Troy-Bilt 769-02528 warranty Drive Belt, Lift the brake bracket assembly out of the pulley groove

Page 18

6

Maintaining

Your Snow

Thrower

WARNING

Always stop engine, disconnect spark plug, and ground against engine before cleaning, lubricating or doing any kind of maintenance on your machine.

Figure 28

9.Place a block of wood underneath the auger housing as shown in Figure 29 and separate auger housing from the frame by tilting the housing forward and pulling up the handles.

10.a. Using a 1/2” wrench, remove the hex screw and cupped washer from the center of the pulley on the auger housing. See Figure 30.

b.Lift the brake bracket assembly out of the pulley groove

c.Remove the pulley. Be careful not to lose the key.

11.Remove and replace auger belt inside belt keepers.

12.Apply Loctite 262 to the threads of the hex screw used for mounting the auger pulley.

13.Reassemble pulley to auger housing with hex screw and cupped washer (cupped side toward the pulley). Torque hex screw 150-250 in. lbs.

NOTE: Make sure key is in place on shaft and brake puck is seated in the pulley groove.

If also replacing the drive belt, proceed to the “Drive Belt” instruction. If not, reassemble by performing the previous steps in the opposite order and manner of removal.

Proper Adjustment: With the auger clutch lever in the disengaged position, the top surface of the new belt should be even with the outside diameter of the pulley.

1.To adjust, disconnect ferrule from brake bracket as- sembly and thread ferrule in (towards idler) to increase tension on belt, and out to decrease tension.

NOTE: The brake puck must always be firmly seated in the pulley groove when auger control is disengaged.

Drive Belt

1.Pull the idler pulley away from the backside of the drive belt to relieve the tension and slide the drive belt off the idler pulley. See Figure 31.

2.Remove the belt from the bottom drive pulley and the engine pulley.

Figure 29

B

Key

C

A

 

Figure 30

1

3

2

Figure 31

3.Install the new belt on the pulleys in the reverse order and re-tension with the idler pulley.

Reassemble your unit by performing the previous steps in the opposite order.

18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents OPERATOR’S Manual Two-Stage Snow ThrowerTable of Contents Customer SupportChute Clean-out Tool Your Responsibility Restrict the useSafe Operation Practices TrainingPreparationYour Responsibility Do not modify engineSetting Up Your Snow Thrower Attaching the Chute Assembly Attaching the Shift RodClean-Out Tool Final AdjustmentsDrift Cutters If Equipped Auger Skid ShoesTire Pressure Pneumatic Tires Auger ControlOperating Your Snow Thrower Know Your Snow ThrowerTwo-Way Chute Control Chute Clean-Out ToolDrive Control / Auger Control Lock Ignition KeyStarting The Engine Recoil StarterStopping The Engine Electric Starter on certain modelsTo Engage Augers Always observe safety rules when performing any maintenanceTo Engage Drive Operating TipsShift Rod AdjustmentsMaking Drive ControlSee Figure Adjust skid shoes as follows Chute AssemblyChute Bracket Adjustment Auger ControlMaintaining Your Snow Thrower LubricationReplacing Belts Auger BeltLift the brake bracket assembly out of the pulley groove Drive BeltChanging Friction Wheel Rubber Friction WheelOff-Season Storage Wipe equipment with an oiled rag to prevent rustTrouble Shooting Problem Cause RemedyWarranty TWO Year Supreme WarrantyFor parts and/or accessories refer to customer support on

769-02528 specifications

The Troy-Bilt 769-02528 is a powerful and versatile tool designed to make outdoor work easier and more efficient. This machine is particularly known for its robust performance in various landscaping tasks, including tilling, planting, and cultivating. With a well-engineered design, it addresses the needs of both amateur gardeners and professional landscapers who require reliable equipment.

One of the standout features of the Troy-Bilt 769-02528 is its potent 208cc engine. This engine provides ample power to tackle tough soil conditions and heavy-duty gardening tasks. The engine is designed for easy starting, which is a significant advantage for users who may not want to deal with the frustrations of traditional pull-start systems. The machine is equipped with a recoil starter that engages smoothly, reducing overall strain during the starting process.

In terms of tilling capabilities, the Troy-Bilt 769-02528 is built with a set of 12-inch hardened steel tines. These tines are engineered for durability and efficiency, allowing the tiller to penetrate deeper into the soil and break up compacted ground easily. The adjustable tilling width offers versatility, enabling users to select the appropriate width for their specific gardening needs. The tilling width can vary from 16 to 21 inches, catering to a range of tasks from small garden beds to larger areas.

An intuitive design is evident in the balance and maneuverability of the Troy-Bilt 769-02528. It comes with a low-profile design, which enhances stability during operation. The adjustable handlebars offer comfort and control as users navigate through their gardens. Additionally, the forward and reverse drive options make it easy to maneuver the tiller in tight spaces and improve overall usability.

Another key technology featured in the Troy-Bilt 769-02528 is its self-propelled feature. This allows the tiller to move on its own, reducing the physical effort required by the operator. The combination of this self-propulsion with variable-speed options makes it suitable for various terrains and soil types, ultimately enhancing productivity.

Overall, the Troy-Bilt 769-02528 combines power, efficiency, and innovative technology to deliver a reliable gardening tool. Its features cater to a wide audience, from seasoned gardeners looking for a dependable helper to those just starting in landscaping. With its solid construction and advanced capabilities, the Troy-Bilt 769-02528 stands out as an essential asset for any outdoor project.
Top Page Image Contents