge Chute / Chute Rotater Head See Fig Install Auger Control ROD See FigsCheck Tire Pressure Primer OperationKnow Your Snow Thrower Ignition KEYMeets A.N.S.I. Safety Requirements Electric start button used for starting the engineTo USE Fuel SHUT-OFF Valve See Fig HOW to USE Your Snow ThrowerStopping To USE Choke Control See FigTo Throw Snow See Fig Using the CLEAN-OUT Tool See FigTo Move Forward and Backward See Fig Before Starting the Engine Before Stopping Snow Throwing TipsTo Start Engine If Recoil Starter has FrozenBefore Each USE MaintenanceGeneral Recommendations LubricationCleaning EngineChute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height Shear Bolts See FigTo Replace Belts See Fig Carburetor To Adjust Cable Tension See FigTo Remove Wheels See Fig Engine SpeedFuel System StorageOther Engine OILTroubleshooting 01.07.004-C KEY Part Description Auger Assembly RH Auger HousingAuger Assembly LH Scrapper BARAuger Bearing Bearing PlugDeflector Seal Chute WeldmentDeflector Weldment StrapCable Assembly Heat Shield LEVER/CABLE Rotator AssemblyCable Assembly Adjustable Rotator HeadLower Tube Panel Bracket LH Panel Bracket RHHandle Grip Pivot SupportKnob RED SpacerRetainer Handle KnobShifter ROD TOP Impeller RODTraction ROD Shifter ROD BottomInterlock CAM Console PanelInterlock Spring Torsion SpringRepair Parts Snow Thrower - Model Number PP208E24 Drive Wheelhub Speed Selector AssemblyDrive Plate Assembly END PlateSprocket Axle ShaftRoll PIN 3/16 Clik PINFrame Cover AssemblyComplete LCT Engine 423184X428Idler ARM Impeller BeltTraction Belt Idler Bushing187831X421 Wheel Assembly LH187866X421 Safety Ignition KEY 422663DECAL, Instruction DECAL, DangerDECAL, DANGER, Deflector DECAL, Auger Lever RTService Notes Service Notes Limited Warranty