Poulan 199600 owner manual Storage, Other

Page 18

SERVICE AND ADJUSTMENTS

ENGINE

See engine manual.

CARBURETOR

Your carburetor is not adjustable. Engine performance should not be affected at altitudes up to 7,000 feet (2,134 meters). If your engine does not operate properly due to suspected carburetor problems, take your snow thrower to a qualified service center.

ENGINE SPEED

Never tamper with the engine governor, which is factory set for proper engine speed. Overspeeding the engine above the factory high speed setting can be dangerous and will void the warranty. If you think the engine-governed high speed needs adjusting, contact a qualified service center, which has proper equipment and experience to make any necessary adjustments.

STORAGE

Immediately prepare your unit for storage at the end of the season or if the unit will not be used for 30 days or more.

WARNING: Never store the snow thrower with gasoline in the tank inside a building where fumes may reach an open flame, spark or pilot light as on a furnace, water heater, clothes dryer or gas appliance. Allow the engine to cool before storing in any enclosure.

SNOW THROWER

When snow thrower is to be stored for a period of time, clean it thoroughly, remove all dirt, grease, leaves, etc. Store in a clean, dry area.

1.Clean entire snow thrower (See “CLEANING” in the Maintenance section of this manual).

2.Inspect and replace belts, if necessary (See “TO RE- PLACE BELTS” in the Service and Adjustments section of this manual).

3.Lubricate as shown in the Maintenance section of this manual.

4.Be sure that all nuts, bolts, screws, and pins are securely fastened. Inspect moving parts for damage, breakage and wear. Replace if necessary.

5.Touch up all rusted or chipped paint surfaces; sand lightly before painting.

ENGINE

See engine manual.

FUEL SYSTEM

IMPORTANT: It is important to prevent gum deposits from forming in essential fuel system parts such as carburetor, fuel hose, or tank during storage. Also, alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage.

•Empty the fuel tank by starting the engine and letting it run until the fuel lines and carburetor are empty.

•Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

•Use fresh fuel next season.

NOTE: Fuel stabilizer is an acceptable alternative in min- imizing the formation of fuel gum deposits during storage. Add stabilizer to gasoline in fuel tank or storage container. Always follow the mix ratio found on stabilizer container. Run engine at least 10 minutes after adding stabilizer to allow the stabilizer to reach the carburetor. Do not drain the gas tank and carburetor if using fuel stabilizer.

ENGINE OIL

Drain oil (with engine warm) and replace with clean en- gine oil. (See “ENGINE” in the Maintenance section of this manual).

CYLINDER

1.Remove spark plug.

2.Pour one ounce (29 ml) of oil through spark plug hole into cylinder.

3.Pull recoil starter handle slowly a few times to distribute oil.

4.Replace with new spark plug.

OTHER

•Do not store gasoline from one season to another.

•Replace your gasoline can if your can starts to rust. Rust and/or dirt in your gasoline will cause problems.

•If possible, store your snow thrower indoors and cover it to protect it from dust and dirt.

•Cover your snow thrower with a suitable protective cover that does not retain moisture. Do not use plastic. Plastic cannot breathe, which allows condensation to form and will cause your snow thrower to rust.

IMPORTANT: Never cover snow thrower while engine/ exhaust area is still warm.

18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Model Number Snow ThrowerSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Remove Snow Thrower from Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Unfold Upper HandleInstall Traction Drive Control ROD See Figs Install Auger Control ROD See FigsInstall Discharge Chute / Chute Rotater Head See Fig Install Chute Deflector Remote Control See FigsCheck Tire Pressure Primer OperationKnow Your Snow Thrower Ignition KEYMeets A.N.S.I. Safety Requirements Deflector remote control lever used to changeHOW to USE Your Snow Thrower StoppingTo Throw Snow See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig To Move Forward and Backward See FigBefore Starting the Engine Scraper BARTo Start Engine Snow Throwing Tips Before StoppingIf Recoil Starter has Frozen Maintenance Cleaning EngineService and Adjustments To Adjust Snow Thrower HeightChute Deflector To Remove Wheels See Fig Remove the klik pin and remove wheel from axleStorage OtherTroubleshooting Limited Warranty

199600 specifications

The Poulan 199600 is a robust chainsaw designed for both professional landscapers and homeowners seeking powerful performance with user-friendly features. Known for its reliability, this tool is well-suited for a variety of cutting tasks, making it a versatile addition to any outdoor equipment arsenal.

At the heart of the Poulan 199600 is its high-performance engine. The chainsaw typically boasts a powerful two-stroke engine, delivering ample horsepower to handle tougher jobs like felling trees and cutting dense wood. This engine design is not only efficient but also lightweight, enhancing maneuverability while reducing user fatigue during extended use.

One of the standout features of the Poulan 199600 is its Easy Start technology. This innovative system simplifies the starting procedure, allowing users to start the chainsaw with minimal effort. This is particularly beneficial for those who may struggle with traditional pull-start chainsaws, making it accessible to a broader range of users.

Safety is a paramount concern with any chainsaw, and the Poulan 199600 incorporates several safety features to protect the operator. It includes a chain brake, which stops the chain immediately in the event of kickback, a common hazard when working with chainsaws. Additionally, the chainsaw is designed with an anti-vibration system that minimizes user fatigue, enabling more precise cutting and enhancing overall comfort during operation.

The Poulan 199600 also features an adjustable chain oiling system, allowing the user to control the lubrication of the chain for optimal performance. This feature is essential for maintaining chain longevity and ensuring smooth cutting action. The chainsaw’s durability is further enhanced by a metal spike bumper that allows for better control when cutting and helps absorb the impacts encountered during tough cutting jobs.

For ease of maintenance, the Poulan 199600 is designed with a tool-less chain tensioning system. This allows users to easily adjust the chain tension without the need for additional tools, saving time and increasing efficiency. Coupled with easy-access air filters, regular maintenance is straightforward, ensuring that the chainsaw performs optimally over time.

Overall, the Poulan 199600 offers a blend of power, safety, and convenience, making it a reliable choice for anyone in need of a sturdy chainsaw for residential or light commercial use. Whether trimming branches, cutting firewood, or tackling larger landscaping projects, the Poulan 199600 stands out as a capable and user-friendly tool that meets the needs of a diverse range of users.
Top Page Image Contents