McCulloch 96192004101 Impeller Belt, Traction Belt, Idler ARM Bracket, Idler Pulley, Belt Guide

Page 34

REPAIR PARTS SNOW THROWER - - MODEL NUMBER MC627ES (96192004101)

CHASSIS / ENGINE / PULLEYS

23		22	14
24			14	21
24				21
				20
11
14	21		20	19
13			20	18
13				18
12				17
12	14			16
		15		16
		15		6
				6
	7
10
				5
8				4
8				3
				3
				9

1

2

01.21.003-C

KEY	PART	DESCRIPTION	KEY	PART	DESCRIPTION
NO.	NO.	DESCRIPTION	NO.	NO.	DESCRIPTION

1	408007	IMPELLER BELT
2	419744	TRACTION BELT
3	423723X431	IDLER ARM BRACKET
4	180523	IDLER PULLEY
5	426589	NUT 5/16-18

674780524 SCREW 5/16-18 X 1 .50

7423990X431 IDLER BRACKET

8

428867

SCREW 5/16-18 X .625

9424297 SHOULDER BOLT 5/16-18 X .500

10751153 NUT 5/16-18 NYLOCK

11187786 TRACTION IDLER ARM

12180522 TRACTION PULLEY

13	74780520	SCREW 5/16-18 X 1 .00
14	59289	WASHER
15	73800500	NUT 5/16-18
16	851084	SCREW 3/8-24 X 1.375
17	400026	WASHER

18426491 PULLEY ENG IMPELLER

19426490 PULLEY ENG TRACTION

2074610516 SCREW 5/16-18 X 1 .00

2110040500 LOCKWASHER 5/16

22

155452

BELT GUIDE

2311050500 LOCKWASHER 5/16

24175331 IDLER BUSHING

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty.

34

Image 34

Contents MC627ES Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Remove Snow Thrower from CartonInstall Traction Drive Control ROD See Figs Install Speed Control ROD See FigsUnfold Upper Handle Install Discharge Chute / Chute Rotater Head See Fig Install Auger Control ROD See FigsCheck Tire Pressure Primer OperationKnow Your Snow Thrower Ignition KEYMeets A.N.S.I. Safety Requirements Electric start button used for starting the engineTo USE Fuel SHUT-OFF Valve See Fig HOW to USE Your Snow ThrowerStopping To USE Choke Control See FigTo Throw Snow See Fig Using the CLEAN-OUT Tool See FigTo Move Forward and Backward See Fig Scraper BAR See Fig To Adjust Skid Plates See FigBefore Starting the Engine Check Engine OIL Level See FigBefore Stopping Snow Throwing TipsTo Start Engine If Recoil Starter has FrozenBefore Each USE MaintenanceGeneral Recommendations LubricationCleaning EngineChute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height Shear Bolts See FigTo Replace Belts See Fig Carburetor To Adjust Cable Tension See FigTo Remove Wheels See Fig Engine SpeedFuel System StorageOther Engine OILTroubleshooting Exploded KEY Part Description Auger 27 LH Auger HousingScraper BAR Auger 27 RHSkid Plate LH Auger BearingBearing Plug Skid Plate RHDeflector Seal Chute WeldmentDeflector Weldment StrapCable Assembly Heat Shield LEVER/CABLE Rotator AssemblyCable Assembly Adjustable Rotator HeadLower Handle 196944X431 Panel Bracket LH 196943X431 Panel Bracket RHHandle Grip Pivot Support WeldmentKnob RED SpacerRetainer Handle KnobShifter ROD TOP Impeller RODTraction ROD Shifter ROD BottomHeadlight Bezel Wire HarnessConsole Panel Flood HeadlightRepair Parts Snow Thrower - Model Number MC627ES Drive Speed Selector AssemblyDrive Plate Assembly Rubber RingSprocket Axle ShaftRoll PIN 3/16 Clik PIN427963X421 Complete LCT EngineFrame Engine Mounting PlateIdler ARM Bracket Impeller BeltTraction Belt Idler Pulley432331X421 Wheel Assembly LH432332X421 Safety Ignition KEY 422663181037 DECAL, DangerService Notes Service Notes Limited Warranty