Eiki LC-SM4 owner manual Basic Operation, Turning on / OFF Projector, Turning on Projector

Page 19

BASIC OPERATION

TURNING ON / OFF PROJECTOR

TURNING ON PROJECTOR

1

Complete peripheral connections (with Computer, VCR, etc.)

before turning on projector. (Refer to "CONNECTING

 

PROJECTOR" on pages 11~13 for connecting the equipment.)

2

Connect the projector's AC Power Cord into an AC outlet. LAMP

Indicator lights RED, and READY Indicator lights GREEN.

3

Press POWER ON-OFF button on Top Control or on Remote

Control Unit to ON. LAMP Indicator dims, and Cooling Fans

start to operate. Preparation Display appears on a screen and the count-down starts. The signal from PC or Video source appears after 30 seconds.

30

Preparation Display disappears after 30 seconds.

TURNING OFF PROJECTOR

1

Press POWER ON-OFF button on Top Control or on Remote

Control Unit, and a message "Power off?" appears on a screen.

2

Press POWER ON-OFF button again to turn off the projector.

LAMP Indicator lights bright and READY Indicator turns off.

 

After projector is turned off, Cooling Fans operate (for 90

 

seconds). During this "Cooling Down" period, the projector

 

cannot be turned on.

3

When projector has cooled down, READY Indicator lights

GREEN again and you can turn projector on. After cooling down

completely, disconnect AC Power Cord.

TO MAINTAIN THE LIFE OF LAMP, ONCE YOU TURN PROJECTOR ON, WAIT AT LEAST 5 MINUTES BEFORE TURNING IT OFF.

Power off?

Message disappears after 4 seconds.

When “Power Management” function is ON, projector detects signal interruption and turns off Projection Lamp automatically. Refer to “Power management” on page 36.

When WARNING TEMP. Indicator flashes red, projector is automatically turned off. Wait at least 5 minutes before turning on projector again.

When WARNING TEMP. Indicator continues to flash, follow procedures below:

1.Press POWER ON-OFF button to turn the projector off and disconnect AC Power Cord from an AC outlet.

2.Check Air Filters for dust accumulation.

3.Clean Air Filters. (See "AIR FILTER CARE AND CLEANING" section on page 39.)

4.Turn the projector on again.

If WARNING TEMP. Indicator should still continue to flash, contact the sales dealer where you purchased this projector or service center.

19

Image 19
Contents Model LC-SM4 To the Owner Voor de klanten in Nederland Safety InstructionsFederal Communication Commission Notice CompliancesTable of Contents Compact Design One-Touch Auto PC Adjustment Features and DesignName of Each Part of Projector PreparationHOT AIR Exhausted Connecting AC Power Cord SETTING-UP ProjectorFor Continental Europe Preparation Positioning Projector Adjustable FeetRoom Light Preparation Moving Projector Audio Computer Connecting ProjectorUSB Connector Series B Terminals of ProjectorTerminals Projector Connecting to ComputerAudio Video Connecting to Video EquipmentBefore Operation Operation of Remote Control UnitBattery Remote Control Battery InstallationBefore Operation Operating Range Image Button TOP Controls and IndicatorsOperating ON-SCREEN Menu HOW to Operate ON-SCREEN MenuFlow of ON-SCREEN Menu Operation Screen Menu Before Operation Menu BARTurning OFF Projector Basic OperationTurning on / OFF Projector Turning on ProjectorKeystone Adjustment Adjusting ScreenZoom Adjustment Focus AdjustmentDirect Operation Sound AdjustmentTimer Function Basic Operation No Show FunctionSelect Computer System Manually Computer InputSelecting Input Source Selecting Computer SystemKHz Computer Input Compatible Computer SpecificationsResolution FreqAuto PC Adj PC AdjustmentAuto PC Adjustment PC Adjust MenuComputer Input Manual PC Adjustment Display area H Display areaFull screen Image Select Menu Picture Image AdjustmentImage Level Select Direct Image Level Select MenuImage Adjust Menu Computer Input Image Level AdjustmentScreen Menu Picture Screen AdjustmentVideo Video InputAV System Menu Component Video Selecting Video SystemAuto AV System Menu Video or S-VIDEOCinema Video Input Image Level Adjustment Provides image at a normal video aspect ratio of 4 Setting Menu SettingSetting Menu Lamp counter reset To change the code of the Remote Control UnitPower management Remote controlAppendix Lamp ReplacementLamp Replace Appendix Lamp Replace Counter Lamp Handling PrecautionsRecommendation MaintenanceAIR Filter Care and Cleaning Cleaning Projection LensTroubleshooting Does not work Remote Control UnitTechnical Specifications Optional Parts Appendix Configurations of TerminalsControl Port Connector USB Connector Series BKey to better communications Canada