Bolens 2N1, 2P5 warranty Stopping the Engine, To Engage Augers, Engaging the Drive, This unit

Page 9

Recoil Starter

MPORTANT: Do not pull the starter handle with engine running.

WARNING: To avoid unsupervised engine operation, never leave the engine unattended while running. Turn the engine off after use and remove ignition key.

1.Insert ignition key fully into slot. Make sure it snaps into place. DO NOT turn ignition key. The engine cannot start unless the key is inserted into ignition switch.

2.Move throttle control to FAST (rabbit) position.

3.Move choke to the ON position (cold engine start). If engine is warm, place choke in OFF position.

4.Push primer three to five (3-5) times, making sure to cover vent hole when pushing. If engine is warm, push primer only once. Always cover vent hole when push- ing. Cool weather may require priming to be repeated.

5.Pull gently on the starter handle until it begins to resist, then pull quickly and forcefully to overcome the compression. Do not release the handle and allow it to snap back. Return rope SLOWLY to original position. If required, repeat this step.

6.As the engine warms, slowly rotate the choke control to OFF position. If the engine falters, restart engine and run with choke at half-choke position for a short period of time, and then slowly rotate the choke into OFF position.

Stopping the Engine

WARNING: To avoid unsupervised en- gine operation, never leave the engine unattended while running. Turn the engine off after use and remove ignition key

Run engine for a few minutes before stopping to help dry off any moisture on the engine.

1.Move throttle control to STOP position.

2.Remove the ignition key. Removing the key will reduce the possibility of unauthorized starting of the engine while equipment is not in use. Keep the key in a safe place. The engine cannot start without the ignition key.

3.Wipe all snow and moisture from the area around the engine as well as the area in and around the drive control and auger control. Also, engage and release both controls several times.

To Engage Augers

1.To engage the augers and start throwing snow, squeeze the auger control against the handle. Release to stop the augers.

Engaging the Drive

1.Lifting up on the handle will allow the rubber on the augers to propel the snow thrower forward. Pushing downward on the handle will raise the augers off the ground and stop forward motion.

NOTE: Excessive upward pressure on the handle will result in premature wear on the rubber auger blades which would not be covered by warranty.

2.Run the engine for a few minutes before stopping to help dry any moisture on the engine.

3.Clean the snow thrower thoroughly after each use.

5

Operation

WARNING

Muffler, engine and surrounding areas become hot and can cause a burn. Do not touch.

IMPORTANT:

For complete and detailed engine starting, stopping and storing instructions, it is recommended that you read the engine manual also included with

this unit.

NOTE:

Excessive upward pressure on the handle will result in premature wear on the rubber auger blades which would not be covered by warranty.

9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents 769-04201 OPERATOR’S ManualTable of Contents There are rotating blades inside Safety SymbolsDo not use the engine’s electric starter in the rain Your Responsibility Restrict the useTraining Safe Operation PracticesPreparation Your ResponsibilityOperation Maintenance & StorageDo not modify engine Average Useful LifeChute Assembly Snow Thrower SetupPositioning the Upper Handle Remove packing material, if presentKnow Your Snow Thrower Gas and Oil Fill-Up Before StartingTo Start Engine Electric Starter if so equippedStopping the Engine Clean the snow thrower thoroughly after each useTo Engage Augers Engaging the DriveShave Plate Adjustments MaintenanceReplacing Shave Plate Control CableLubrication EngineReplacing Auger Paddles Idler Pulley Belt Keeper To remove, pull belt hereTrouble Shooting 12.08.06 Warranty321 Models/Modèles 2N1 & 2P5Illustrated Parts Pièces Détachés Adressez-vous au «Service après-vente»3941 4546 31A-2N12P52 Page Page 06.08.12 GarantieDépannage Entretien Réglages Peut L’huile Côte de Vue Tirée est reurTarières les engager Pour Transmission lla engager PourLanceur à Démarreur Moteur du ArrêtMoteur du marche en Mise ’huile et d’essence PleinsDémarrage le Avant Souffleuse votre Connaître Et machine la arrêterApprenez .servir en vous de avant Supérieur guidon le Positionnez Goulotte la de InstallationResponsabilité Votre Remisage et EntretienMoyenne utile vie de Durée Gaz de émissions les concernant AvisFormation PréparationVotre MentMachine la d’utiliser Sécurité de SymbolesAu vente-après service du agent un Appelez Vente-après service au d’abord adresser vous sansTation Instructions les toutes comprendre bien de assurer vous04201-769 ’UTILISATION Notice

2P5, 2N1 specifications

The Bolens 2N1,2P5 is a versatile lawn care machine engineered for both homeowners and professionals seeking reliability and efficiency. This model combines a range of features designed for optimal performance in landscaping, gardening, and maintenance.

A notable characteristic of the Bolens 2N1,2P5 is its robust engine, which provides the power needed for various lawn care tasks. The engine is built with durability in mind, ensuring that it can handle challenging terrains and heavy workloads without sacrificing performance. This increased power translates into enhanced cutting capacity, enabling users to effortlessly tackle tall grass and thick weeds.

The design of the Bolens 2N1,2P5 is another key feature that sets it apart from competitors. Its ergonomic handle ensures comfort during extended use, reducing fatigue and enhancing the user experience. Adjustable height settings allow the operator to customize the cutting height to suit individual lawn styles and personal preferences. This flexibility makes it ideal for various grass types and seasonal conditions.

In terms of technology, the Bolens 2N1,2P5 boasts a dual-purpose functionality, allowing it to be used as both a mower and a mulcher. This versatility enables users to switch between cutting and mulching modes with ease, promoting greater efficiency in yard maintenance. The mulching capability not only recycles grass clippings back into the lawn, enriching the soil with nutrients, but also eliminates the need for bagging and disposal.

The machine's construction is reinforced with high-quality materials, ensuring weather resistance and longevity. This aspect is especially crucial for outdoor equipment that must endure exposure to various elements over time.

Safety features are also integrated into the design of the Bolens 2N1,2P5, including blade brakes and secure start mechanisms to protect the user during operation. These elements are designed to enhance safety without compromising on performance, making this model a reliable choice for all skill levels.

In conclusion, the Bolens 2N1,2P5 is a powerful, efficient, and user-friendly lawn care solution. With its robust engine, ergonomic design, dual-purpose functionality, and commitment to safety, it stands as an attractive option for anyone looking to maintain their outdoor space effectively.
Top Page Image Contents