Poulan 421602 owner manual Meets A.N.S.I. Safety Requirements

Page 8

OPERATION

MUFFLER

GASOLINE

FILLER CAP

CHOKE

CON-

TROL

SAFETY

IGNITION

KEY

ON / OFF

SWITCH

PRIMER

FUEL SHUT-OFF VALVE

RECOIL STARTER HANDLE

NOTE: ITEMS ABOVE

ARE SHOWN IN

THEIR TYPICAL

LOCATION ON THE

ENGINE. ACTUAL

LOCATION MAY

VARY WITH THE

ENGINE ON YOUR

UNIT.

AUGERS

AUGER	DISCHARGE CHUTE CONTROL LEVER	TRACTION
CONTROL		DRIVE
LEVER	DRIVE SPEED	CONTROL
	CONTROL LEVER	LEVER
CHUTE
DEFLECTOR

DISCHARGE

CHUTE

	CLEAN-OUT TOOL	HANDLE
	CLEAN-OUT TOOL	KNOB
		KNOB
		MUFFLER
		TOOLBOX

SKID PLATE

FIG. 8

MEETS A.N.S.I. SAFETY REQUIREMENTS

Our snow throwers conform to the standards of the American National Standards Institute.

Toolbox - used to store spare shear bolts, locknuts and wrench.

Safety ignition key - must be inserted for the engine to start and run. Remove when snow thrower is not in use.

Electric start button – used for starting the engine.

Recoil (auxiliary) starter handle – used for starting the engine.

Primer - pumps additional fuel from the carburetor to the cylinder for use when starting a cold engine.

Throttle/engine control - used to select either FAST or SLOW engine speed and to STOP the engine.

Choke control - used for starting a cold engine.

Drive speed control lever - used to select forward or reverse motion and speed of snow thrower.

Traction drive control lever - used to engage power-pro- pelled forward or reverse motion of snow thrower.

Auger control lever - used to engage auger motion (throw snow).

Discharge chute control lever - used to change the di- rection the snow is thrown.

Skid plate - used to adjust height of scraper bar from the ground

8

Image 8

Contents Model Number Snow ThrowerSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Assembly / PRE-OPERATION HOW to SET UP Your Snow ThrowerParts Packed Separately in Carton Remove Snow Thrower from CartonInstall Speed Control ROD See Figs Unfold Upper HandleCheck Tire Pressure Install Auger Control ROD See FigsInstall Discharge Chute / Chute Rotater Head See Fig Operation Know Your Snow ThrowerPrimer Ignition KEYMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting the engineHOW to USE Your Snow Thrower StoppingTo USE Fuel SHUT-OFF Valve See Fig To USE Choke Control See FigUsing the CLEAN-OUT Tool See Fig To Adjust Skid Plates See FigTo Throw Snow See Fig To Move Forward and Backward See FigBefore Starting the Engine Scraper BAR See FigCheck Engine OIL Level See Fig ADD Gasoline See FigSnow Throwing Tips To Start EngineBefore Stopping If Recoil Starter has FrozenMaintenance General RecommendationsBefore Each USE LubricationCleaning EngineService and Adjustments To Adjust Snow Thrower HeightChute Deflector Shear Bolts See FigTo Replace Belts See Fig Storage OtherTroubleshooting Service Notes Exploded KEY Part Description Auger Housing Scrapper BARAuger Bearing Bearing PlugAuger Assembly LH Auger Assembly RHKnob Black POP RivetWasher Plastic WasherLEVER/CABLE Rotator Assembly Rotator HeadRotator Pivot Bracket Pulley PivotRepair Parts Snow Thrower - Model Number PR208 Handles Panel Bracket LH Panel Bracket RHHandle Grip Lower HandleSpacer RetainerKnob RED Handle KnobImpeller ROD Assembly Traction ROD AssemblyShifter ROD TOP Shifter ROD Bottom01.10.001-B Console PanelRepair Parts Snow Thrower - Model Number PR208 Drive Speed Selector Assembly 43 420900 Drive Plate AssemblyEND Plate Control ARMAxle Shaft Roll PIN 3/16Sprocket Clik PINKEY Part Description LCT Engine Model PLMHK18600781DP 417014X428 Engine Mount PlateImpeller Belt Belt CoverTraction Belt Repair Parts Snow Thrower - Model Number PR208 Wheels Wheel Assembly LH187831X417 187866X417Repair Parts Snow Thrower - Model Number PR208 BAG of Parts Safety Ignition KEYRetainer PIN WrenchRepair Parts Snow Thrower - Model Number PR208 Decals Service Notes Service Notes Limited Warranty