Poulan PP11530ES owner manual Storage, Other

Page 18

SERVICE AND ADJUSTMENTS

KLIK PIN (INSTALL

OUTER HOLE

IN OUTER HOLE

 

OF AXLE ONLY)

 

 

AXLE

WHEEL

WHEEL HUB

ENGINE

FIG. 25

 

See engine manual.

 

CARBURETOR

Your carburetor is not adjustable. Engine performance should not be affected at altitudes up to 7,000 feet (2,134 meters). If your engine does not operate properly due to suspected carburetor problems, take your snow thrower to a qualified service center.

ENGINE SPEED

Never tamper with the engine governor, which is factory set for proper engine speed. Overspeeding the engine above the factory high speed setting can be dangerous and will void the warranty. If you think the engine-governed high speed needs adjusting, contact a qualified service center, which has proper equipment and experience to make any necessary adjustments.

STORAGE

Immediately prepare your unit for storage at the end of the season or if the unit will not be used for 30 days or more.

WARNING: Never store the snow thrower with gasoline in the tank inside a building where fumes may reach an open flame, spark or pilot light as on a furnace, water heater, clothes dryer or gas appliance. Allow the engine to cool before storing in any enclosure.

SNOW THROWER

When snow thrower is to be stored for a period of time, clean it thoroughly, remove all dirt, grease, leaves, etc. Store in a clean, dry area.

1.Clean entire snow thrower (See “CLEANING” in the Maintenance section of this manual).

2.Inspect and replace belts, if necessary (See “TO RE- PLACE BELTS” in the Service and Adjustments section of this manual).

3.Lubricate as shown in the Maintenance section of this manual.

4.Be sure that all nuts, bolts, screws, and pins are securely fastened. Inspect moving parts for damage, breakage and wear. Replace if necessary.

5.Touch up all rusted or chipped paint surfaces; sand lightly before painting.

ENGINE

See engine manual.

FUEL SYSTEM

IMPORTANT: It is important to prevent gum deposits from forming in essential fuel system parts such as carburetor, fuel hose, or tank during storage. Also, alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage.

•Empty the fuel tank by starting the engine and letting it run until the fuel lines and carburetor are empty.

•Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

•Use fresh fuel next season.

NOTE: Fuel stabilizer is an acceptable alternative in min- imizing the formation of fuel gum deposits during storage. Add stabilizer to gasoline in fuel tank or storage container. Always follow the mix ratio found on stabilizer container. Run engine at least 10 minutes after adding stabilizer to allow the stabilizer to reach the carburetor. Do not drain the gas tank and carburetor if using fuel stabilizer.

ENGINE OIL

Drain oil (with engine warm) and replace with clean en- gine oil. (See “ENGINE” in the Maintenance section of this manual).

CYLINDER

1.Remove spark plug.

2.Pour one ounce (29 ml) of oil through spark plug hole into cylinder.

3.Pull recoil starter handle slowly a few times to distribute oil.

4.Replace with new spark plug.

OTHER

•Remove safety ignition key; store it in a safe place.

•Do not store gasoline from one season to another.

•Replace your gasoline can if your can starts to rust. Rust and/or dirt in your gasoline will cause problems.

•If possible, store your snow thrower indoors and cover it to protect it from dust and dirt.

•Cover your snow thrower with a suitable protective cover that does not retain moisture. Do not use plastic. Plastic cannot breathe, which allows condensation to form and will cause your snow thrower to rust.

IMPORTANT: Never cover snow thrower while engine/ exhaust area is still warm.

18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Model Number Snow ThrowerSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Remove Snow Thrower from Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Unfold Upper HandleInstall Traction Drive Control ROD See Figs Install Auger Control ROD See FigsInstall Discharge Chute / Chute Rotator Head See Fig Install Chute Deflector Remote Control See FigsCheck Tire Pressure Primer OperationKnow Your Snow Thrower Ignition KEYMeets A.N.S.I. Safety Requirements Deflector remote control lever used to changeHOW to USE Your Snow Thrower StoppingTo Adjust Skid Plates See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig To Throw Snow See FigCheck Engine OIL Level See Fig Before Starting the EngineScraper BAR ADD Gasoline See FigBefore Stopping Snow Throwing TipsTo Start Engine If Recoil Starter has FrozenMaintenance Cleaning EngineService and Adjustments To Adjust Snow Thrower HeightChute Deflector To Remove Wheels See Fig Remove the klik pin and remove wheel from axleStorage OtherTroubleshooting 2220 KEY Part Description Page 414280 Knob, Lever Repair Parts Snow Thrower Model PP11530ES Handles Repair Parts Snow Thrower Model PP11530ES Handles Repair Parts Drive Repair Parts Snow Thrower Model PP11530ES Drive Page KEY Part Description 417014X428Repair Parts Snow Thrower Model PP11530ES Wheels / Decals Repair Parts Limited Warranty

PP11530ES specifications

The Poulan PP11530ES is a powerful and efficient gas chainsaw designed for both professional and casual users. With its robust engine and innovative features, it stands out as a reliable tool for tackling a variety of cutting tasks, from firewood preparation to storm cleanup and tree pruning.

One of the primary characteristics of the PP11530ES is its 50cc two-stroke engine, providing ample power for cutting through thick branches and logs with ease. The engine is engineered with efficiency in mind, offering a balance of performance and fuel economy that ensures longer operation times between refueling. The chainsaw is equipped with a quick start technology, making it easier to start with minimal effort, an essential feature that saves time and energy during use.

Comfort and control are paramount in the design of the Poulan PP11530ES. It features an ergonomic handle that enhances grip and allows for comfortable operation over extended periods. The saw is also equipped with an anti-vibration system, which helps to reduce fatigue while minimizing the impact of vibrations on the user’s hands and arms. This feature is particularly beneficial for those who need to use a chainsaw for prolonged periods.

The PP11530ES comes with a 16-inch bar and chain length, ideal for small to medium-sized cutting tasks. The bar length offers versatility, allowing users to cut through various sizes of wood while still being manageable for novice users. The automatic oiling system ensures that the chain remains lubricated during operation, promoting better performance and extending the life of the chainsaw.

Safety is another critical aspect of the Poulan PP11530ES. The chainsaw is equipped with a chain brake that instantly stops the chain’s movement in case of kickback, reducing the risk of accidents. Additionally, the saw has a handguard that protects the user from debris and the chain while in operation.

The Poulan PP11530ES also features an easy-access air filter and spark plug, simplifying maintenance and ensuring that the chainsaw operates efficiently over time. Overall, this chainsaw blends power, user-friendly features, and safety, making it an excellent choice for anyone looking to tackle outdoor cutting tasks with confidence and ease. Its combination of performance-enhancing technologies and practical design elements positions the PP11530ES as a reliable companion for all your cutting needs.
Top Page Image Contents