Orion 10134 XTBg, 10135 XT10g, 10135XT12g, #10134 XT8g instruction manual Shaft Spring

Page 7

Shaft

Spring

Figure 13. Place the three springs on the exposed threaded shafts of the mirror cell.

Figure 14. Lower the rear end ring onto the mirror cell so that the threaded shafts pass through the end ring, and the end ring rests on the springs.

Collimation knob

Nylon washer

Figure 15. Thread the collimation knobs, with nylon washers attached, through the rear end ring and onto the threaded shafts. Make sure the knobs have at least three full turns of engagement on the shafts.

ing the six Phillips-head screws that connect the end ring to the tube (Figure 12), and then pulling the end ring off the tube.

Figure 16. Locate the area of tube that is bulging out and preventing the end ring from fully seating.

Warning: Once the rear end ring is removed from the tube, the raw edge of the tube itself will be exposed. Be careful not to cut or otherwise hurt yourself on the tubeís edge. Also, be careful not to pinch your fingers when re- attaching the assembled mirror cell onto the tube.

2.Next, assemble the rear end ring to the mirror cell. Find a clean, flat surface, and turn the mirror cell over so that the mirror is facing downwards. Place the three springs onto the three exposed threaded shafts (Figure 13). Lower the end ring onto the mirror cell so the threaded shafts pass through it, and the end ring rests on the springs (Figure 14). Add a nylon washer to each collimation knob and thread the collimation knobs through the end ring and onto the threaded shafts (Figure 15). Make sure the knobs have at least three full turns of engagement on the shafts. The mirror cell is now ready to be installed onto the lower tube section.

3.Assembling the end ring back onto the tube can be a bit tricky. This is because the large diameter and thin alumi- num of the tube will cause the tube to become somewhat out of round once the end ring is removed. To assemble the rear end ring (with mirror and mirror cell now con- nected) to the tube, stand the tube up vertically so the raw edge of the tube is facing upwards. Line up the threaded holes in the edge of the mirror cell end ring with the holes in the end of the tube. Then, lower the entire mirror cell assembly onto the tube. There may be a bulge in the perimeter of the tube which prevents the mirror cell from fully seating onto the tube (Figure 16). Press against this bulge, and the entire mirror cell should seat onto the tube. Now, replace the six Phillips-head screws that connect the rear end ring to the tube.

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Orion SkyQuest XTg GoTo Dobsonians Overview of SkyQuest XTg Dobsonian 12 shown Parts List Table of ContentsUnpacking Base hardware for SkyQuest XTg Box #2 Dobsonian Base Refer to Figures 3Assembly of the Dobsonian Base AssemblyAssembly of the Optical Tube XT12g Only Shaft Spring Operating the EZ Finder Connecting the Optical Tube to Dobsonian BaseAccessory Installation EZ FinderUsing Eyepieces Replacing the BatteryAligning the EZ Finder GoTo Hand Controller Dual Purpose buttons Setup for AutoTracking or GoTo ModeSetup for AutoTracking or GoTo Mode Scroll ButtonsAlignment for GoTo Operation Using the Telescope AutoTracking ModeBrightest Star Alignment Two-Star Alignment SW 235SEPointing Accuracy Enhancement PAE Using the Telescope in GoTo ModeObject Database in the Hand Controller Selecting an ObjectUtility Functions Other FunctionsTracking Setup FunctionsPage Identifying an Unknown Object Using the User Defined DatabaseSaving an object to the database Recalling a user-defined objectUpdating the GoTo Hand Controller’s Firmware Disconnecting from the ComputerPreparing the Computer for the Update Linking with a ComputerAligning the Secondary Mirror Collimating the Optical SystemCollimation Cap and Mirror Center Mark Preparing the Telescope for CollimatingAligning the Primary Mirror Using Your TelescopeStar-Testing the Telescope Focusing the Telescope1200mm = 42x 28mm Viewing with EyeglassesAiming/Pointing the Telescope MagnificationAstronomical Observing Moon Astronomical ObjectsCleaning Eyepiece Lenses Care and MaintenanceCleaning Mirrors SkyQuest XT8g SpecificationsSkyQuest XT10g SkyQuest XT12g Menu Tree Appendix a Time Zones of the World Appendix B RS-232 Connection Additional RS-232 Commands Sending a Tracking RateSending a Slow-GoTo Command Resetting the Position of Azimuth or AltitudeStar Charts Page Page Page Page Page Page Page Page One-Year Limited Warranty

10135 XT10g, 10134 XTBg, 10135XT12g, #10134 XT8g specifications

The Orion #10134 XT8g, #10135 XT12g, #10134 XTBg, and #10135 XT10g are exceptional choices in the realm of computerized telescopes, catering to both novice stargazers and seasoned astronomers. These models are designed for easy use while delivering stellar performance and high-quality optics.

At the heart of these telescopes is the high-quality optics that Orion is renowned for. Each model features a primary mirror made from durable glass, enhanced with a parabolic shape to minimize optical distortions and improve light gathering capabilities. The XT8g and XT10g utilize an 8-inch and 10-inch mirror, respectively, while the XT12g boasts a large 12-inch aperture, providing users with deeper views of celestial phenomena. The larger the aperture, the more light the telescope can collect, revealing fainter objects in the night sky.

In terms of technology, the "g" designation signifies that these telescopes are equipped with Orion’s innovative GoTo system. This advanced motorized mount enables users to easily locate and track celestial objects with the push of a button, making the stargazing experience more enjoyable and accessible. The system includes a database of thousands of celestial objects, allowing users to explore the universe with ease.

The XTg models also come with an intuitive hand controller that features a user-friendly interface for navigating the night sky. Additionally, the telescopes can be controlled via a smartphone or tablet, providing flexibility for tech-savvy users who prefer modern conveniences.

Durability and stability are crucial in any telescope, and the XT series does not disappoint. Each model is constructed on a robust and stable base, designed to minimize vibrations and provide a steady view, even at higher magnifications. This stability ensures that amateur astronomers can enjoy detailed views, from the craters of the moon to the rings of Saturn and beyond.

Each telescope comes with a cradle-style altazimuth mount for easier adjustments and tracking capabilities. The included eyepieces allow for various magnifications, enhancing the viewing experience and enabling observers to appreciate the beauty of the cosmos.

In summary, the Orion XT series, including the #10134 XT8g, #10135 XT12g, #10134 XTBg, and #10135 XT10g, stands out for their exceptional optics, innovative GoTo technology, robust build quality, and user-friendly operation. These telescopes are ideal for anyone wishing to explore the wonders of the night sky, making them a worthy investment for years of astronomical discovery.
Top Page Image Contents