Eiki LC-NB4 owner manual Basic Operation, Turning on / OFF Projector, Turning on Projector

Page 19

BASIC OPERATION

TURNING ON / OFF PROJECTOR

TURNING ON PROJECTOR

1

Complete peripheral connections (with Computer, VCR, etc.)

 

before turning on projector. (Refer to "CONNECTING

 

PROJECTOR" on pages 11~13 for connecting the equipment.)

2

Connect the projector's AC Power Cord into an AC outlet. LAMP

 

Indicator lights RED, and READY Indicator lights GREEN.

 

NOTE : When “On start” function is ON, this projector is turned

 

on automatically by connecting AC Power Cord to an

 

AC outlet. (Refer to pages 35, 36.)

3

Press POWER ON-OFF button on Top Control or on Remote

 

Control Unit to ON. LAMP Indicator dims, and Cooling Fans

start to operate. Preparation Display appears on a screen and the count-down starts. The signal from PC or Video source appears after 30 seconds.

30

Preparation Display disappears after 30 seconds.

TURNING OFF PROJECTOR

1

Press POWER ON-OFF button on Top Control or on Remote

 

Control Unit, and a message "Power off?" appears on a screen.

2

Press POWER ON-OFF button again to turn off the projector.

 

LAMP Indicator lights bright and READY Indicator turns off.

 

After the projector is turned off, Cooling Fans operate (for 90

 

seconds). During this "Cooling Down" period, this appliance

 

cannot be turned on.

3

When projector has cooled down, READY Indicator lights

 

GREEN again and you can turn the projector on. After cooling

down completely, disconnect AC Power Cord.

TO MAINTAIN THE LIFE OF LAMP, ONCE YOU TURN PROJECTOR ON, WAIT AT LEAST 5 MINUTES BEFORE TURNING IT OFF.

Power off?

Message disappears after 4 seconds.

When “Power Management” function is ON, projector detects signal interruption and turns off Projection Lamp automatically. Refer to “Power management” on pages 36.

When WARNING TEMP. Indicator flashes red, the projector is automatically turned off. Wait at least 5 minutes before turning on the projector again.

When WARNING TEMP. Indicator continues to flash, follow procedures below:

1.Press POWER ON-OFF button to turn a projector off and disconnect AC Power Cord from an AC outlet.

2.Check Air Filters for dust accumulation.

3.Clean Air Filters. (See "AIR FILTER CARE AND CLEANING" section on page 40.)

4.Turn the projector on again.

If WARNING TEMP. Indicator should still continue to flash, contact the sales dealer where you purchased this projector or service center.

19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents
Model LC-NB4 To the Owner Voor de klanten in Nederland Safety InstructionsFederal Communication Commission Notice CompliancesTable of Contents Compact Design Keystone Correction Features and DesignName of Each Part of Projector PreparationHOT AIR Exhausted Connecting AC Power Cord SETTING-UP ProjectorFor Continental Europe Preparation Positioning Projector Adjustable FeetRoom Light Preparation Moving Projector Terminal Input Jack Connecting ProjectorTerminals of Projector Video Input JackTerminals Projector Connecting to ComputerTerminals Connecting to Video EquipmentBefore Operation Operation of Remote Control UnitLaser Pointer Function Remote Control Batteries Installation Lamp Replace Indicator TOP Controls and IndicatorsOperating ON-SCREEN Menu HOW to Operate ON-SCREEN MenuFlow of ON-SCREEN Menu Operation Guide Window Before Operation Menu BARSound Menu Turning OFF Projector Basic OperationTurning on / OFF Projector Turning on ProjectorPicture Freeze Function Adjusting ScreenZoom Adjustment Keystone AdjustmentDirect Operation Sound AdjustmentTimer Function Basic Operation No Show FunctionAuto Computer InputSelecting Input Source Selecting Computer SystemFreq Computer Input Compatible Computer SpecificationsResolution ResolutionAuto PC Adj PC AdjustmentAuto PC Adjustment PC Adjust MenuComputer Input Manual PC Adjustment Display area H Display areaFull screen Image 1~4 Picture Image AdjustmentsImage Level Select Direct Image Level Select MenuImage Adjust Menu Computer Input Image Level AdjustmentScreen Menu Picture Screen AdjustmentVideo Video InputVideo AV System Menu Video or S-VIDEO Component Video Signal FormatSelecting Video System PAL / Secam / Ntsc / NTSC4.43 / PAL-M / PAL-NCinema Sharpness Video Input Image Level AdjustmentColor TintProvides image at a normal video aspect ratio of 4 Setting Menu SettingSetting Menu To change the code of Projector To change the code of the Remote Control UnitAppendix Lamp ReplacementLamp Replace Appendix Lamp Replace Counter Lamp Handling PrecautionsInstallation Operating Wireless MouseOperating Wireless Mouse Recommendation MaintenanceAIR Filter Care and Cleaning Cleaning Projection LensTroubleshooting Function does not Remote Control UnitWireless Mouse Does not workTechnical Specifications Monitor OUT Terminal Analog Appendix Configurations of TerminalsDVI-I Terminal DIGITAL/ANALOG POA-MCMAC Control Port ConnectorOptional Parts POA-MCSRLPage Page Key to better communications Canada