Husqvarna 8527 STE owner manual Maintenance and Storage, Api-Sf-Sj

Page 3

Do not put hands or feet near or under rotating parts. Keep clear of the discharge opening and front auger area at all times.

Exercise extreme caution when operating on or cross- ing gravel drives, walks or roads. Stay alert for hidden hazards or traffic.

After striking a foreign object, stop the engine (motor), remove wire from the spark plug, thoroughly inspect snow thrower for any damage, and repair the damage before restarting and operating the snow thrower.

If the unit should start to vibrate abnormally, stop the engine (motor) and check immediately for the cause. Vibration is generally a warning of trouble.

Stop the engine (motor) whenever you leave the oper- ating position, before unclogging the auger/impeller housing or discharge chute and when making any repairs, adjustments, or inspections.

When cleaning, repairing, or inspecting, make certain all controls are disengaged and the auger/impeller and all moving parts have stopped. Disconnect the spark plug wire and keep the wire away from the spark plug to prevent accidental starting.

Take all possible precautions when leaving the snow thrower unattended.Disengage the auger/impeller, stop engine (motor), and remove key.

Do not run the engine (motor) indoors, except when starting the engine (motor) and for transporting the snow thrower in or out of the building. Open the outside doors.

WARNING: Exhaust fumes are dan- gerous (containing CARBON MONOX- IDE, an ODORLESS and DEADLY GAS).

Do not clear snow across the face of slopes. Exercise extreme caution when changing direction on slopes. Do not attempt to clear steep slopes.

Never operate the snow thrower without proper guards, plates or other safety protective devices in place.

Never operate the snow thrower near glass enclo- sures, automobiles, window wells, drop–offs, and the like without proper adjustment of the snow discharge angle. Keep children and pets away.

Do not overload the machine capacity by attempting to clear snow at too fast a rate.

Never operate the machine at high transport speeds on slippery surfaces. Look behind and use care when backing up.

Never direct discharge at bystanders or allow anyone in front of the unit.

Disengage power to the auger/impeller when snow thrower is transported or not in use.

Use only attachments and accessories approved by the manufacturer of the snow thrower (such as wheel weights, counterweights, cabs, tire chains, electric start kits, etc.).

Never operate the snow thrower without good visibility or light. Always be sure of your footing and keep a fi rm hold on the handles. Walk; never run.

Do not overreach. Keep proper footing and balance at all times.

This snow thrower is for use on sidewalks, driveways and other ground level surfaces.

Do not use the snow thrower on surfaces above ground level such as roofs of residences, garages, porches or other such structures or buildings.

MAINTENANCE AND STORAGE

Check shear bolts and other bolts at frequent intervals for proper tightness to be sure the equipment is in safe working condition.

Never store the snow thrower with fuel in the tank inside a building where ignition sources are present such as hot water and space heaters, clothes dryers, and the like. Allow the engine (motor) to cool before storing in any enclosure.

Always refer to operator’s guide instructions for im- portant details if the snow thrower is to be stored for an extended period.

Maintain or replace safety and instruction labels, as necessary.

Run the snow thrower, with auger engaged, a few minutes after throwing snow to clear the machine and prevent freeze-up of the auger/impeller.

CONGRATULATIONS on your purchase of a new snow thrower. It has been designed, engineered and manufactured to give best possible dependability and performance.

Should you experience any problem you cannot easily remedy, please contact your nearest authorized service center/department. We have competent, well-trained tech- nicians and the proper tools to service or repair this unit.

Please read and retain this manual. The instructions will enable you to assemble and maintain your snow thrower properly. Always observe the “SAFETY RULES”.

SERIAL NUMBER: ___________________________

DATE OF PURCHASE: _______________________

THE MODEL AND SERIAL NUMBERSWILL BE FOUND ON A DECAL ATTACHEDTOTHE REAR OFTHE SNOW THROWER HOUSING.

YOU SHOULD RECORD BOTH SERIAL NUMBER AND DATE OF PURCHASE AND KEEP IN A SAFE PLACE

FOR FUTURE REFERENCE.

3

PRODUCT SPECIFICATIONS

Gasoline Capacity

4.0 Quarts

and Type:

Unleaded Regular only

 

 

Oil Type

SAE 30 (above 40°F)

(API-SF-SJ):

SAE 5W-30 or 10W-30 (0° to +40°F)

 

SAE 0W-30 (below 0°F)

 

 

Oil Capacity:

26 Ounces

 

 

Spark Plug:

Champion RN4C (Gap: .030")

 

 

CUSTOMER RESPONSIBILITIES

Read and observe the safety rules.

Follow a regular schedule in maintaining, caring for and using your snow thrower.

Follow the instructions under “Maintenance” and “Stor- age” sections of this owner’s manual.

Image 3
Contents 8527STE Static Electricity Hazard TrainingPreparation OperationAPI-SF-SJ Maintenance and Storage16-18 Service and AdjustmentsParts Packed Separately in Carton 14-15Unfold Upper Handle Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Remove Snow Thrower from CartonInstall Auger Control ROD See Figs Install Traction Drive Control ROD See FigsCheck Tire Pressure Install Discharge Chute / Chute Rotater Head See FigKnow Your Snow Thrower OperationRecoil auxiliary starter handle used for starting the engine Meets A.N.S.I. Safety RequirementsStopping HOW to USE Your Snow ThrowerTo Move Forward and Backward See Fig To Throw Snow See FigBefore Starting the Engine Scraper BARTo Start Engine Snow Throwing Tips Before StoppingIf Recoil Starter has Frozen Lubrication MaintenanceGeneral Recommendations Before Each USEEngine CleaningShear Bolts See Fig Service and AdjustmentsTo Adjust Snow Thrower Height Chute DeflectorTo Replace Belts See Fig Other StorageTroubleshooting Repair Parts 532 18 532 05 Washer, FlatControl Panel / Discharge Chute 532 15 Repair Parts Handles Handles Drive Repair Parts Chassis / Engine / Pulleys Screw, Hex Washer Head 5/16-18 x 3/4 Wheels / Decals 532 18 78-33 Wheel Assembly, 16, LH Sion Tmita ILD NA SON ITP Eexc 4ON ITC ES Rantywar Tementsta