Poulan 96194000600 owner manual Engine, Cleaning

Page 15

MAINTENANCE

AUGER GEAR CASE

The gear case was filled with lubricant to the proper level at the factory. The only time the lubricant needs attention is if service has been performed on the gear case.

If lubricant is required, use only Ronex ED #1 grease.

TRACTION DRIVE SYSTEM

DO NOT lubricate the drive components inside the snow thrower. The sprockets, hex shafts, drive disc and friction wheel require no lubrication. The bearings and bushings are lifetime lubricated and require no maintenance.

CAUTION: Any lubricating of the above compo- nents can cause contamination of the friction wheel and damage to the drive system of your snow thrower.

ENGINE

See engine manual.

LUBRICATION

Use only high quality detergent oil rated with API service classification SG–SL. Select the oil's SAE viscosity grade according to your expected operating temperature.

NOTE: Although multi-viscosity oils (5W30, 10W30 etc.) improve starting in cold weather, these multi-viscosity oils will result in increased oil consumption when used above 32°F. Check your engine oil level more frequently to avoid possible engine damage from running low on oil.

Changetheoilafterevery25hoursofoperationoratleastonce a year if the snow thrower is not used for 25 hours in one year.

Check the crankcase oil level before starting the engine and after each five (5) hours of continuous use. Tighten oil fill cap / dipstick securely each time you check the oil level.

TO CHANGE ENGINE OIL

Determine temperature range anticipated before next oil change. All oil must meet API service classification SG–SL.

Be sure snow thrower is on level surface.

Oil will drain more freely when warm.

Catch oil in a suitable container.

NOTE: The left side wheel may be removed from snow thrower for easier access to the oil drain plug and place- ment of a suitable container. The unit tilted, resting on the frame with the left wheel removed, will help drain any oil trapped inside the engine. (See “TO REMOVE WHEELS” in the Service and Adjustments section of this manual).

1.Remove safety ignition key and disconnect spark plug wire from spark plug. Place wire where it cannot come in contact with spark plug.

2.Clean area around drain plug.

3.Remove drain plug and drain oil in a suitable container.

4.Install drain plug and tighten securely.

5.Wipe off any spilled oil from snow thrower and engine.

6.Install left wheel (if removed for draining oil). Be sure to install klick pin into proper hole in wheel axle (See “TO REMOVE WHEELS” in the Service and Adjustments section of this manual).

7.Remove oil fill cap/dipstick. Be careful not to allow dirt to enter the engine.

8.Refill engine with oil through oil dipstick tube. Pour slowly. Do not overfill. For approximate capacity see “PRODUCT SPECIFICATIONS” section of this manual.

9.Use gauge on oil fill cap/dipstick for checking level. Be sure dipstick cap is tightened securely for accurate reading. Keep oil at “FULL” line on dipstick.

10.Wipe off any spilled oil.

MUFFLER

Inspect and replace corroded muffler as it could create a fire hazard and/or damage.

SPARK PLUG

Replace spark plug at the beginning of each season or after every 100 hours of operation, whichever occurs first. Spark plug type and gap setting are shown in the “PRODUCT SPECIFICATIONS” section of this manual.

CLEANING

IMPORTANT: For best performance, keep snow thrower housing free of any dirt or trash. Clean the outside of your snow thrower after each use.

WARNING: Remove safety ignition key and disconnect spark plug wire from spark plug. Place wire where it cannot come in contact with spark plug.

Keep finished surfaces/wheels free of gasoline, oil, etc.

We do not recommend using a garden hose to clean your snow thrower unless the electrical system, muffler and carburetor are covered to keep water out. Water in engine can result in shortened engine life.

15

Image 15
Contents Snow Thrower Model NumberSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Unfold Upper Handle Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Remove Snow Thrower from CartonInstall Auger Control ROD See Figs Install Traction Drive Control ROD See FigsInstall Discharge Chute / Chute Rotator Head See Fig Install Chute Deflector Remote Control See FigsCheck Tire Pressure Ignition KEY OperationKnow Your Snow Thrower PrimerMeets A.N.S.I. Safety Requirements Stopping HOW to USE Your Snow ThrowerTo Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig To Throw Snow See FigBefore Starting the Engine If Recoil Starter has Frozen Snow Throwing TipsTo Start Engine Before StoppingMaintenance Engine CleaningShear Bolts See Fig Service and AdjustmentsTo Adjust Snow Thrower Height Chute DeflectorTo Replace Belts See Fig Storage Other Troubleshooting¡ATENCIÓN! ¡ESTE ALERTO! SU Seguridad Esta Comprometida PreparaciónFuncionamiento Montaje / PRE-OPERACIÓN Partes Empacadas POR Separado EL LA Caja DE Cartón Desplegar LA Empuñadura Superior Montaje / PRE-OPERACIÓNSacar LA Máquina Quitanieves DEL Cartón Como Preparar SU Máquina QuitanievesMontaje DE LA Biela DE Mando DE LA Tracción Ver Figs yDE Mando DE LA Barrena Ver Figs y Controlar LA Presión DE LOS Neumáticos Familiarícese CON SU Máquina Quitanieves OperaciónCumple CON LOS Requisitos DE Seguridad DE LA A.N.S.I Controlar LA Eyección DE LA Nieve Como Utilizar SU Máquina QuitanievesPararse Funcionamiento DE LA Dirección Ver Fig Lanzar LA Nieve Ver FigUsar LA Herramienta Para Limpiar Ver Fig Moverse Adelante Y Atrás Ver FigControlar EL Nivel DE Aceite DEL Motor Ver Fig Antes DE Poner EN Marcha EL MotorRegular LAS Placas DE Deslizamiento Ver Fig Barra DE Arrastre Ver FigSI EL Arrancador DE Retroceso SE HA Congelado Consejos Para Lanzar LA NievePuesta EN Marcha DEL Motor Antes DE PararMantenamiento Recomendaciones GeneralesLubricación Limpieza Pernos DE Seguridad Ver Fig Servicio Y AdjustesPara Ajustar LA Altura DE Máquina Quitanieves Conducto DeflectorVaciar LA Gasolina DEL Depósito DE Carburante Sustituir LAS Correas Vea FigAlmacenimiento MotorOtros Identificacion DE Problemas Page KEY Part Description Page 414280 Knob, Lever Repair Parts Snow Thrower Model Number Handles Repair Parts Snow Thrower Model Number 96194000600 Handles Repair Parts Snow Thrower Model Number 96194000600 Drive Repair Parts Snow Thrower Model Number 96194000600 Drive Page KEY Part Description Repair Parts Snow Thrower Model Number 96194000600 Wheels KEY Part Description Repair Parts Snow Thrower Model Number 96194000600 Decals 181038 Decal, Danger Limited Warranty

96194000600 specifications

The Poulan 96194000600 is a standout lawn mower that exemplifies quality and innovation in outdoor power equipment. Designed to meet the diverse needs of homeowners and landscape enthusiasts, this mower combines advanced features and technologies to deliver impressive performance and ease of use.

One of the main features of the Poulan 96194000600 is its powerful engine. Equipped with a reliable gas engine, it provides robust power for mowing various types of grass and terrain. This ensures that even tougher lawns are tackled efficiently, allowing homeowners to achieve that well-manicured look with minimal effort.

The mower is designed with a wide cutting deck, typically measuring around 21 inches. This size not only enhances the mower’s ability to cover more ground in less time but also provides a clean and even cut. The adjustable cutting height feature allows users to select the optimal height for their lawn, catering to different grass types and individual preferences.

In terms of technology, the Poulan 96194000600 incorporates a self-propulsion system. This feature significantly reduces the amount of effort required to push the mower, making it easier to navigate hilly or uneven terrain. With variable speed control, users can adjust the pace of the mower to suit their walking speed, enhancing comfort and control during operation.

Durability is another hallmark of the Poulan 96194000600. Constructed with rugged materials, this mower is built to withstand the rigors of regular use. Its solid frame and high-quality blades are designed for longevity, ensuring that owners can rely on this equipment season after season.

User convenience is a priority in the design of the Poulan 96194000600. The mower features ergonomic handles, enhancing comfort during operation. Additionally, it often includes features such as tool-free height adjustments and easy-to-empty grass bags, streamlining the maintenance process.

With its combination of power, versatility, and user-friendly design, the Poulan 96194000600 is an ideal choice for those seeking a dependable lawn mower. Whether you have a small yard or a larger garden, this mower promises to deliver exceptional performance, making lawn care a more enjoyable and efficient task.