McCulloch 96192004001 owner manual To Throw Snow See Fig, Using the CLEAN-OUT Tool See Fig

Page 10

OPERATION

TO THROW SNOW (See Fig. 13)

The auger rotation is controlled by the auger control lever located on the right side handle.

•Squeeze auger control lever to handle to engage the auger and throw snow.

•Release the auger control lever to stop throwing snow.

AUGER

CONTROL

LEVER

FIG. 13

USING THE CLEAN-OUT TOOL (See Fig. 14)

In certain snow conditions, the discharge chute may be- come clogged with ice and snow. Use the clean-out tool to dislodge this blockage.

When cleaning, repairing, or inspecting, make certain all controls are disengaged and the au- ger/impeller and all moving parts have stopped. Disconnect the spark plug wire and keep the wire away from the spark plug to prevent ac- cidental starting.

•Release the auger control lever and shut off the engine.

•Remove the clean-out tool from it's mounting clip. Grasp the tool firmly by the handle and push and twist the tool into the discharge chute to dislodge the blockage.

After the packed snow has been dislodged, return the clean- out tool to it's mounting clip by pushing it into the clip.

•Make sure the discharge chute is pointed in a safe direc- tion (no vehicles, buildings, people, or other objects are in the direction of discharge) before restarting engine.

•Restart the engine, then squeeze the auger control lever to the handle to clear snow from the auger hous- ing and the discharge chute.

DISCHARGE CHUTE

CLEAN-OUT

TOOL

MOUNTING

CLIP

TO MOVE FORWARD AND BACKWARD (See Fig. 15)

SELF-PROPELLING, forward and reverse movement of the snow thrower, is controlled by the traction drive control lever located on the left side handle.

•Squeeze traction drive control lever to handle to engage the drive system.

•Release traction drive control lever to stop the forward or reverse movement of the snow thrower.

SPEED and DIRECTION are controlled by the drive speed control lever.

•Press downward on the speed control lever and move lever to desired position BEFORE engaging the trac- tion drive control lever. Be sure lever springs back and locks into desired position.

CAUTION: Do not move speed control lever when traction drive control lever is engaged. Damage to the snow thrower can result.

•Slower speeds are for heavier snow and faster speeds are for light snow and transporting the snow thrower. It is recommended that you use a slower speed until you are familiar with the operation of the snow thrower.

NOTE: When both traction drive and auger control levers are engaged, the traction drive control lever will lock the auger control lever in the engaged position. This will allow you to release your right hand from the handle and adjust the discharge chute direction without interrupting the snow throwing process.

TRACTION DRIVE

CONTROL LEVER

DRIVE SPEED

CONTROL LEVER

FIG. 16

FIG. 14

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents MC624ES Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Remove Snow Thrower from CartonInstall Traction Drive Control ROD See Figs Install Speed Control ROD See FigsUnfold Upper Handle Install Discharge Chute / Chute Rotater Head See Fig Install Auger Control ROD See FigsCheck Tire Pressure Primer OperationKnow Your Snow Thrower Ignition KEYMeets A.N.S.I. Safety Requirements Electric start button used for starting the engineTo USE Fuel SHUT-OFF Valve See Fig HOW to USE Your Snow ThrowerStopping To USE Choke Control See FigTo Throw Snow See Fig Using the CLEAN-OUT Tool See FigTo Move Forward and Backward See Fig Scraper BAR See Fig To Adjust Skid Plates See FigBefore Starting the Engine Check Engine OIL Level See FigBefore Stopping Snow Throwing TipsTo Start Engine If Recoil Starter has FrozenBefore Each USE MaintenanceGeneral Recommendations LubricationCleaning EngineChute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height Shear Bolts See FigTo Replace Belts See Fig Carburetor To Adjust Cable Tension See FigTo Remove Wheels See Fig Engine SpeedFuel System StorageOther Engine OILTroubleshooting Exploded KEY Part Description Auger Assembly RH Auger HousingAuger Assembly LH Scrapper BARSkid Plate LH Auger BearingBearing Plug Skid Plate RHDeflector Seal Chute WeldmentDeflector Weldment StrapCable Assembly Heat Shield LEVER/CABLE Rotator AssemblyCable Assembly Adjustable Rotator HeadLower Handle 196944X431 Panel Bracket LH 196943X431 Panel Bracket RHHandle Grip Pivot Support WeldmentKnob RED SpacerRetainer Handle KnobShifter ROD TOP Impeller RODTraction ROD Shifter ROD BottomInterlock CAM Console PanelInterlock Spring Torsion SpringRepair Parts Snow Thrower - Model Number MC624ES Drive Speed Selector AssemblyDrive Plate Assembly Rubber RingSprocket Axle ShaftRoll PIN 3/16 Clik PIN427963X428 Complete LCT EngineFrame Engine Mounting PlateIdler ARM Bracket Impeller BeltTraction Belt Idler Pulley432331X421 Wheel Assembly LH432332X421 Safety Ignition KEY 422663181037 DECAL, DangerService Notes Service Notes Limited Warranty
Top Page Image Contents