Eiki LC-SX4L Connecting Projector, Terminals of Projector, Replacement of Terminal

Page 11

CONNECTING PROJECTOR

TERMINALS OF PROJECTOR

This projector applies various input/output terminals and 3 terminal slots for expansion to tune to diversity of signals from computers and video equipment. 3-built-in Terminal Slots enable you to arrange desired combinations of input sources just by changing Terminal Boards. For Terminal Boards, contact sales dealer where you purchased a projector.

NOTE; DVI Terminal can not be used INPUT 3 slot.

3 TERMINAL SLOTS (Factory set)

		DVI			AUDIO		CONTROL PORT
		DVI			R	L
					R	L
						(MONO)
R/Pr	G/Y	B/Pb	H/HV	V		AUDIO	CONTROL PORT
R/Pr	G/Y	B/Pb	H/HV	V	R	L
					R	L
						(MONO)
VIDEO/Y	C		S-VIDEO		AUDIO
VIDEO/Y	C				R	L
					R	L
						(MONO)
SERIAL PORT IN		SERIAL PORT OUT			AUDIO OUT		USB
SERIAL PORT IN		SERIAL PORT OUT					USB
R/C JACK					R	L
R/C JACK
RESET						(MONO)

INPUT/OUTPUT

TERMINALS

INPUT 3 INPUT 2 INPUT 1

DVI Terminal

5 BNC Terminal

AV Terminal

REPLACEMENT OF TERMINAL

1

2

Remove 2 Screws on terminal.

Pull out terminal by holding handle.

3	Replace terminal. Insert terminal along Guide to fit Plug
	into Socket.
4	Tighten screws to secure terminal.	Screws

Guide

Socket

Plug

Figure shows HDB 15-PIN terminal (Optional parts).

11

Image 11

Contents Multimedia Projector Model LC-SX4LTo the Owner Voor de klanten in Nederland Safety InstructionsFederal Communication Commission Notice CompliancesTable of Contents Compatibility Features and DesignName of Each Part of Projector PreparationFor U.S.A. and Canada For Continental Europe SETTING-UP ProjectorConnecting AC Power Cord Positioning Projector Preparation Lens InstallationLens Shift Adjustment Moving Projector Preparation Picture Level and Tilt AdjustmentTerminals of Projector Connecting ProjectorReplacement of Terminal Input 1, 2 Connecting Projector INPUT/OUTPUT Terminals and Jacks InputAudio Output Jacks Terminals of a Projector Connecting to Computer2INPUT Terminals of a Projector Connecting to Video EquipmentBefore Operation TOP Controls and IndicatorsLaser Pointer Function Operation of Remote ControlRemote Control Batteries Installation Flow of ON-SCREEN Menu Operation HOW to Operate ON-SCREEN MenuOperating ON-SCREEN Menu Screen Menu Before Operation Menu BARTurning OFF Projector Basic OperationTurning on / OFF Projector Turning on ProjectorKeystone Adjustment Adjusting ScreenFocus Adjustment No Show Function Timer FunctionBasic Operation Picture Freeze Function Sound Menu Sound AdjustmentDirect Operation Menu OperationInput Computer InputSelecting Input Source Selecting Computer SystemPC System Menu Computer Input Automatic MULTI-SCAN SystemSelect Computer System Manually AutoResolution Computer Input Compatible Computer SpecificationsComputer Input PC AdjustmentAuto PC Adjustment PC Adjust MenuComputer Input Manual PC Adjustment Full screen Display areaDisplay area H Image Select Menu Picture Image AdjustmentImage Level Select Direct Image Level Select MenuImage Adjust Menu Computer Input Image Level AdjustmentScreen Menu Picture Screen AdjustmentVideo Input When Select Input 3 AV TerminalAV System Menu Video or S-VIDEO Selecting Video SystemVideo Input AutoCinema Noise reduction Video Input Image Level AdjustmentColor TintProvides image at a normal video aspect ratio of 4 Setting Menu SettingSetting Menu To change code of Projector To change code of Remote Control UnitLamp counter reset Wireless Mouse modeProjector mode Operating Wireless Mouse Operating Wireless MouseMaintenance InstallationCleaning Projection Lens Appendix AIR Filter Care and CleaningYellow Lamp Dim Lamp Red Lamp Mark on Lamp Appendix Lamp ManagementOrder Replacement Lamp Appendix Lamp ReplacementTroubleshooting Function does not Remote Control UnitWireless Mouse Does not workTechnical Specifications DVI-I Terminal DIGITAL/ANALOG Appendix Configurations of TerminalsUSB Port Terminal Appendix Key to better communications Canada