Care and Maintenance, Specifications, Cleaning Lenses

possible to take pictures of bright objects. Certain photo- graphic aids, such as the Orion SteadyPix, can help in taking photos by the afocal method.

6. Care and Maintenance

If you give your telescope reasonable care, it will last a life- time. Store it in a clean, dry, dust-free place, safe from rapid changes in temperature and humidity. Do not store the tele- scope outdoors, although storage in a garage or shed is OK. Small components like eyepieces and other accessories should be kept in a protective box or storage case. Keep the cap on the front of the telescope when it is not in use.

The telescope requires very little mechanical maintenance. The optical tube is steel and has a smooth painted finish that is fairly scratch-resistant. If a scratch does appear on the tube, it will not harm the telescope. Smudges on the tube can be wiped off with a soft cloth and a household cleaning fluid.

Cleaning Lenses

Any quality optical lens cleaning tissue and optical lens clean- ing fluid specifically designed for multi-coated optics can be used to clean the exposed lenses of your eyepieces or find- er scope. Never use regular glass cleaner or cleaning fluid designed for eyeglasses. Before cleaning with fluid and tissue, however, blow any loose particles off the lens with a blower bulb or compressed air. Then apply some cleaning fluid to a tissue, never directly on the optics. Wipe the lens gently in a circular motion, then remove any excess fluid with a fresh lens tissue. Oily fingerprints and smudges may be removed using this method. Use caution; rubbing too hard may scratch the lens. On larger lenses, clean only a small area at a time, using a fresh lens tissue on each area. Never reuse tissues.

Cleaning Mirrors

You should not have to clean the telescope’s mirrors very often; normally once every few years or so. Covering the tele- scope with the dust cover when it is not in use will prevent dust from accumulating on the mirrors. Improper cleaning can scratch mirror coatings, so the fewer times you have to clean the mirrors, the better. Small specks of dust or flecks of paint have virtually no adverse effect on the visual performance of the telescope.

The large primary mirror and the elliptical secondary mirror of your telescope are front-surface aluminized and over-coated with hard silicon dioxide, which prevents the aluminum from oxidizing. These coatings normally last through many years of use before requiring re-coating (which is easily done).

To clean the secondary mirror, you will need to remove it from the telescope. Before doing so, orient the telescope tube hori- zontally so that nothing accidentally falls down and hits the primary mirror. Hold the secondary mirror holder stationary while loosening and removing the center Phillips-head screw. Handle the mirror by its holder; do not touch the mirror surface itself. Once the mirror (still in its holder) is removed from the tube, follow the same procedure described below for cleaning

the primary mirror. You do not need to remove the secondary mirror from its holder when cleaning.

To clean the primary mirror, you must carefully remove the mirror cell from the telescope. To do this, remove the six screws on the side of the tube near the primary mirror cell. You do not need to remove the collimation screws on the bot- tom of the mirror cell. Remove the mirror cell from the tube. You will notice the primary mirror is held down with three clips fastened by two screws each. Loosen the screws and remove the clips.

You may now remove the mirror from the mirror cell. Do not touch the surface of the mirror with your fingers; lift it carefully by the edge. Set the mirror, aluminized face up, on a clean, soft towel. Fill a clean sink free of abrasive cleanser with room-temperature water, a few drops of liquid dishwashing detergent, and if possible a capful of 100% isopropyl alco- hol. Submerge the mirror (aluminized face up) in the water and let it soak for a few minutes (or hours if it’s a very dirty mirror). Wipe the mirror under water with clean cotton balls, using extremely light pressure and stroking in a straight line across the mirror. Use one ball for each wipe across the mir- ror. Then rinse the mirror under a stream of lukewarm water. Any particles on the surface can be swabbed gently with a series of cotton balls, each used just one time. Dry the mirror in a stream of air (a “blower bulb” works great), or remove any stray drops of water with the corner of a paper towel. Water will run off a clean surface. Cover the mirror surface with a tis- sue, and leave the mirror in a warm area until it is completely dry before reassembling the telescope.

7. Specifications

Primary mirror: 305mm diameter, 1500mm focal length, BK7 optical glass

Focal ratio: f/4.9

Focuser: Rack-and-pinion. accepts 2" and 1.25" eyepieces with included adapter, collimatible

Optical tube material: Rolled steel

Eyepieces: 25mm & 10mm Sirius Plössls, multi-coated, 1.25" barrel diameter

Eyepiece magnifications: 60x (25mm) and 150x (10mm)

Finder scope: 9x power, 50mm aperture, achromat, cross-hair, 5° field of view

Finder scope bracket: Dovetail base, spring-loaded X-Y alignment

Eyepiece rack: Holds three 1.25" eyepieces and one 2" eyepiece

Mirror coatings: Aluminum with SiO2 overcoat

Minor axis of secondary mirror: 70mm

Optical tube weight: 50 lbs.

Base weight: 33 lbs.

Tube length: 58"

Tube outer diameter: 14"