Orion 7338 Photography with the Deluxe 100mm f/6, Calculating Magnification Power

Page 3

Linear

 

Focus tension

bearing

 

thumbscrew

10:1 fine

Left coarsefocus knob

focus knob

Right coarse focus knob

Figure 2: Focuser detail

track the motion of the night sky accurately enough and long- exposure photography will be difficult, if not impossible.

The Deluxe 100mm f/6 comes without accessories. To set up and use the guidescope for use as a guidescope you will need the following:

2 Guide scope tube rings

1 Guide scope tube ring mounting plate

1Illuminated reticle eyepiece or Autoguider

1Diagonal (optional)

First, adjust the guidescope in the guidescope tube rings so that it is as parallel with the main optical tube. This may involve some large adjustments to the guidescope alignment thumb- screws. Loosen and tighten the alignment thumbscrews as needed to adjust the direction of the guidescope.

Once you have centered the object you wish to photograph, you will need to center the guidescope on a bright star near the object being photographed. Look in the illuminated reticle eyepiece (with the reticle turned on) and select a star that is in the field of view. To center the star, loosen one guidescope alignment thumbscrew and tighten another until the star is centered in the reticle. Check again to make certain that the object you wish to photograph is still centered in its field of view. If it is not, you will have to start the process over again.

Once you begin exposure you will make any adjustments nec- essary so that the guide star remains centered in the reticle of the illuminated eyepiece.

Photography with the Deluxe 100mm f/6

The Deluxe 100mm f/6 refractor makes a very capable astro- graph for your CCD or DSLR camera. With an optional camera adapter, the Deluxe 100mm f/6 becomes a 600mm f/6 tele- photo lens for a single-lens reflex camera. For long-distance terrestrial or astronomical photography, you need a T-ring for your particular camera model and a camera adapter. A 2" prime focus camera adapter is suggested to obtain the best focal distance for this optical tube. Simply attach the T-ring

to the camera body and thread the 2" prime focus camera adapter into the T-ring. Insert the barrel of the camera adapter into the 2" eyepiece holder on the focuser. Use the camera’s viewfinder to frame the picture. Use the telescope’s focuser to focus the image. Tighten the focus tension thumbscrew to make sure the camera does not slip out of focus.

Most CCD cameras will have a 1.25" or 2" barrel ready to attach directly to your telescope like an eyepiece or diagonal. No adapter is required, simply insert the barrel of the CCD camera into the 1.25" or 2" eyepiece holder and secure the camera with the silver thumbscrew lock.

The Deluxe 100mm f/6 Refractors were designed to reach focus with both DSLR and CCD cameras. However, every camera focus point is a little different. Depending on your camera, you may need to use an extension tube for your particular imaging setup. Any imaging accessory, such as a color filter wheel increases the amount of inward focus travel required. Before attaching any extra imaging accessory, try reaching focus first with the camera directly attached to the focuser, then see if you have enough focus travel left for extra accessories.

Imaging equipment is sometimes heavier than a diagonal and eyepiece. The dual-speed Crayford focuser is capable of handling the weight of your CCD or DSLR camera. Adding tension to the focuser drawtube will increase the amount of weight the focuser can handle. Install your camera onto the 2" or 1.25" adapter on the focuser during the day. Check the focuser for any slippage. If the focuser drawtube slides under the weight of the camera, you will need to add more tension to the focuser.

You may want to consider using a remote shutter release instead of the shutter release on the camera. Touching the camera can vibrate the system and blur the resulting photo- graphic image. Also, be sure to use a solid tripod.

Attaching the Deluxe 100mm f/6 to a Tripod or Mount

The Deluxe 100mm f/6 can be attached to a tripod or mount by the use of the pre-installed 1/4"-20 mounting block. The 1/4"-20 shaft of a sturdy camera tripod will thread into the hole on the mounting block on the underside of the optical tube (Figure 1).

Optional tube rings can also be used to mount the 100mm f/6 to attach it to an equatorial mount. Tube rings with an inner diameter of 100mm (3.9"), such as Orion item #7371, are needed. If you are using tube rings, you should first attach them to your telescope mount or dovetail bar and then lay the optical tube in the tube rings. You will need to extend the dew shield in order to accommodate tube rings on each side of the ¼"-20 mounting block.

Calculating Magnification (Power)

It is desirable to have a range of eyepieces of different focal lengths, to allow viewing over a range of magnifications. To calculate the magnification, or power, of a telescope, simply

3

Image 3
Contents #7338 S t r u c t i o n M a n u a lUse of Optional Eyepieces, Diagonal, and Finder Scope Using as a GuidescopeGetting Started Optical UseCalculating Magnification Power Photography with the Deluxe 100mm f/6Attaching the Deluxe 100mm f/6 to a Tripod or Mount Orion Telescopes & Binoculars OrionTelescopes.com One-Year Limited WarrantyCare & Maintenance Specifications