Husqvarna 5524SEB owner manual Repair Parts Auger Housing / Impeller Assembly

Page 21

REPAIR PARTS

AUGER HOUSING / IMPELLER ASSEMBLY

SNOW THROWER - MODEL NO. 5224SEB (96193001000), PRODUCT NO. 961 93 00-10

KEY PART

 

NO. NO.

DESCRIPTION

4532 19 10-79 Pulley, Impeller

5532 18 89-09 Bearing Assembly, Flange

6532 15 53-77 Nut, Hex Flange 5/16-18

7

532 18 03-55

Bolt, Flat Head, Carriage 5/16-18 x 5/8

8

872 27 05-05

Bolt, Carriage 5/16-1 8 x 5/8

9532 17 88-20 Nut, Cage 3/8-16

10532 18 40-90 Housing, Auger

11532 18 40-96 Bar, Scraper

12532 18 40-95 Bracket, Corner Discharge

13532 17 53-22 Base, Discharge Chute

14

819 11 15-07

Washer, Flat

15

810 04 05-00

Washer, Lock 5/16

16

874 95 05-12

Screw, Hex Head 5/16-18 x 3/4

18532 17 95-82 Screw, Hex Head 5/16 x 1

19873 80 04-00 Nut, Hex Lock 1/4-20

20873 80 05-00 Nut, Hex Lock 5/16-18

21532 15 54-15 Washer, Flat 5/16

22532 18 40-94 Skid Plate, RH

23532 17 92-46 Washer, Nylon, Friction

24

872 27 05-06

Bolt, Carriage

5/16-18 x 3/4

25

532 18 56-00

Bolt, Shoulder

1/4-20

26

532 17 46-58

Bearing, Auger

 

27532 17 46-97 Washer, Thrust, 1"

28532 19 20-90 Bolt, Shear

29532 18 40-93 Skid Plate, LH

30532 19 94-74 Auger Assembly, RH

31532 19 94-73 Auger Assembly, LH

32532 17 46-99 O-Ring

33532 17 47-00 Bushing, Flange 3/4

34532 17 46-81 Washer, Thrust 3/4

35532 17 46-84 Bearing, Thrust 3/4

36532 17 46-60 Shaft, Impeller

37532 17 46-83 Washer, Thrust 5/8

38532 17 46-86 Bushing, Flange 5/8

39 532 15 00-78 Screw, Hex Head 5/16-18 x 3/4

40532 08 64-47 Plug, Case

41532 17 46-88 Housing, Gearbox, RH

42532 17 46-98 Seal, Oil

43532 17 47-01 Bushing, Flange, 1"

44

532 18 92-82

Key, Square 1/4 x 1/4 x 7/8

45

532 17 46-59

Gear, Worm

46

532 17 46-57

Shaft, Auger

47532 17 46-87 Housing, Gearbox, LH

48532 18 41-05 Impeller Assembly

49

874 78 04-26

Screw, Hex Head 1/4-20 x 1-5/8

50

532 17 53-11

Gasket, Gearbox

51

532 18 42-05

Pin, Roll 3/16 x 1-1/8

54532 05 38-47 Washer, Flat 1/4

55532 18 82-43 Kit, Shear (Contains 6 each of Key Numbers 19 and 28)

56532 18 06-84 Multi-Wrench

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your lawn mower and void your warranty.

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents 5524SEB Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Assembly / PRE-OPERATION HOW to SET UP Your Snow ThrowerRemove Snow Thrower from Carton Install Speed Control ROD See Figs Install Traction Drive Control ROD See FigsUnfold Upper Handle Install Auger Control ROD See Figs Install Discharge Chute / Chute Rotater Head See FigCheck Tire Pressure Know Your Snow Thrower OperationRecoil auxiliary starter handle used for starting the engine Meets A.N.S.I. Safety RequirementsStopping HOW to USE Your Snow ThrowerUsing the CLEAN-OUT Tool See Fig To Throw Snow See FigTo Move Forward and Backward See Fig Before Starting the Engine Scraper BARTo Start Engine Snow Throwing Tips Before StoppingIf Recoil Starter has Frozen General Recommendations MaintenanceBefore Each USE LubricationEngine CleaningTo Adjust Snow Thrower Height Service and AdjustmentsChute Deflector Shear Bolts See FigTo Replace Belts See Fig Other StorageTroubleshooting Service Notes Repair Parts Repair Parts Auger Housing / Impeller Assembly Control Panel / Discharge Chute KEY Part Description Handles Repair Parts Drive Repair Parts Repair Parts Chassis / Engine / Pulleys KEY Part Description Chassis / Engine / PulleysRepair Parts Wheels / Decals Wheels / Decals Ionsmitat ILD NA SON Iept EXC4 Onict SE Statementwarranty
Top Page Image Contents