Snapper I55224, I7244 important safety instructions Maintenance and Storage

Page 3

IMPORTANT SAFETY INSTRUCTIONS

OPERATIONAL PRECAUTIONS

(Continued From Previous Page)

7.DO NOT put hands or feet near or under rotating parts. Keep clear of the discharge opening at all times.

8.Start engine only where exhaust fumes will be safely dissipated. Allow a brief warm-up period, and practice operation of controls outside before putting the machine to work.

9.After striking a foreign object, STOP the engine (motor), remove the key, and remove the wire from spark plug. Thoroughly inspect the snow thrower for any damage, and repair the damage before restarting and operating the snow thrower.

10.STOP the engine if the machine starts to vibrate excessively as this normally indicates mechanical problems. Remove the key and disconnect the spark plug wire to prevent unintentional starting before servicing or repairing the machine.

11.DO NOT clear snow across the face of slopes. Exercise extreme CAUTION when changing direction on slopes. DO NOT attempt to clear steep slopes.

12.DO NOT leave machine unattended with the engine running. STOP engine and remove key to prevent unauthorized operation.

13.Release clutch control and make sure auger/impeller has STOPPED before adjusting deflector, or placing hands near auger/impeller.

14.DO NOT use snow thrower on surfaces above ground level, such as, a roof of a building.

15.Exercise extreme CAUTION when operating on or crossing gravel drives, walks, or roads. Stay alert for hidden hazards or traffic.

16.DO NOT overload the machine capacity by attempting to clear snow at too fast a rate.

17.Never operate the machine at high transport speeds on slippery surfaces. Look behind and use care when backing.

18.Disengage power to the auger/impeller when snow thrower is transported or not in use.

19.Use only attachments and accessories approved by the manufacturer of the snow

thrower (such as wheels weights, counterweights, cabs and the like).

20.Never operate the snow thrower without good visibility or light. Always be sure of your footing, and keep a firm hold on the handles. Walk; never run.

MAINTENANCE AND STORAGE

1.DO NOT store machine or fuel container inside where fumes may reach an open flame, spark, or pilot light as in a water heater, furnace, clothes dryer or other gas appliance. Allow engine to cool before storing machine in an enclosure. Store fuel container out of reach of children in a well ventilated, unoccupied building.

2.Keep machine and engine free of excess oil, grease and spilled fuel to reduce fire hazard.

3.When draining fuel tank, drain fuel into an approved container outdoors and away from open flame.

4.Inspect all bolts, nuts and screws frequently and keep properly tightened.

5.Use only recommended shear bolts (if equipped) to prevent possible damage to machine.

6.Service engine and make adjustments only when engine is stopped. Remove key, remove wire from spark plug, secure wire away from plug, and disconnect cord from electric starting motors to prevent accidental starting.

7.DO NOT change engine governor speed settings or overspeed engine.

8.DO NOT test for spark by grounding the spark plug next to spark plug hole. Spark from the plug could ignite gas exiting engine.

9.Have machine serviced by an authorized SNAPPER dealer at least once a year and have the dealer install any new safety devices.

10.Use only genuine SNAPPER replacement parts to assure that original standards are maintained.

3

Image 3
Contents Model Number Explanation Model Designation Series Designation Engine HP Auger WidthInstruction No -4330 I.R /11/01 Operational Precautions Protection for ChildrenPreparation Maintenance and Storage Table of Contents PRE-START Check List Minimum Gauge for Cord SetsGo to Page 8 for Electric Start Models 2.2.1. Engine STARTING, Operation & Stopping Recoil Start ModelsEngaging Auger Engaging Wheel DriveStopping ENGINE, Auger & Wheel Drive STARTING, Operation & Stopping Electric Start Models Adjustment General Lubrication Service After First 5 Hours Check Auger Drive BeltIntroduction Check Wheel Drive BeltStorage Procedure Annually END of Each SeasonEngine Spark Plug Auger and Wheel Drive Cable Auger Belt Idler Pulley AdjustmentFrom Previous Auger Belt ReplacementRepair & Adjustments Ground Speed Adjustment Skid Shoe Adjustment1st 4th Single Handle Control Adjustment 7 HP Models Only Rubber Drive Tire Replacement Chute Crank Adjustment100 Problem Probable Cause Corrective ActionService Performed Each Adjustment Tires Check Air PressureDisclaimer of Warranty Year Limited WarrantyTWO Stage Intermediate Frame Snow Thrower Series