Eiki LC-SE10 Key registration, Deleting key registration, To lock the projector with USB key

Page 57

Appendix

USB Key Lock Function (This is optional function. Optionally supplied USB Key needed.)

By using optionally supplied Projector USB Key, operation of the projector can be restricted by the projector owner. Once the projector is locked with the USB Key, only the owner who has key can operate the projector.

Key registration

Before using the USB key, you must register USB key into the projector.

Turn the projector ON and connect the USB Key to the USB terminal located on the rear of the projector. (See Item u on page10)

A USB key icon (A) will appear on screen and the USB Key connected to the terminal will be automatically registered into the projector. (Do not disconnect the USB Key while the icon is displayed on screen.

If you like to have another USB key registered, follow the procedure below:

1)Connect first key to the USB terminal on the projector.

2)Press the Menu button and On-Screen Menu will appear. Press the Point Left/Right button to move the red frame pointer to the Setting menu icon.

3)Press the Point Down button to move the red frame pointer to the USB Key Lock icon, then press the SELECT button. USB Key Lock menu will appear.

4)Press the SELECT button again and USB Key registration menu (B) will appear.

5)Select "Registration" with Point Up/Down button and press the SELECT button. A USB key icon (C) will appear. For about 30 seconds while the USB key icon is on screen, remove the first registered USB Key from the projector and connect another USB Key which you wish to register as second key to the projector. After that, OK icon (D) will appear for a little while to make sure the USB Key is registered.

Up to two keys can be registered into the projector. If you attempt to register third key, an X mark (E) will be displayed to prohibit the registration.

Deleting key registration

With the USB Key plugged in, select "DELETE (USB plugged in)" from the USB Key registration menu (B) and press the SELECT button. OK icon will appear on screen and the registration will be cleared. If you select "Delete (Another)", the registration of another USB Key which is not connected to the projector will be cleared.

To lock the projector with USB key

1)Press the Menu button and On-Screen Menu will appear. Press the Point Left/Right button to move the frame pointer to the Setting menu icon.

2)Press the Point Down button to move the red frame pointer to the USB Key Lock icon, then press the SELECT button. USB Key Lock menu will appear

3)Press the Point Left/Right button and select one of the following key lock modes.

Off

Projector is not locked with USB Key.

 

 

On1

Need the USB Key every time the Projector is turned on.

On2 Need the USB Key to turn the Projector on after AC power cord is reconnected to the AC outlet.

USB Key lock

USB Key lock

Setting Menu icon

When the USB KEY LOCK is set, a

USB KEY mark will appear on the

MENU BAR.

Move the pointer to item and then press POINT LEFT/RIGHT button(s). (Off, On1 or On2)

When pressing the SELECT button at USB key lock, the USB key lock Menu appears.

(A)

 

(B)

(C)

(D)

(E)

When turning the projector ON again with the projector set to USB KEY LOCK On1 or On2 position, a screen indicating USB KEY LOCK will appear after the countdown. At that time, if the registered USB KEY is not inserted within 3 minutes, the automatically turned off.

Note:

After having inserted and certified the USB KEY, it can be removed from the projector without interrupting projector operation.

57

Page 56 Page 58
Image 57
Page 56 Page 58
Contents Model LC-SE10 Table of Contents Risk of Electric Shock Do not Open To the OwnerVoor de klanten in Nederland Safety InstructionsInstalling the Projector in Proper Position Safety InstructionsAir Circulation Moving the ProjectorFederal Communication Commission Notice ComplianceFor Continental Europe ComplianceFor the U.S.A. and Canada 200 240 V ACFeatures and Design Front Back Bottom Part Names and FunctionsTerminal Part Names and Functions1!2 TopZoom Freeze Remote ControlPointer Function Laser Pointer FunctionWireless Mouse Operation Remote Control CodeRemote Control Batteries Installation Remote Control Operating RangeInstallation Adjustable FeetPositioning the Projector Installation Connecting to a ComputerTerminals Projector Video Source example Connecting to Video EquipmentBasic Operation Turning On the ProjectorTurning Off the Projector Focus Adjustment Zoom AdjustmentKeystone Adjustment Basic OperationAuto Set Up Function Picture Freeze FunctionKeystone correction Corner Sound Adjustment Timer FunctionNo Show Function Direct OperationOn-Screen Menu Remote ControlTop Control On-Screen MenuMenu Bar Input Source Selection Computer InputComputer System Selection Computer InputAuto ModeComputer Adjustment Auto To store adjustment dataAuto PC Adj Computer Adjustment Manual Mode free ResetDisplay area To store adjustment data To clear adjustment dataStandard Image Level SelectionReal Image button Standard RealImage Level Adjustment Screen Size Adjustment Video Input Input Source Selection Video, S-Video, Y, Pb/Cb, Pr/CrPb/Cb, Pr/Cr Input Source Selection RGB Scart 21-Pin Video InputRGB Scart Input button Computer Video Computer 2 buttonVideo or S-Video Video System SelectionComponent AV System Menu Video or S-VideoImage button Standard Cinema CinemaColor TintProgressive Resets all adjustment to their previous figure Setting SettingSetting Lamp mode Power managementOn start PointerWireless Mouse mode To change the code for the remote controlProjector mode To change the code for the projectorMaintenance and Cleaning Projector is shut down and the Warning indicator lights redThen check the items below Cleaning the Air Filters Maintenance and CleaningCleaning the Projection Lens Cleaning the Projector CabinetReset the Lamp replace counter Lamp ReplacementLamp Replace Counter Lamp Handling PrecautionsAppendix TroubleshootingAppendix Projector Condition Indicators and Projector ConditionImage Adjust Screen PC AdjustMenu Tree InputImage Adjust System SettingImage Select SoundCompatible Computer Specifications FreqKHz Technical Specifications Configurations of Terminals Terminal HDB15-PIN Pin ConfigurationTerminal DVI-I Pin Configuration Optional Parts Attaching the Lens Cover Deleting key registration Key registrationTo lock the projector with USB key Off Projector is not locked with USB Key On1Appendix Appendix Key to better communications Canada

LC-SE10 specifications

The Eiki LC-SE10 is a versatile and high-performance LCD projector designed for both business and educational environments. This projector combines advanced technology with user-friendly features, making it an excellent choice for presentations, lectures, and multimedia applications.

One of the standout features of the Eiki LC-SE10 is its high brightness level, which typically ranges around 5,000 ANSI lumens. This ensures that images and videos remain clear and vibrant even in well-lit rooms. The projector boasts a native resolution of WUXGA (1920 x 1200), providing sharp and detailed images that enhance the viewing experience. This resolution is particularly beneficial for displaying high-definition content, making the Eiki LC-SE10 suitable for various applications, from video conferencing to educational lectures.

Another key characteristic of the Eiki LC-SE10 is its versatility in connectivity options. It comes equipped with multiple input ports, including HDMI, VGA, and USB, allowing users to easily connect various devices such as laptops, tablets, and media players. The projector also supports wireless connectivity, enabling seamless content sharing without the hassle of tangled cables. This feature is especially useful for collaborative environments where multiple users may need to present or share information.

The Eiki LC-SE10 incorporates advanced optical technologies, including a high-quality lens system that provides impressive throw distances and zoom capabilities. With a considerable optical zoom range, users can adjust the image size without having to reposition the projector, making it ideal for different room sizes and setups.

In addition to its performance and connectivity features, the Eiki LC-SE10 is designed for ease of use and maintenance. It incorporates a lamp life of up to 10,000 hours in eco mode, reducing the need for frequent lamp replacements and lowering overall operating costs. The projector also includes a built-in filter to keep the internal components free from dust, ensuring longevity and consistent performance.

In terms of portability, the Eiki LC-SE10 is relatively compact and lightweight, making it easy to transport between locations. Whether for a classroom setting or boardroom presentation, the projector's durability and reliability make it a preferred choice for professionals and educators alike. Overall, the Eiki LC-SE10 combines cutting-edge technology, versatility, and ease of use, making it a powerful tool for any presentation or teaching environment.
Top Page Image Contents