Meade LX200 R instruction manual QUICK-START Guide

Page 4

QUICK-START GUIDE

It is recommended that you attach the supplied tripod to the LX200R for observing. Perform the telescope and AutoStar

IIsetup indoors in the light so that you become familiar with the parts and operation before moving the telescope out- side into the dark for observing. The setup is the same for the standard field tripod and the giant field tripod.

Remove the spreader bar (see above figure) from the shipping carton. Slide the spreader bar onto the threaded rod. Slide the rod through the tripod base. Position the spreader bar so that its three arms line up with the three tripod legs.

Threaded

Rod“C” Clip

Tripod Base

in slot

1.Remove the field tripod from the shipping carton. Stand the tripod vertically with the tripod feet down and with the tripod still fully collapsed. Grasp two of the tripod legs and, with the full weight of the tripod on the third leg, gently pull the legs apart to a fully open position.

4.Place the "C" clip into the slot in the threaded rod above the tripod head—this clip holds the thread- ed rod in place.

Tension

Knob

2.Thread in two lock-knobs on each leg (six total) near the foot of each tripod leg. Use the lock- knobs to vary the height of the inner, extendible tripod leg sections. Tighten the locks to a firm feel only; do not overtighten.

Slide rod through Tripod base

Line up with leg

Spreader Bar

3.Remove the threaded rod from the tripod head. A small piece of plastic holds the threaded rod in place. Remove the small plastic bag that is stapled to the threaded rod. This bag contains the "C" clip retainer and an extra clip.

5.Take the LX200R from its packaging and place the entire telescope onto the top of the tripod head, inserting the threaded rod into the central hole in the bottom of the drive base of the telescope. Tighten the tension knob (see above figure) to a firm feel only; firm tightening of the tension knob is sufficient to result in rigid positioning of the tripod legs.

Battery

Compartment

6.Remove the covers of the battery compartments located on the fork arms (one on each fork arm) and carefully lift the battery holders from their compart- ments, being mindful of the connector wires. Insert four (user-supplied) C-cell batteries into each bat- tery holder, oriented as shown on the diagram on the battery holder. Return the battery holders to their respective compartments. Replace the covers when you are done.

- 4 -

Looking at or near the Sun will cause irreversible damage to your eye. Do not point this telescope

 

at or near the Sun. Do not look through the telescope as it is moving.

Page 3 Page 5
Image 4
Page 3 Page 5
Contents Page Page Contents QUICK-START Guide Important Note Telescope Features AutoStarAscension Declination setting See Optional ACCESSORIES, pages 43, 44,# Computer Control Panel see inset Ascension, DefinitionsShift Microfocuser? Tour the Cosmos with Just the Push of a Button Autostar II FeaturesLibrary # of Objects Want to learn more about changing slew LX200R Tips How to Attach the Tripod to the Telescope Assembly Parts ListingGetting Started To install batteries How to Assemble Your TelescopeTip Attach Diagonal or accessories Choosing an EyepieceMounting and Adjusting the Viewfinder Too Much Power?Observing Using AutoStar IIs Arrow Keys ObservingObserving by Moving the Telescope Manually Terrestrial ObservingFocusing the Eyepiece Using the Microfocuser Slew SpeedsTo use the microfocuser Key # SpeedObserve the Moon Astronomical ObservingTo Track an Object Automatically Moving Through AutoStar II’s MenusWhich One’s the Alignment Star? It is recommended that you do not attempt a GPS fix indoorsUsing the Guided Tour Observe a Star using the Automatic Tracking FeatureGo To Saturn Detecting True Level Global Positioning SystemFinding True North AutoStar II Navigation Exercise Basic AutostarTo Calculate Sunset time Navigating AutoStar Look into the FutureMenus At orTo slew the telescope to catalog objects Object MenuWant to learn more about Observing Satellites? See Event Menu DefinitionUtilities Menu Glossary MenuLandmarks? See Mount Feature? See Appendix I Smart Setup MenuTiming is Everything Custom Tracking Rate Setup Menu Daylight SAVING, Adding and editing sites?Hot Button Menus To Add a Site to the user-defined site list Adding Observing SitesTo Edit a Site Creating User Objects To GO to a user-entered objectObserving Satellites LandmarksTo Add a landmark to the database TipsIdentify To Select a landmark from the databaseTo perform a Landmark Survey To check on the available amount of memory in AutoStarBrowse Displayed information ExampleAlternate Alt/Az Alignments How to perform the Easy Align ProcedureEasy Two-Star Alignment Two-Star Alt/Az Alignment One-Star Alt/Az AlignmentTo Set the Home Position Manually Tip Try a Spiral SearchPeriodic Error Correction Update Menu OptionTrain Menu Option Erase Menu OptionPhotography Few tips on photography with the LX200R telescopesPhotography with a Digital Camera Photography with Meade’s AutoStar SuiteStar Charts Image of M13 captured with the Deep Sky ImagerOptional Accessories Meade Series 4000 EyepiecesSeries 4000 8 24mm Zoom Eyepiece Illuminated Reticle Eyepiece Maintenance CollimationDefocused star images. Misaligned 1, 2, Aligned Meade Consumer Solutions Service What is Smart Drive?Inspecting the Optics Gauging the Movement of the Telescope10 LX200R Specifications Specifications10 f/10 LX200R Specifications 12 f/10 LX200R Specifications 14 f/10 LX200R SpecificationsAutoStar II System Specifications 16 f/10 LX200R SpecificationsAutoStar II Handbox Specifications Equatorial Alignment Setting CirclesCelestial Coordinates Declination Setting Circle Equatorial WedgeLining Up with the Celestial Pole Locating PolarisPrecise Polar Alignment LX200R mounted on an equa- torial wedgeAutoStar II Polar Alignment Easy Polar AlignmentOne-Star Polar Alignment Two-Star Polar AlignmentAppendix B Latitude Chart Latitude Chart for Major Cities of the WorldCity State/Prov./Country Latitude City Country LatitudeCommand Line What you will needTour Modes Comment LineWriting a Tour TitlePick ONE / Pick END Pick END Auto Slew on / Auto Slew OFF Downloading ToursAppendix D Training the Drive Further StudyTo observe the Apollo 15 landing site using the Moon option Appendix E the Moon MenuControl Panel Features 16 LX200R Unique FeaturesCommercial Shipping Telescope Assembly To Assemble the 16 Super Field TripodAttaching the 16 Drive Base Mounting the Optical Tube Assembly OTAAttaching the Fork Attaching the Power and Data Cords Observing Considerations14 LX200R Unique Features Appendix H To attach the microfocuser to the de-rotaterAppendix IntroductionOperation TrainingUpdate Permanently Mounted ScopesOther Menus Options Save As and Load OffBasic Astronomy AutoStar II GlossaryObjects in Space MoonPlanets Deep-Sky ObjectsPage Page Meade Limited Warranty

LX200 R specifications

The Meade LX200 R is a renowned telescope that has captivated astronomers and enthusiasts alike with its impressive blend of advanced technology, user-friendly features, and excellent optical performance. Launched as part of Meade's line of enjoyable yet high-performing telescopes, the LX200 R remains a top choice for both amateur stargazers and serious astrophotographers.

At the heart of the LX200 R is its advanced telescope design. It features a robust, 8-inch primary mirror, which provides exceptional light-gathering capability. This larger aperture allows users to observe faint celestial objects, including distant galaxies, nebulae, and star clusters, with stunning clarity and detail. The telescope's reflective optics are coated with high-quality, anti-reflective coatings that enhance contrast and minimize light loss, ensuring crisp, clear images even in challenging viewing conditions.

One of the standout features of the LX200 R series is its sophisticated computer-controlled GoTo mount. This feature allows users to locate over 30,000 celestial objects with remarkable precision using a simple one-button operation. The dual-axis motor drives enable smooth tracking of objects across the night sky, making it easier to follow their movements. The mount also includes an integrated GPS system, which automatically adjusts the telescope's location and time settings for accurate alignment without requiring complex manual adjustments.

The LX200 R is configured for both visual observations and astrophotography, accommodating a wide range of accessories like cameras and focal reducers. Its sturdy construction minimizes vibrations, which is crucial for capturing sharp images during extended exposures. Additionally, the telescope's optical tube is designed to be both lightweight and durable, making it convenient for transport and setup in various observing locations.

The ergonomic design of the LX200 R also enhances user experience, featuring a comfortable eyepiece height and an intuitive control panel. The display is user-friendly, allowing even novice astronomers to navigate settings and options quickly. With its combination of high-quality optics, advanced tracking capabilities, and versatile design, the Meade LX200 R continues to be a preferred choice for anyone looking to explore the wonders of the universe with sophistication and ease.
Top Page Image Contents