Poulan 421886 owner manual Meets A.N.S.I. Safety Requirements

Page 8

OPERATION

SPARK			ENGINE OIL CAP	AUGER
PLUG			WITH DIPSTICK	CONTROL
SAFETY				LEVER
IGNITION
KEY			GASOLINE
			GASOLINE
			FILLER
			CAP
CHOKE				CHUTE
CHOKE			DEFLECTOR
CON-			DEFLECTOR
TROL
			FUEL
			SHUT-OFF
			VALVE
THROTTLE
/ ENGINE
CONTROL			DISCHARGE
			DISCHARGE
			CHUTE
RECOIL	POWER
RECOIL	CORD
STARTER	PLUG	ELECTRIC	OIL DRAIN PLUG
HANDLE		ELECTRIC
HANDLE		START
		START
		BUTTON	CLEAN-OUT TOOL

PRIMER

NOTE: ITEMS ABOVE

ARE SHOWN IN

THEIR TYPICAL

LOCATION ON THE

ENGINE. ACTUAL

LOCATION MAY VARY

WITH THE ENGINE

ON YOUR UNIT.

AUGERS

FIG. 8

DISCHARGE CHUTE CONTROL LEVER

DRIVE SPEED	TRACTION
CONTROL LEVER	DRIVE
	CONTROL
	LEVER

LIGHT

HANDLE

KNOB

MUFFLER

TOOLBOX

SKID PLATE

MEETS A.N.S.I. SAFETY REQUIREMENTS

Our snow throwers conform to the standards of the American National Standards Institute.

Toolbox - used to store spare shear bolts, locknuts and wrench.

Safety ignition key - must be inserted for the engine to start and run. Remove when snow thrower is not in use.

Electric start button – used for starting the engine.

Recoil (auxiliary) starter handle – used for starting the engine.

Primer - pumps additional fuel from the carburetor to the cylinder for use when starting a cold engine.

Throttle/engine control - used to select either FAST or SLOW engine speed and to STOP the engine.

Choke control - used for starting a cold engine.

Drive speed control lever - used to select forward or reverse motion and speed of snow thrower.

Traction drive control lever - used to engage power-pro- pelled forward or reverse motion of snow thrower.

Auger control lever - used to engage auger motion (throw snow).

Discharge chute control lever - used to change the di- rection the snow is thrown.

Skid plate - used to adjust height of scraper bar from the

8 ground.

Image 8

Contents Model Number Snow ThrowerSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Assembly / PRE-OPERATION HOW to SET UP Your Snow ThrowerParts Packed Separately in Carton Remove Snow Thrower from Carton Install Speed Control ROD See Figs Unfold Upper HandleCheck Tire Pressure Install Auger Control ROD See FigsInstall Discharge Chute / Chute Rotater Head See Fig Operation Know Your Snow ThrowerPrimer Ignition KEYMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting the engineHOW to USE Your Snow Thrower StoppingTo Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigTo Throw Snow See Fig To Adjust Skid Plates See Fig Before Starting the EngineScraper BAR See Fig Check Engine OIL Level See FigSnow Throwing Tips To Start EngineBefore Stopping If Recoil Starter has FrozenMaintenance General RecommendationsBefore Each USE LubricationCleaning EngineService and Adjustments To Adjust Snow Thrower HeightChute Deflector Shear Bolts See FigTo Replace Belts See Fig Storage OtherTroubleshooting Service Notes Exploded KEY Part Description Auger Housing Auger Assembly LHAuger Assembly RH Scrapper BARAuger Bearing Bearing PlugChute Weldment Deflector WeldmentDeflector Seal StrapLEVER/CABLE Rotator Assembly Rotator HeadRotator Pivot Bracket Pulley Pivot405784X479 Pivot Support Weldment Panel Bracket LH Panel Bracket RHHandle Grip Spacer RetainerKnob RED Handle KnobCarriage Bolt 5/16−18 X 155377 NUT 5/16−18 169675 Wire Harness Console PanelHeadlight Bezel Flood HeadlightRepair Parts Snow Thrower - Model Number PR5524ES Drive Speed Selector Assembly 43 402689 Drive Plate AssemblyEND Plate Control ARMAxle Shaft Roll PIN 3/16Sprocket Clik PINKEY Part Description Engine Tecumseh Model LH195SP-67510D 423184X428 Engine Mount PlateImpeller Belt Belt CoverTraction Belt Repair Parts Snow Thrower - Model Number PR5524ES Wheels Wheel Assembly LHPower Cord Safety Ignition KEYRetainer PIN WrenchDECAL, Danger DECAL, Poulan PRODECAL, DANGER, Deflector DECAL, InstructionService Notes Service Notes Limited Warranty