Yard-Man 31AE993I401 Shift Lever, Chute Crank, Chute Tilt Control, Discharge Chute, Skid Shoe

Page 8
Shift Lever

Shift Lever

The shift lever is located in the center of the handle panel and is used to determine ground speed and direction of travel. It can be moved into any of eight positions. See Figure 9.

IMPORTANT: Always release traction the control before changing speeds.

Forward

Your snow thrower has six forward (F) speeds. Position number one (1) is the slowest and position number six

(6)is the fastest.

Reverse

Your snow thrower has two reverse (R) speeds. R1 is the slower, while R2 is the faster of the two.

Chute Crank

The chute crank is located on the left hand side of the snow thrower. To change the direction in which snow is thrown, turn the chute crank as follows:

Turn clockwise to discharge to the left;

Turn counterclockwise to discharge to the right.

Operate the snow thrower in open areas until becoming familiar with these controls.

Chute Tilt Control

The distance snow is thrown can be changed by adjusting the angle of the chute assembly. Move the chute tilt control forward to decrease the distance, toward the rear to increase. See Figure 9.

Discharge Chute

The angle of the discharge chute controls the distance that the snow is thrown. Tilt the discharge chute up for greater distance; tilt down for less distance.

Skid Shoe

The position of the skid shoe is determined by the condition of the ground from where snow has to be removed.

Headlight

The headlight is on whenever the engine is running.

Wheel Steering Controls

The left and right wheel steering controls are located on the underside of the handles and are used to assist in steering the snow thrower.

Squeeze the right wheel steering control when turning right; squeeze the left control when turning left.

Throttle Control

The throttle control is located on the engine. It regulates the speed of the engine. See Figure 9.

Safety Ignition Key

The safety ignition key must be fully inserted in the switch before the unit will start. Remove key when snow thrower is not in use. Do not attempt to turn the key. See Figure 9.

Traction Control /

 

 

 

Auger Control Lock

Shift Lever

 

 

 

Headlight

 

 

 

 

 

Auger Drive Control

 

Fuel Tank

 

Chute Tilt

 

 

 

 

Discharge

 

Control

 

Chute

 

 

 

 

 

Chute Crank

 

 

Wheel Steering

 

 

Control

 

Electric

 

 

Primer

Starter

 

 

Button

 

 

 

 

 

Choke

Switch

 

 

Box

 

 

 

Auger

 

Safety

Recoil

 

Ignition Key

Starter

 

Skid Shoe

Throttle

Handle

 

 

 

 

Control

 

Figure 9

8

Image 8
Contents Model 31AE993I401 OPERATOR’S MANUAL33” Snow Thrower MTD PRODUCTS INC. P.O. BOX 368022 CLEVELAND, OHIOTABLE OF CONTENTS ContentFINDING MODEL NUMBER CALLING CUSTOMER SUPPORTSECTION 1 IMPORTANT SAFE OPERATION PRACTICES TrainingPreparation OperationMaintenance And Storage SECTION 2: ASSEMBLING YOUR SNOW THROWER UnpackingLoose Parts Assembling HandleAuger Control Final AdjustmentsTraction Control and Shift Lever SECTION 3: KNOWING YOUR SNOW THROWER Auger ControlTraction Control / Auger Control Lock Skid ShoesSafety Ignition Key Shift LeverChute Crank Chute Tilt ControlSECTION 4: OPERATING YOUR SNOW THROWER Before StartingGas And Oil Fill-up To Start EngineSECTION 5: MAKING ADJUSTMENTS To Stop EngineTo Engage Wheel Drive To Engage AugersSkid Shoe Adjustment Auger Control AdjustmentChute Assembly Drive WheelsSECTION 6: MAINTAINING YOUR SNOW THROWER General RecommendationsCarburetor LubricationSECTION 7: SERVICING YOUR SNOW THROWER AugersShave Plate and Skid Shoes Auger Bearings and ShaftReplacing Belts Auger BeltChanging Friction Wheel Rubber Drive BeltEngine SECTION 8: OFF-SEASONSTORAGESECTION 9: TROUBLESHOOTING ProblemCause RemedyModel 31AE993I401 Part No Part DescriptionModel 31AE993I401 Model 31AE993I401 A 32 Model 31AE993I401 15 22 18 14 7 21 1 13 3 20 20 24 31 Notes Page MANUFACTURER’S LIMITED WARRANTY FOR