MTD 31AE993I401 Operating Your Snow Thrower, Before Starting, Gas & Oil Fill-Up, To Start Engine

Page 9

Chute Crank

The chute crank is located on the left side of the snow thrower. Use it to change the direction in which snow is thrown. Avoid targetting persons, animals or cars and buildings.

CLOCKWISE TO DISCHARGE LEFT

COUNTER CLOCKWISE TO DISCHARGE RIGHT

Skid Shoe

The skid shoe position is determined by the condition of the ground from where snow has to be removed. Higher the snow level, lower will be the skid shoe. Adjust it accordingly.

Headlight

Chute Tilt Control

The distance snow is thrown can be changed by adjusting the angle of the chute assembly. Move the chute tilt control forward to decrease the distance, toward the rear to increase.

Wheel Steering Controls

The left and right wheel steering controls are located on the underside of the handles. See .

•Squeeze the right control to turn right; squeeze the left control to turn left.

NOTE: Operate the snow thrower in open areas until you are familiar with these controls.

The headlight is on whenever the engine is running.

Throttle Control

The throttle control is located on the engine. It regulates the speed of the engine.

Safety Ignition Key

The safety ignition key must be fully inserted in the switch before the unit will start. Remove key when snow thrower is not in use. Do not attempt to turn the key.

Chute Clean-Out Tool

The chute clean-out tool is designed to clear a clogged discharge chute. Refer to page 11 for instructions on how to properly use it.

WARNING: Never use your hand to clear a clogged discharge chute. Shut off engine and remain behind handles until all moving parts have stopped before unclogging.

SECTION 4: OPERATING YOUR SNOW THROWER

Before Starting

Read and understand all instructions and warnings on the machine and in this manual before operating.

Gas & Oil Fill-Up

•Service the engine with gasoline and oil as instructed in the engine manual shipped with the snow thrower.

WARNING: Use extreme care when handling gasoline. Gasoline is extremely flammable and the vapors are explosive. Never fuel machine indoors or while the engine is hot or running. Extinguish cigarettes, cigars, pipes an other sources of ignition.

To Start Engine

NOTE: If unit shows any sign of motion (drive or augers) with the clutch grips disengaged, shut engine off immediately. Readjust as instructed in the Final Adjustments in the Assembly Section.

•Attach spark plug wire to spark plug.

•Make certain the auger and drive clutch levers are in the disengaged (released) position.

•Move throttle control up to FAST position.

•Insert ignition key into slot. Be certain it snaps into place. Do not turn key.

NOTE: Engine will not start unless ignition key is inserted into ignition slot in carburetor cover.

•A plastic cap is provided inside the fuel fill opening on the fuel tank. Remove and discard this cap before filling up the tank. Use the proper fuel tank cap to close after fill-up.

Electric Starter

WARNING: The electric starter is equipped with a grounded three-wire power cord and plug and is designed to operate on 120 volt AC household current. It must be used with a properly grounded three-prong receptacle at all times to avoid the possibility of electric shock. Follow all instructions carefully prior to operating the electric starter.

9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents MTD LLC, P.O. BOX 361131 CLEVELAND, Ohio Operator’s ManualTable of Contents Training Important Safe Operation PracticesPreparation OperationYour Responsibility Maintenance & StorageAssembling Your Snow Thrower Final Adjustments Chute Clean-Out ToolTraction Control & Shift Lever Auger ControlTire Pressure Pneumatic Tires Traction Control / Auger Control Lock Knowing Your Snow ThrowerShift Lever Discharge ChuteBefore Starting Operating Your Snow ThrowerGas & Oil Fill-Up To Start EngineTo Engage Wheel Drive To Stop EngineTo Engage Augers Operating TipsTraction Control Shift RodMaintaining Your Snow Thrower Gear Case Gear ShaftAuger Shaft Auger Bearings and ShaftServicing Your Snow Thrower Auger Belt Replacing BeltsDrive Belt Changing Friction Wheel RubberSprocket Hex Shaft Hex Hub Safety & Decorative Labels Part Number and LocationProblem Cause Remedy TroubleshootingDescription Parts List for ModelModel Part Description List Color Codes below Please add Model 20 57 05244A Bearing Housing Model Description MTD LLC, P.O. BOX 361131 CLEVELAND, Ohio 44136-0019 Phone MANUFACTURER’S Limited Warranty for

31AE993I401 specifications

The MTD 31AE993I401 is a powerful riding lawn mower designed to deliver an efficient and reliable lawn care experience. This machine is tailored for homeowners looking for a robust and easy-to-use solution for maintaining their yards. With its practical features and advanced technologies, the MTD 31AE993I401 stands out in the competitive landscaping market.

One of the most notable features of the MTD 31AE993I401 is its impressive 18 HP engine, which provides ample power to tackle challenging terrains and dense grass. The engine is designed for efficiency, ensuring that users can complete their mowing tasks without frequently refueling. The mower's hydrostatic transmission allows for smooth and seamless acceleration, enabling operators to adjust their speed effortlessly while maneuvering around obstacles.

The cutting deck is another defining characteristic of the MTD 31AE993I401. With a wide 42-inch cutting width, the mower covers a larger area in fewer passes, making it ideal for medium to large lawns. The deck height adjustment feature offers versatility, allowing users to customize the cutting height to suit their lawn’s specific needs. This is particularly beneficial for maintaining a healthy grass height that promotes optimal growth.

Comfort is a priority in the design of the MTD 31AE993I401. It features an ergonomic seat with armrests, providing users with a comfortable riding experience, even during extended mowing sessions. The intuitive control panel ensures that all essential functions are easily accessible, making operation straightforward for both new and experienced users.

To enhance durability and longevity, the MTD 31AE993I401 is built with robust, high-quality materials. Its steel frame adds to its resilience, ensuring the mower can withstand the rigors of regular use.

Additionally, the MTD 31AE993I401 incorporates innovative technologies for ease of use and maintenance. The mower is equipped with a reliable starting system, reducing the hassle of manual start-ups. Its easy-to-reach maintenance points simplify service tasks, making it easier for owners to keep the mower in prime condition.

In summary, the MTD 31AE993I401 riding lawn mower combines power, comfort, and durability into a single machine. Its efficient engine, wide cutting deck, and user-friendly features make it a top choice for those seeking an effective lawn care solution. Whether you're tackling a small yard or managing expansive lawns, the MTD 31AE993I401 delivers exceptional performance and reliability.
Top Page Image Contents