Poulan 421283 owner manual Parts Packed Separately in Carton, Assembly / PRE-OPERATION

Page 4

PARTS PACKED SEPARATELY IN CARTON

(1) AUGER CONTROL ROD

(1) TRACTION DRIVE CONTROL ROD

(1) MULTI-

WRENCH

(180684)

(2) FLAT WASHERS

 

(1) POWER CORD

 

(1) DISCHARGE CHUTE

(198563)

(3) RETAINER

 

 

 

 

 

SPRINGS

 

 

(169675)

ROTATOR HEAD MOUNTING

(2) CARRIAGE BOLTS 3/8-16 x 2.25

(1) WASHER 3/8

(1) LOCKNUT 3/8

(1) SAFTEY IGNITION KEY

(35062)

(19131316)

(73800600)

 

(2) HANDLE KNOBS

EXTRA SHEAR BOLTS AND NUTS

(2) SHEAR BOLTS 1/4-20 x 1-3/4

(2) SPACERS

(2) LOCKNUTS

(198636)

(198638)

1/4-20

 

 

(73800400)

ASSEMBLY / PRE-OPERATION

Read these instructions and this manual in its entirety

 

2.

Cut down all four corners of carton and lay panels flat.

before you attempt to assemble or operate your new

 

3.

Remove the two (2) screws securing the auger housing

snow thrower. Reading the entire manual will familiar-

 

 

 

to the pallet.

ize you with the unit, which will assist you in assembly,

 

 

 

4.

Remove all packing materials except plastic tie holding

operation and maintenance of the product.

 

 

 

speed control rod to lower handle.

Your new snow thrower has been assembled at the factory

 

 

 

5. Remove the two (2) plastic ties securing the upper

with the exception of those parts left unassembled for ship-

 

 

 

handle to the pallet.

ping purposes. All parts such as nuts, washers, bolts, etc.,

 

 

 

6. Remove snow thrower from carton and check carton

necessary to complete the assembly have been placed in

 

the parts bag. To ensure safe and proper operation of your

 

 

thoroughly for additional loose parts.

snow thrower, all parts and hardware you assemble must

 

HOW TO SET UP YOUR SNOW THROWER

be tightened securely. Use the correct tools as necessary

 

to ensure proper tightness.

 

TOOL BOX (See Fig. 8)

 

 

REMOVE SNOW THROWER FROM CARTON

 

A toolbox is provided on your snow thrower. The toolbox is

1. Remove all accessible loose parts and parts boxes

 

located on top of the belt cover. Store the extra shear bolts,

4

nuts and multi-wrench provided in parts bag in the toolbox.

from carton.

 

 

Page 3 Page 5
Image 4
Page 3 Page 5
Contents Model Number Snow ThrowerSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Assembly / PRE-OPERATION HOW to SET UP Your Snow ThrowerParts Packed Separately in Carton Remove Snow Thrower from CartonInstall Speed Control ROD See Figs Unfold Upper HandleInstall Discharge Chute / Chute Rotater Head See Fig Install Auger Control ROD See FigsCheck Tire Pressure Operation Know Your Snow ThrowerPrimer Ignition KEYMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting the engineHOW to USE Your Snow Thrower StoppingTo Throw Snow See Fig Using the CLEAN-OUT Tool See FigTo Move Forward and Backward See Fig Before Starting the Engine To Start EngineBefore Stopping Snow Throwing TipsIf Recoil Starter has Frozen Maintenance General RecommendationsBefore Each USE LubricationCleaning EngineService and Adjustments To Adjust Snow Thrower HeightChute Deflector Shear Bolts See FigTo Replace Belts See Fig Storage OtherTroubleshooting Service Notes Exploded KEY Part Description Auger Housing Scrapper BARAuger 24 LH Auger 24 RHAuger Bearing Bearing PlugChute Weldment Deflector WeldmentDeflector Seal StrapLEVER/CABLE Rotator Assembly Rotator HeadRotator Pivot Bracket Pulley PivotPanel Bracket LH Panel Bracket RH Handle GripLower Handle Pivot Support WeldmentSpacer RetainerKnob RED Handle KnobCarriage Bolt 5/16−18 X 155377 NUT 5/16−18 169675 Wire Harness Console PanelHeadlight Bezel Flood HeadlightRepair Parts Snow Thrower - Model Number PR5524ES Drive Speed Selector Assembly 43 402689 Drive Plate AssemblyEND Plate Control ARMAxle Shaft Roll PIN 3/16Sprocket Clik PINKEY Part Description Engine Tecumseh Model LH195SP-67510D 423184X428 Engine Mount PlateTraction Belt Belt CoverImpeller Belt Repair Parts Snow Thrower - Model Number PR5524ES Wheels Wheel Assembly LHPower Cord Safety Ignition KEYRetainer PIN WrenchDECAL, Danger DECAL, Poulan PRODECAL, DANGER, Deflector DECAL, InstructionService Notes Service Notes Limited Warranty
Top Page Image Contents