Husqvarna 8527SBE owner manual KEY Part Description

Page 29

REPAIR PARTS

CHASSIS / ENGINE / PULLEYS

SNOW THROWER - MODEL NO. 8527SBE (96193000300), PRODUCT NO. 961 93 00-03

KEY	PART		KEY	PART
NO.	NO.	DESCRIPTION	NO.	NO.	DESCRIPTION
1	532 18 10-44 Spring, Traction Idler		29	532 19 22-13	Belt Cover Assembly
2	532 18 05-22 Pulley, Idler (2-1/4)				(Includes Toolbox Cover)
3	- - -	Engine, Tecumseh, Model Number	30	532 17 88-30	Cover, Toolbox
		LH185A (For engine service and	31	817 49 04-08	Screw, Hex Head 1/4-20 x 1/2
		replacement parts, call Tecumseh	32	532 17 92-56	Bolt, Shoulder 5/16-18
		Products at 1-800-558-5402)	33	532 18 78-53	Bellcrank Shifter
4	874 78 05-20	Screw, Hex Head 5/16-18 x 1-1/4	34	532 18 04-01	Screw, Hex Head 1/4-28 x 3/4
6	532 05 92-89	Washer, Flat	35	532 19 57-67 Arm, Auger Control
7	873 93 05-00	Nut, Jam, Lock 5/16-18	36	873 80 05-00	Nut, Lock 5/16-18
8	532 17 53-30	Pin, Idler Pivot	37	532 18 40-86	Bellcrank
9	532 17 90-92 V-Belt, Traction Drive		38	532 18 71-01	Link, Speed Control
10	810 04 05-00	Washer, Lock 5/16	39	532 19 21-10	Trunnion, Pivot Bracket
11	817 49 05-08	Screw, Hex Head 5/16-18 x 1/2	40	532 17 88-20	Nut, Cage 3/8-16
12	532 17 92-59 Impeller Idler Arm Assembly		41	532 70 02-79	Hairpin, Cotter 3/32 x 1/2
13	532 08 51-79 Retainer, Hairpin		42	532 17 90-65	Pin, Pivot Bracket
14	532 17 88-28	Spring, Brake	43	532 18 40-85	Bracket, Bellcrank
15	532 18 35-33 V-Belt, Impeller Drive		44	871 21 06-16	Screw, Hex Head
16	532 19 23-06	Screw, Hex Head 3/8-16 x 1-1/4	45	532 18 40-74	Pivot Bracket, Impeller Idler Arm
17	532 18 48-04	Arm, Idler	46	532 18 40-84	Pan, Frame Bottom
18	874 78 05-24	Screw, Hex Head 5/16-18 x 1-1/2	47	871 02 05-12	Screw, Hex Head 5/16-18 x 3/4
19	532 17 53-31 Bushing, Idler Pivot		48	532 18 11-56	Nut, Speed 5/16-18
20	532 18 05-23 Pulley, Idler (2-3/4)		49	532 18 40-73	Frame Assembly
21	874 61 05-16	Screw, Hex Head 5/16-18 x 1	50	532 18 80-02	Plate, Frame End
22	532 17 93-71 Spacer, Engine Pulley		51	532 19 95-14	Shaft, Auger Control
23	532 18 04-78 Pulley, Engine, Traction Drive		52	532 05 70-79	Washer, Hardened
24	532 17 91-57 Pulley, Engine, Impeller Drive		53	532 19 22-75	Roller
25	532 06 27-35	Washer, Flat 3/8	54	532 19 21-47	Ring, Crescent
26	532 85 02-63	Washer, Lock, Helical 3/8	55	812 00 00-02	E-Ring
27	532 85 10-84	Screw, Hex Head 3/8-24 x 1-3/8	57	811 05 05-00	Washer, Lock, External Tooth 5/16
28	532 15 54-52	Guide, Belt	58	532 18 38-54	Power Cord

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your lawn mower and void your warranty.

29

Image 29

Contents 8527SBE Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton HOW to SET UP Your Snow Thrower Assembly / PRE-OPERATIONRemove Snow Thrower from Carton Unfold Upper HandleInstall Auger Control ROD See Figs Install Traction Drive Control ROD See FigsCheck Tire Pressure Install Discharge Chute / Chute Rotater Head See FigInstall Chute Deflector Remote Control See Figs Know Your Snow Thrower OperationPrimer Ignition KEYDrive speed control lever used to select forward or Meets A.N.S.I. Safety RequirementsStopping HOW to USE Your Snow ThrowerTo Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigTo Throw Snow See Fig To Start Engine Before Starting the EngineScraper BAR If Recoil Starter has Frozen Snow Throwing TipsBefore Stopping General Recommendations MaintenanceBefore Each USE LubricationEngine CleaningTo Adjust Snow Thrower Height Service and AdjustmentsChute Deflector Shear Bolts See FigTo Replace Belts See Fig Other StorageTroubleshooting Repair Parts Auger Housing / Impeller Assembly Repair Parts Control Panel / Discharge Chute KEY Part Description Handles 532 18 41-10 Lever, Auger Control, RH Drive Repair Parts Chassis / Engine / Pulleys KEY Part Description Wheels / Decals 532 40 Sion Tmita ILD NA SON ITP Eexc 4ON ITC ES Rantywar Tementsta