McCulloch MC624ES Impeller Belt, Traction Belt, Idler ARM Bracket, Idler Pulley, Belt Guide

Page 36

REPAIR PARTS SNOW THROWER - - MODEL NUMBER MC624ES (96192004000)

CHASSIS / ENGINE / PULLEYS

23		22	14
24			14	21
24				21
				20
11
14	21		20	19
13			20	18
13				18
12				17
12	14			16
		15		16
		15		6
				6
	7
10
				5
8				4
8				3
				3
				9

1

2

01.21.003-C

KEY	PART	DESCRIPTION	KEY	PART	DESCRIPTION
NO.	NO.	DESCRIPTION	NO.	NO.	DESCRIPTION

1	408007	IMPELLER BELT
2	419744	TRACTION BELT
3	423723X431	IDLER ARM BRACKET
4	180523	IDLER PULLEY
5	426589	NUT 5/16-18

674780524 SCREW 5/16-18 X 1 .50

7423990X431 IDLER BRACKET

8

428867

SCREW 5/16-18 X .625

9424297 SHOULDER BOLT 5/16-18 X .500

10751153 NUT 5/16-18 NYLOCK

11187786 TRACTION IDLER ARM

12180522 TRACTION PULLEY

13	74780520	SCREW 5/16-18 X 1 .00
14	59289	WASHER
15	73800500	NUT 5/16-18
16	851084	SCREW 3/8-24 X 1.375
17	400026	WASHER

18426491 PULLEY ENG IMPELLER

19426490 PULLEY ENG TRACTION

2074610516 SCREW 5/16-18 X 1 .00

2110040500 LOCKWASHER 5/16

22

155452

BELT GUIDE

2311050500 LOCKWASHER 5/16

24175331 IDLER BUSHING

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty.

34

Image 36

Contents MC624ES Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Assembly / PRE-OPERATION HOW to SET UP Your Snow ThrowerParts Packed Separately in Carton Remove Snow Thrower from CartonInstall Speed Control ROD See Figs Install Traction Drive Control ROD See FigsUnfold Upper Handle Install Auger Control ROD See Figs Install Discharge Chute / Chute Rotater Head See FigCheck Tire Pressure Operation Know Your Snow ThrowerPrimer Ignition KEYMeets A.N.S.I. Safety Requirements Electric start button used for starting the engineHOW to USE Your Snow Thrower StoppingTo USE Fuel SHUT-OFF Valve See Fig To USE Choke Control See FigUsing the CLEAN-OUT Tool See Fig To Throw Snow See FigTo Move Forward and Backward See Fig To Adjust Skid Plates See Fig Before Starting the EngineScraper BAR See Fig Check Engine OIL Level See FigSnow Throwing Tips To Start EngineBefore Stopping If Recoil Starter has FrozenMaintenance General RecommendationsBefore Each USE LubricationCleaning EngineService and Adjustments To Adjust Snow Thrower HeightChute Deflector Shear Bolts See FigTo Replace Belts See Fig To Adjust Cable Tension See Fig To Remove Wheels See FigCarburetor Engine SpeedStorage OtherFuel System Engine OILTroubleshooting Exploded KEY Part Description Auger Housing Auger Assembly LHAuger Assembly RH Scrapper BARAuger Bearing Bearing PlugSkid Plate LH Skid Plate RHKnob Black POP RivetWasher Plastic WasherLEVER/CABLE Rotator Assembly Cable Assembly AdjustableCable Assembly Heat Shield Rotator Head196944X431 Panel Bracket LH 196943X431 Panel Bracket RH Handle GripLower Handle Pivot Support Weldment424517X431 Control Lever LH 424516X431 Control Lever RH 426918X008 Impeller ROD ARM Interlock BailSpacer RetainerImpeller ROD Traction RODShifter ROD TOP Shifter ROD BottomConsole Panel Interlock SpringInterlock CAM Torsion SpringRepair Parts Snow Thrower - Model Number MC624ES Drive Assembly Drive Plate AssemblySpeed Selector Rubber RingAxle Shaft Roll PIN 3/16Sprocket Clik PINComplete LCT Engine Frame427963X421 Engine Mounting PlateElectric Start Only Part Description Impeller Belt Traction BeltIdler ARM Bracket Idler PulleyWheel Assembly LH 433665X421433666X421 Safety Ignition KEY 422663181037 DECAL, DangerService Notes Service Notes Limited Warranty