Poulan PP8527ESB owner manual Snow Throwing Tips, Before Stopping, If Recoil Starter has Frozen

Page 13

OPERATION

COLD START - ELECTRIC STARTER

1.Insert safety ignition key into the ignition slot until it clicks. DO NOT turn the key. Keep the extra safety ignition key in a safe place.

2.Place throttle control in FAST position.

3.Rotate choke control to FULL position.

4.Connect the power cord to the engine.

5.Plug the other end of the power cord into a three-hole grounded 120 Volt A.C. receptacle.

NOTE: Do not use primer when starting engine with the electric starter.

6. Push starter button until engine starts.

IMPORTANT: Do not crank engine more than fi ve con- tinuous seconds between each time you try to start. Wait 5 to 10 seconds between each attempt.

7.When the engine starts, release the starter button and slowly move the choke control to the OFF position.

8.Disconnect the power cord from the receptacle fi rst, then from the engine.

Allow the engine to warm up for a few minutes. Engine will not develop full power until it has reached normal operating temperature.

WARM START - ELECTRIC STARTER

Follow the steps above, keeping the choke control in the OFF position.

COLD START - RECOIL STARTER

1.Insert safety ignition key into the ignition slot until it clicks. DO NOT turn the key. Keep the extra safety ignition key in a safe place.

2.Place throttle control in FAST position.

3.Rotate choke control to FULL position.

4.Push the primer four (4) times if the temperature is below 15°F, or two (2) times if temperature is between 15° and 50°F. If temperature is above 50°F, priming is not necessary.

NOTE: Over priming may cause fl ooding, preventing the engine from starting. If you do fl ood the engine, wait a few minutes before attempting to start and DO NOT push the primer.

5.Pull recoil starter handle quickly. Do not allow starter rope to snap back.

6.When the engine starts, release the recoil starter handle and slowly move the choke control to the OFF position.

Allow the engine to warm up for a few minutes. Engine will not develop full power until it has reached normal operating temperature.

WARM START - RECOIL STARTER

Follow the steps above, keeping the choke in the OFF position. DO NOT push the primer.

BEFORE STOPPING

Run the engine for a few minutes to help dry off any mois- ture on the engine.

To avoid possible freeze-up of the starter, proceed as fol- lows:

13

ELECTRIC STARTER

1.Connect the power cord to the engine.

2.Plug the other end of the power cord into a three-hole grounded 120 Volt A.C. receptacle.

3.While the engine is running, push starter button and spin the starter for several seconds.

NOTE: The unusual sound made while starter is spinning will not harm the engine or starter.

4.Disconnect the power cord from the receptacle fi rst, then from the engine.

RECOIL STARTER

1.While the engine is running, pull the recoil starter handle with rapid, full arm strokes three or four times.

NOTE: The unusual sound made while pulling the recoil starter handle will not harm the engine or starter.

IF RECOIL STARTER HAS FROZEN

If the recoil starter has frozen and will not turn the engine, proceed as follows:

1.Grasp the recoil starter handle and slowly pull as much rope out of the starter as possible.

2.Release the recoil starter handle and let it snap back against the starter.

If the engine still fails to start, repeat the above steps or use the electric starter.

SNOW THROWING TIPS

•Always operate the snow thrower with the engine at full throttle. Full throttle offers the best performance.

•Go slower in deep, freezing or heavy wet snow. Use the drive speed control, NOT the throttle, to adjust speed.

•It is easier and more effi cient to remove snow imme- diately after it falls.

•The best time to remove snow is the early morning. At this time the snow is usually dry and has not been ex- posed to the direct sun and warming temperatures.

•Slightly overlap each successive path to ensure all snow will be removed.

•Throw snow downwind whenever possible.

•Adjust the skid plates to proper height for current snow conditions. See “TO ADJUST SKID PLATES” in this section of this manual.

•For extremely heavy snow, reduce the width of snow removal by overlapping previous path and moving slowly.

•Keep engine clean and clear of snow during use. This will help air fl ow and extend engine life.

•After snow-throwing is completed, allow engine to run for a few minutes to melt snow and ice off the engine.

•Clean the entire snow thrower thoroughly after each use and wipe dry so it is ready for next use.

WARNING: Do not operate snow thrower if weather conditions impair vis- ibility. Throwing snow during a heavy, windy snowstorm can blind you and be hazardous to the safe operation of the snow thrower.

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Snow Thrower Model NumberPreparation TrainingOperation Static Electricity HazardAPI-SF-SJ Maintenance and StorageParts Packed Separately in Carton Service and Adjustments14-15 16-18HOW to SET UP Your Snow Thrower Assembly / PRE-OPERATIONRemove Snow Thrower from Carton Unfold Upper HandleInstall Auger Control ROD See Figs Install Traction Drive Control ROD See FigsCheck Tire Pressure Install Discharge Chute / Chute Rotater Head See FigKnow Your Snow Thrower OperationRecoil auxiliary starter handle used for starting the engine Meets A.N.S.I. Safety RequirementsStopping HOW to USE Your Snow ThrowerTo Move Forward and Backward See Fig To Throw Snow See FigScraper BAR Before Starting the EngineTo Start Engine Before Stopping Snow Throwing TipsIf Recoil Starter has Frozen General Recommendations MaintenanceBefore Each USE LubricationEngine CleaningTo Adjust Snow Thrower Height Service and AdjustmentsChute Deflector Shear Bolts See FigTo Replace Belts See Fig Other StorageTroubleshooting Limited Warranty

PP8527ESB specifications

The Poulan PP8527ESB is a powerful and versatile chainsaw ideal for both casual users and professionals tackling demanding tasks. This model is particularly recognized for its robust performance and user-friendly features, making it a popular choice among outdoor enthusiasts and those in need of reliable cutting equipment.

One of the standout features of the PP8527ESB is its 27cc engine, which delivers an impressive balance of power and efficiency. The engine is designed to provide ample cutting force, allowing users to easily handle a variety of cutting tasks, whether it's pruning branches, cutting firewood, or felling small trees. The chainsaw is equipped with a 16-inch bar and chain, striking a perfect balance between cutting capacity and weight, which enhances maneuverability and control.

Safety is a top priority with the Poulan PP8527ESB, and this model includes several safety features designed to protect the user during operation. It features a safety chain brake that engages when kickback occurs, helping to prevent accidents and injuries. Additionally, the chainsaw incorporates an automatic oiler, which ensures the bar and chain receive adequate lubrication, extending the life of these components and maintaining optimal performance.

Another noteworthy aspect of the PP8527ESB is its lightweight design. Weighing in at around 10 pounds, this chainsaw is easy to handle, making it ideal for extended use without causing excessive fatigue. The ergonomic handle design ensures comfort during operation, allowing users to work for longer periods with minimal strain.

Technologically, the Poulan PP8527ESB incorporates Easy Start technology, facilitating effortless starting with minimal pulling effort. This feature is particularly beneficial for users who may struggle with traditional starting methods. The chainsaw also boasts a tool-less air filter and spark plug access, simplifying maintenance and ensuring the unit remains in peak operating condition.

In conclusion, the Poulan PP8527ESB chainsaw is a robust, user-friendly tool that combines power, safety, and ease of use. With its efficient 27cc engine, safety features, lightweight design, and innovative technologies, it stands out as an excellent choice for both home gardeners and professionals alike, ensuring that users can tackle a wide range of cutting tasks with confidence.
Top Page Image Contents