Poulan 189645 owner manual Before Starting the Engine, Scraper BAR, To Start Engine

Page 12

OPERATION

TO ADJUST SKID PLATES (See Fig. 16)

NOTE: The wrench provided in your parts bag may be used to adjust the skid plates.

Skid plates are located on each side of the auger housing and adjust the clearance between the scraper bar and the ground surface. Adjust skid plates evenly to proper height for current surface conditions. For removal of snow in normal conditions, such as a paved driveway or sidewalk, place skid plates in the highest position (lowest scraper clearance) to give a 1/8" clearance between the scraper bar and the ground. Use a middle position if the surface to be cleared is uneven.

NOTE: It is not recommended to operate the snow thrower over gravel or rocky surfaces. Objects such as gravel, rocks or other debris, can easily be picked up and thrown by the impeller, which can cause serious personal injury, property damage or damage to the snow thrower.

•If snow thrower must be operated over gravel surface, use extra caution and be sure skid plates are adjusted to lowest (highest scraper clearance) position.

1.Shut off engine and wait for all moving parts to stop.

2.Adjust skid plates by loosening the rear 1/2" hex nut only, then moving skid plate to desired position.Be sure both plates are adjusted evenly. Tighten securely.

HIGH POSITION (LOW GROUND CLEARANCE)

AUGER

HOUSING

SKID PLATE

1/2" HEX NUT

LOW POSITION (HIGH GROUND CLEARANCE)

FIG. 16

SCRAPER BAR

The scraper bar is not adjustable, but is reversible. After considerable use it may become worn. When it has worn almost to the edge of the housing, it can be reversed, providing additional service before requiring replacement. Replace a damaged or worn scraper bar.

BEFORE STARTING THE ENGINE

CHECK ENGINE OIL LEVEL (See Fig. 17)

The engine on your snow thrower has been shipped, from the factory, already fi lled with oil.

1.Check engine oil with snow thrower on level ground.

2.Remove oil fi ll cap/dipstick and wipe clean, reinsert the dipstick and screw tight, wait for a few seconds, remove and read oil level. If necessary, add oil until “FULL” mark on dipstick is reached. Do not overfi ll.

•To change engine oil, see “TO CHANGE ENGINE OIL” in the Maintenance section of this manual.

ADD GASOLINE (See Fig. 17)

•Fill fuel tank to bottom of tank fi ller neck. Do not over- fi ll. Use fresh, clean, regular unleaded gasoline with a minimum of 87 octane. Do not mix oil with gasoline. Purchase fuel in quantities that can be used within 30

days to assure fuel freshness.

12

WARNING: Wipe off any spilled oil or fuel. Do not store, spill or use gasoline near an open flame.

CAUTION: Alcohol blended fuels (called gasohol or using ethanol or methanol) can at- tract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. To avoid engine problems, the fuel system should be emptied before storage of 30 days or longer. Drain the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel next season. See Storage Instructions for additional information. Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

CHOKE CONTROL

THROTTLE PRIMER ENGINE OIL

 

FILL CAP /

 

DIPSTICK

SAFETY

IGNITION

KEY

 

GASOLINE

 

FILLER CAP

 

FUEL SHUT-

 

OFF VALVE

RECOIL

STARTER BUTTON

STARTER

 

HANDLE

POWER CORD PLUG

NOTE: ALL ITEMS ARE SHOWN IN THEIR TYPICAL LOCATION. ACTUAL LOCATION MAY VARY WITH ENGINE ON YOUR UNIT.

FIG. 17

TO START ENGINE

•Be sure fuel shut-off valve is in the OPEN position.

Your snow thrower engine is equipped with both a 120 Volt A.C. electric starter and a recoil starter. The electric starter is equipped with a three-wire power cord and plug and is designed to operate on 120 Volt A.C. household current.

•Be sure your house is a 120 Volt A.C. three-wire grounded system. If you are uncertain, consult a licensed electrician.

WARNING: Do not use the electric starter if your house is not a 120 Volt A.C. three-wire grounded system. Se- rious personal injury or damage to your snow thrower could result.

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Model Number Snow ThrowerTraining PreparationOperation Static Electricity HazardMaintenance and Storage API-SF-SJService and Adjustments Parts Packed Separately in Carton14-15 16-18Assembly / PRE-OPERATION HOW to SET UP Your Snow ThrowerRemove Snow Thrower from Carton Unfold Upper HandleInstall Traction Drive Control ROD See Figs Install Auger Control ROD See FigsInstall Discharge Chute / Chute Rotater Head See Fig Check Tire PressureOperation Know Your Snow ThrowerMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting the engineHOW to USE Your Snow Thrower StoppingTo Throw Snow See Fig To Move Forward and Backward See FigBefore Starting the Engine Scraper BARTo Start Engine Snow Throwing Tips Before StoppingIf Recoil Starter has Frozen Maintenance General RecommendationsBefore Each USE LubricationCleaning EngineService and Adjustments To Adjust Snow Thrower HeightChute Deflector Shear Bolts See FigTo Replace Belts See Fig Storage OtherTroubleshooting Limited Warranty

189645 specifications

The Poulan 189645 is an advanced tool designed to meet the demands of both professional and amateur landscapers. Known for its robust build and high performance, this equipment stands out in the crowded market of outdoor power tools.

One of the main features of the Poulan 189645 is its powerful engine. Equipped with a 42 cc 2-cycle engine, it delivers ample power for tackling tough lawn care tasks such as trimming, edging, and optimal cutting performance. The engine is designed for efficiency, providing a balance between power and fuel consumption, ensuring users can work longer without constant refueling.

In terms of design, the Poulan 189645 boasts an ergonomic handle that enhances user comfort during operation. The design minimizes vibration, allowing for extended periods of use without causing fatigue. The adjustable throttle control further allows users to tailor the operation speed according to the task at hand, giving them greater control and flexibility.

One of the innovative technologies integrated into the Poulan 189645 is its Easy Start system. This feature allows for a smooth and hassle-free starting process, eliminating the frustration commonly associated with pull-start engines. The system reduces the effort required to start the machine, making it accessible for users of all skill levels.

Additionally, the Poulan 189645 incorporates a dual-line cutting head equipped with a bump feed mechanism, ensuring a continuous supply of cutting line. This feature enhances productivity by allowing users to get back to work quickly without frequent interruptions for line replacements.

The lightweight construction contributes to the overall usability of the Poulan 189645. At just a fraction of the weight of other models in its class, it minimizes user strain while providing a robust cutting capacity. This combination of lightweight design and powerful performance makes it an ideal choice for anyone looking to maintain their lawn efficiently.

Safety features, including the protective guard and safety switch, are also key characteristics of the Poulan 189645, ensuring that users can operate the tool with confidence.

In summary, the Poulan 189645 is a standout choice for landscapers seeking a blend of power, comfort, and advanced technology. Its high-performance engine, ergonomic design, and user-friendly features make it an invaluable tool for any outdoor maintenance project.
Top Page Image Contents