MTD 769-04101 warranty Attaching the Chute Assembly, Attaching the Shift Rod

Page 7

Figure 3-4

Attaching the Chute Assembly

•Remove locknuts and screws securing one of the flange keepers to the chute assembly. See Figure 3-4.

•Loosen but do not remove the locknuts and screws on the other two flange keepers.

•Slide chute assembly over chute opening, making sure the flange keepers are beneath lip of chute adapter. The notches should engage with the spiral end of the chute crank. See Figure 3-5.

•Secure flange keeper, locknuts and screws previously removed. Tighten all flange keepers and hardware with two 7/16” wrenches. Do not over tighten.

NOTE: If necessary the chute crank support bracket can be adjusted so the spiral on the chute crank fully engages the teeth on the chute assembly. Refer to the Adjustment Section.

Attaching the Shift Rod

•Align the upper and lower shift rods, then slide the shift rod connector down over the end of the lower shift rod. Tap the connector until the lower rod is completely through the connector. See Figure 3-6.

NOTE: If the connector is not properly assembled, the shift rod will pivot and you will not be able to change speeds or direction.

NOTE: If the full range of speeds (forward and reverse) cannot be achieved, refer to the Adjustment Section.

•Normally the cable ties holding the steering cables against the handle are loosely installed on each side of the lower handle at the factory. Pull the cable ties tight to secure. Cut the excess from the ends of cable ties.

•If not already attached, slip the cables that run from the handle panel to the discharge chute into the cable guide. See Figure 3-7.

3

Setting Up

Your Snow

Thrower

Figure 3-5

WARNING

Prior to operating your snow thrower, refer to Auger Control on page 9. Read and follow all instructions carefully and perform all adjustments to verify your unit is operating safely and properly.

Figure 3-6

Figure 3-7

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents 769-04101 28, 30, 33 & 45Two-Stage Snow Throwers05/28/08 Finding and Recording Model Number Table of ContentsCustomer Support Your Responsibility Restrict the use Safety SymbolsThere are rotating blades inside Do not use the engine’s electric starter in the rainYour Responsibility Safe Operation PracticesTraining PreparationAverage Useful Life Maintenance & StorageOperation Do not modify engineAssembling Handle Setting Up Your Snow ThrowerItems Required For Assembly Loose PartsAttaching the Shift Rod Attaching the Chute AssemblyDrift Cutters If Equipped Lamp WiringClean-Out Tool Final AdjustmentsAuger Check the adjustment of the auger control as followsSkid Shoes Tire Pressure Pneumatic TiresKnow Your Snow Thrower Operating Your Snow Thrower$26% #/.42 To Engage Augers Gas & Oil Fill-UpStopping The Engine To Engage DriveIf possible, remove snow immediately after it falls Always observe safety rules when performing any maintenanceOperating Tips General RecommendationsDrive Control AdjustmentsMaking Shift RodAuger Control Chute AssemblyChute Bracket Adjustment See Figure Adjust skid shoes as followsLubrication Maintaining Your Snow ThrowerReplacing Belts Remove Loosen Auger BeltPulley Slot Drive BeltFriction Wheel Using a 3/4 wrench, hold the hex shaftChanging Friction Wheel Rubber Secure with the cupped washer and hex bolt removed earlierOff-Season Storage Problem Cause Remedy Trouble Shooting05.28.08 WarrantyFor parts and/or accessories refer to customer support on 6919 Adressez-vous au «Service après-vente» Parts List Pièces DétachéesLa page 2 pour ce qui concerne les pièces et/ou accessoires Torque to 21 ft./lbs. maximum 305-342 cc618-04514 Worm Gear Box Ass’y w/ grease fitting Part RÉF Pièce Description Style Torque to 325-550 in./lbs Serrez à un couple de 325-550po-lb Part RÉF Pièce Description Part RÉF Pièce Description For parts and/or accessories refer to customer support on Page Com.mtdcanada GarantieGarantie cette de Pas couvre ne limitée garantie CetteDépannage Solution Causes ProblèmePas Jours, 30 de plus pendant entreposé être doit moteur le Si PropreUse Accompagne qui moteur du d’utilisation notice la dansFrottement de Roue Entretien’essieu de Tout empêcher pour Et commandes lesPoulie la De Fente Moteur duBoulon l’autre retirez Éloignez’enlevez Tarière la de d’entraînement Courroie’engrenage LubrificationRoues Vitesse de mentRéglages Support de Des l’entraînement de CommandeVitesses de levier du Tige ’essieuLes de Évitez .65C 150F dépasser Général d’ordre Recommandations’utilisation Conseils ToucherFaites Ne ’huile et d’essence PleinsGoulotte la de dégagement de Outil Fonctions 2 à Roues des d’orientation CommandeGoulotte la de Commande Goulotte la de directionLa de Souffleuse la de CommandesTiques Tarière la de CommandePneuma Bandages pneus des Pression Pas Goulotte la de dégagement de OutilBien passe qu’il ce jusqu’à raccord le sur Tapez Vitesses de levier du tige la de InstallationGoulotte la de Installation «Réglages»Cisaillement de Boulons Goulotte la de manivelle la de MontageGuidon du Montage ’assemblage pour requis ArticlesMoteur le pas modifiez Ne Remisage et EntretienMoyenne utile vie de Durée Gaz de émissions les concernant AvisVotre UtilisationPréparation FormationMachine la d’utiliser Responsabilité Votre’utilisation La voir détachées Pièces Vente-après ServiceModèle de numéro le trouver Pour Matières des Table04101-769 05/28/08

769-04101 specifications

The MTD 769-04101 is a versatile and robust lawn mower designed to deliver efficient performance for both residential and commercial users. Known for its reliability, it offers a host of features that cater to various mowing needs.

One of the standout characteristics of the MTD 769-04101 is its powerful engine. Equipped with a formidable 420cc engine, this mower ensures a strong performance while cutting through thick grass and challenging terrains with ease. The engine is designed for fuel efficiency and minimal emissions, making it an eco-friendly option for users concerned about their carbon footprint.

The MTD 769-04101 features a wide cutting deck, typically measuring 42 inches. This size allows for efficient mowing of large lawns, reducing the time spent on maintaining grassy areas. The deck is constructed from durable materials, ensuring longevity and resilience against wear and tear. With several cutting height options available, users can easily adjust the mower to meet the specific needs of their lawn, achieving a perfect cut every time.

In terms of technology, the MTD 769-04101 includes a reliable electric start system. This feature eliminates the struggle of pull-starting, providing a convenient and user-friendly operation. The mower's transmission system allows for smooth gear shifts, contributing to an overall comfortable mowing experience.

Safety is paramount with the MTD 769-04101. It comes equipped with features such as an automatic blade brake, which ensures that the blades stop quickly when the user releases the handle. This adds an extra layer of protection, making it safer in environments where children or pets may be present.

Another highlight is the mower's ergonomic design. The adjustable handlebar ensures that users of different heights can operate the machine comfortably. Additionally, the mower's maneuverability is enhanced by a tight turning radius, allowing users to navigate around obstacles easily.

Maintenance of the MTD 769-04101 is straightforward thanks to its user-friendly design. The mower provides easy access to various components, ensuring that routine checks and maintenance tasks can be performed without hassle.

Overall, the MTD 769-04101 is a powerful, efficient, and user-friendly choice for anyone looking for a reliable lawn mower. Its combination of technology, safety features, and ergonomic design makes it an excellent investment for maintaining any lawn.
Top Page Image Contents