Intel GS-SR195V manual Federal Communications Commission FCC Statement

Page 5

Safety Information

*To reduce the risk of fire, use only No. 26 AWG or larger telecommunications line cord.

*Do not plug a modem or telephone cable into the network interface controller (NIC) receptacle.

*Disconnect the modem cable before opening a product enclosure, touching or installing internal components, or touching an uninsulated modem cable or jack.

*Do not use a telephone line to report a gas leak while you are in the vicinity of the leak.

Federal Communications Commission (FCC) Statement

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

Properly shielded and grounded cables and connectors must be used in order to meet FCC emission limits. Neither the provider nor the manufacturer are responsible for any radio or television interference caused by using other than recommended cables and connectors or by unauthorized changes or modifications to this equipment. Unauthorized changes or modifications could void the user's authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1)this device may not cause harmful interference, and

(2)this device must accept any interference received, including interference that may cause undesired operation.

FCC part 68 (applicable to products fitted with USA modems)

The modem complies with Part 68 of the FCC Rules. On this equipment is a label that contains, among other information, the FCC registration number and Ringer Equivalence Number (REN) for this equipment. You must, upon request, provide this information to your telephone company.

If your telephone equipment causes harm to the telephone network, the Telephone Company may discontinue your service temporarily. If possible, they will notify in advance. But, if advance notice is not practical, you will be notified as soon as possible. You will be informed of your right to file a complaint with the FCC.

5

Image 5
Contents System Installation Guide Table of Content Security Server Precaution for Product with Laser Devices Safety, Care and Regulatory InformationImportant safety information FCC part 68 applicable to products fitted with USA modems Federal Communications Commission FCC StatementCanadian Department of Communications Compliance Statement Page Introduction Contents PackagesProcessor Supported Features SummaryFront Panel Safety Regulations Step System Hardware InstallationChassis Removal and Installation Pin1 indicator CPU InstallationMemory Installation Heat Sink InstallationPCI Expansion Card Installation FAN Duct Removal and Installation Hard Disk Drive InstallationZCR Installation and Removal Optional Device Front View of GS-SR195V Appearance of GS-SR195VRear View of GS-SR195V HDD ID BTN&LED Switch and LED Indicators IntroductionLAN LED Description Connector Icon Description GA-9IVDPC Motherboard Layout Motherboard Layout & Jumper SettingCPU DDR A2 CPU1 DDR B2 2 Supported DDR333 Dimm Populations DDR Dimm Slot Population1 Supported DDR266 Dimm Populations Clrcmos Clear Cmos Function Jumper SettingBiostbl Cmos Lock Function Bioswp Bios Werite Protect Function Controlkeys Bios SetupBoot Status Page Setup Menu / Option Page Setup MenuMainMenu MainSystem Date System TimeBit I/O SystemInformation About This Section Advanced AdvancedEmbeddedVideoController PCI ConfigurationOnboard VGA Control EmbeddedSCSIControllerOnboard LAN Control EmbeddedNIC Gbit #1Legacy USB Support Advanced Chipset ControlUSB Controller Data Parity Error Recovery Force Compliance ModePCI-E portA Device PCI-E port A1 DeviceWake On LAN MemoryFrequencyMachine Checking Advanced Processor OptionHyper Threading Technology Adjacent Cache Line Prefetch Thermal ManagermentSet Max Ext Cpuid = NX ProtectionSerial Port a Peripheral ConfigurationFloppy disk controller Serial Port BFloppy Check Parallel ATASerial ATA Reset ConfigurationDataNativeModeOperation Clk Gen Spread SpectrumClear Case Open Log Extended MemoryTestingNetwork Server Voltage Vcore 1&2/ 3.3V/ +12V / 1.5V CPU 1&2/ System/ W83792d 1/2/3 TemperatureHardware Monitor About This Section Security Set Supervisor PasswordPassword on boot Set User PasswordConsole Redirection ServerBaud Rate Com PortAddressConsole Type FlowControlHaltOn Clear Mem. ECC Error InfoFatal Error on portA Boot Device Priority About This Section BootAbout This Section Exit ExitExit Discarding Changes Load SettupDefaultExit Saving Changes Save Changes Discard ChangesAcronyms AppendixIoapic

GS-SR195V specifications

The Intel GS-SR195V is a powerful processor designed primarily for embedded systems and industrial applications. It leverages Intel's advanced architecture to deliver high-performance computing in a compact form factor. This processor is notable for its ability to handle complex tasks while maintaining energy efficiency, making it ideal for applications in robotics, IoT devices, and complex machinery.

One of the main features of the GS-SR195V is its multi-core architecture. With up to four cores, the processor is capable of executing multiple threads simultaneously, improving overall performance in parallel processing tasks. This makes it particularly beneficial in environments where multitasking is essential, such as in automation and control systems. The cores also support Intel Hyper-Threading technology, allowing for more efficient use of resources by enabling each core to handle two threads at once.

In addition to its robust processing capabilities, the GS-SR195V integrates advanced graphics processing features. Its integrated Intel HD Graphics allows for smooth rendering of visuals without the need for a dedicated graphics card. This is particularly advantageous in applications requiring visual interfaces or monitoring systems, where high-quality graphics output is a necessity.

The processor also includes support for Intel's security technologies, such as Intel Trusted Execution Technology (TXT) and Intel Software Guard Extensions (SGX). These features enhance data protection and help ensure secure operation in sensitive environments, thereby instilling confidence in users regarding data integrity and system security.

Energy efficiency is a cornerstone of the GS-SR195V's design. With a low thermal design power (TDP), it operates effectively in various thermal environments, reducing the need for intensive cooling solutions. This allows for smaller and more compact system designs, leading to cost savings and increased reliability.

The GS-SR195V is equipped with a range of connectivity options, supporting various interfaces such as USB, Ethernet, and serial communication, making it versatile for integration into existing systems. This flexibility enables developers to design solutions that meet specific application needs without extensive modifications.

In conclusion, the Intel GS-SR195V stands out as a highly capable processor for embedded applications, thanks to its robust performance, energy efficiency, and advanced security features. Its combination of multi-core processing, integrated graphics, and versatile connectivity makes it an ideal choice for businesses looking to implement powerful computing solutions in industrial and IoT environments.