Husqvarna 524STE owner manual Storage, Other

Page 18

TO REMOVE WHEELS (See Fig. 22)

•Remove the klik pin and remove wheel from axle.

IMPORTANT: When installing wheel, be sure to use the in- nermost hole in axle and the wheel hub hole. To disengage drive system from the wheels (for pushing or transporting the snow thrower), remove klik pin from wheel hub and insert pin into the outermost hole in axle only.

KLIK PIN

OUTER HOLE

 

INNER

 

HOLE

WHEEL

WHEEL HUB

FIG. 22

NOTE: To seal punctures or prevent fl at tires due to slow leaks, tire sealant may be purchased from your local parts dealer.Tire sealant also prevents tire dry rot and corrosion.

ENGINE

See engine manual.

CARBURETOR

Your carburetor is not adjustable. Engine performance should not be affected at altitudes up to 7,000 feet (2,134 meters). If your engine does not operate properly due to suspected carburetor problems, take your snow thrower to a qualified service center.

ENGINE SPEED

Never tamper with the engine governor, which is factory set for proper engine speed. Overspeeding the engine above the factory high speed setting can be dangerous and will void the warranty. If you think the engine-governed high speed needs adjusting, contact a qualifi ed service center, which has proper equipment and experience to make any necessary adjustments.

STORAGE

Immediately prepare your snow thrower for storage at the end of the season or if the unit will not be used for 30 days or more.

WARNING: Never store the snow thrower with gasoline in the tank inside a building where fumes may reach an open flame, spark or pilot light as on a furnace, water heater, clothes dryer or gas appliance. Allow the engine to cool before storing in any enclosure.

SNOW THROWER

When snow thrower is to be stored for a period of time, clean it thoroughly, remove all dirt, grease, leaves, etc. Store in a clean, dry area.

1.Clean entire snow thrower (See “CLEANING” in the Maintenance section of this manual).

2.Inspect and replace belts, if necessary (See “TO RE- PLACE BELTS”in the Service and Adjustments section of this manual).

3.Lubricate as shown in the Maintenance section of this manual.

4.Be sure that all nuts, bolts, screws, and pins are securely fastened. Inspect moving parts for damage, breakage and wear. Replace if necessary.

5.Touch up all rusted or chipped paint surfaces; sand lightly before painting.

ENGINE

See engine manual.

FUEL SYSTEM

 

IMPORTANT: It is important to prevent gum deposits from

 

forming in essential fuel system parts such as carburetor,

 

fuel hose, or tank during storage.Also, alcohol blended fuels

 

(called gasohol or using ethanol or methanol) can attract

 

moisture which leads to separation and formation of acids

 

during storage. Acidic gas can damage the fuel system of

 

an engine while in storage.

18

 

•Empty the fuel tank by starting the engine and letting it run until the fuel lines and carburetor are empty.

•Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

•Use fresh fuel next season.

NOTE: Fuel stabilizer is an acceptable alternative in min- imizing the formation of fuel gum deposits during storage. Add stabilizer to gasoline in fuel tank or storage container. Always follow the mix ratio found on stabilizer container. Run engine at least 10 minutes after adding stabilizer to allow the stabilizer to reach the carburetor. Do not empty the gas tank and carburetor if using fuel stabilizer.

ENGINE OIL

Drain oil (with engine warm) and replace with clean en- gine oil. (See “ENGINE” in the Maintenance section of this manual).

CYLINDER

1.Remove spark plug.

2.Pour one ounce (29 ml) of oil through spark plug hole into cylinder.

3.Pull recoil starter handle slowly a few times to distribute oil.

4.Replace with new spark plug.

OTHER

•Do not store gasoline from one season to another.

•Replace your gasoline can if your can starts to rust. Rust and/or dirt in your gasoline will cause problems.

•If possible, store your snow thrower indoors and cover it to protect it from dust and dirt.

•Cover your snow thrower with a suitable protective cover that does not retain moisture.Do not use plastic.Plastic cannot breathe, which allows condensation to form and will cause your snow thrower to rust.

IMPORTANT: Never cover snow thrower while engine/ exhaust area is still warm.

Page 17 Page 19
Image 18
Page 17 Page 19
Contents 524STE Operation TrainingPreparation Static Electricity HazardMaintenance and Storage API SG-SL14-15 Service and AdjustmentsParts Packed Separately in Carton 16-18Remove Snow Thrower from Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Unfold Upper HandleInstall Traction Drive Control ROD See Figs Install Auger Control ROD See FigsInstall Discharge Chute / Chute Rotater Head See Fig Check Tire PressureOperation Know Your Snow ThrowerMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting the engineHOW to USE Your Snow Thrower StoppingTo Move Forward and Backward See Fig When traction drive control lever is engagedUsing the CLEAN-OUT Tool See Fig To Throw Snow See FigBefore Starting the Engine Scraper BARTo Start Engine Snow Throwing Tips Before StoppingIf Recoil Starter has Frozen Before Each USE MaintenanceGeneral Recommendations LubricationCleaning EngineChute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height Shear Bolts See FigTo Replace Belts See Fig Storage OtherTroubleshooting Repair Parts KEY Part Description Control Panel / Discharge Chute Repair Parts Repair Parts Handles Handles Drive Repair Parts Chassis / Engine / Pulleys KEY Part Description Wheels / Decals 532 18 78-31 Wheel Assembly, 13, LH Rantywar Tementsta Sion Tmita ILD NA SON ITP Eexc 4ON ITC ES

524STE specifications

The Husqvarna 524STE is a powerful and versatile snow thrower designed for homeowners who seek efficiency and performance in winter conditions. This piece of equipment is engineered to handle various types of snow, making it ideal for both light snowfalls and heavy snow accumulations. With its robust design and innovative features, the 524STE provides exceptional reliability and ease of use.

One of the standout features of the Husqvarna 524STE is its 24-inch clearing width. This allows the machine to clear large areas quickly, reducing the time spent on snow removal. The powerful engine, typically a 208cc 4-stroke, ensures that the snow thrower can handle dense snow even in harsh winter conditions. The 524STE also incorporates an easy-start mechanism, allowing for quick ignition even in cold weather, which is a significant advantage for early morning snow clearing.

The innovative two-stage snow thrower design is another key characteristic of the 524STE. This mechanism uses an auger to collect the snow before an impeller throws it away, which effectively reduces the likelihood of clogging and enhances performance. The adjustable chute allows operators to direct the snow precisely where they want it, providing better control and efficiency during operation.

Husqvarna has also equipped the 524STE with convenient features such as ergonomic controls and adjustable handle heights, which allow for comfortable operation for users of various sizes. The units are designed with durability in mind, featuring heavy-duty materials that can withstand harsh winter conditions. The snow thrower also comes with durable tires that enhance traction and maneuverability, enabling it to navigate various terrains effortlessly.

For added safety, the Husqvarna 524STE includes features such as a safety switch that ensures the machine only operates when the operator is in control. Easy maintenance options also allow for extended use, as owners can quickly service the machine as needed.

With its impressive range of features, advanced technologies, and user-friendly design, the Husqvarna 524STE is an excellent investment for anyone looking to tackle winter weather with confidence and efficiency. Whether managing the driveway or clearing pathways, this snow thrower proves to be a reliable partner in any snow-clearing task.
Top Page Image Contents