Intel PMB-601LF user manual PNP/PCI Configuration Setup Screen, Init Display First

Page 70

Chapter 4 Award BIOS Setup

4-8. PNP/PCI CONFIGURATION

Choose PNP/PCI CONFIGURATIONfrom the main menu, a display will be shown on screen as below:

Phoenix - AwardBIOS CMOS Setup Utility

PnP/PCI Configurations

Init Display First

[PCI Slot]

Item Help

Reset Configuration Data

[Disabled]

 

Resources Controlled By

[Auto (ESCD)]

Menu Level ►

 

x IRQ Resources

Press Enter

 

PCI/VGA Palette Snoop

[Disabled]

 

** PCI Express relative items **

 

Maximum Payload Size

[128]

 

 

 

 

↑↓→←: Move Enter: Select

+/-/PU/PD:Value F10:Save ESC:Exit F1:General Help

F5: Previous Values

F6: Fail-Safe Defaults F7:Optimized Defaults

 

 

 

PNP/PCI Configuration Setup Screen

The PNP/PCI Configuration Setup describes how to configure PCI bus system. PCI, also known as Personal Computer Interconnect, is a system, which allows I/O devices to operate at speeds nearing the speed of the CPU itself uses when communicating with its own special components.

This section covers technical items, which is strongly recommended for experienced users only.

INIT DISPLAY FIRST:

This item allows you to decide to active whether PCI Slot or on-chip VGA first.

RESET CONFIGURATION DATA:

Normally, you leave this field Disabled. Select Enabled to reset Extended System Configuration Data (ESCD) when you exit Setup if you have installed a new add-on and the system configuration has caused such a serious conflict that the operating system cannot boot.

PMB-601LF USERS MANUAL

Page: 4-21

Image 70
Contents USER’S Manual PMB-601LF Intel Core 2 Duo FCC Notice Table of Contents Appendix Expansion BUS Introduction Hardware Configuration About this ManualSystem Specifications CPU mPGA775Sata Interface Irda Port Safety Precautions Hardware Jumper & Connector Quick Reference Table PMB-601LF Connector, Jumper and Component locations Component LocationsHOW to SET the Jumpers Jumpers and CapsJumper Diagrams Jumper SettingsPIN Assignment COM Port ConnectorRS-232 RS-422 RS-485 COM3DCD# Selection Jumper Settings Illustration COM3 RI & Voltage SelectionCOM4 RI & Voltage Selection Jumper Settings Function Pin closed Illustrations COMKeyboard and PS/2 Mouse Connector Reset ConnectorExternal Speaker Connector Hard Disk Drive LED ConnectorATX Power Button PIN Assignment SpkvccKeylock Connector Pled ConnectorExternal SMI Connector Function Jumper Setting CPU FAN ConnectorClear Cmos Data Selection Power FAN Connector System FAN ConnectorNB FAN Connector VGA Connector SATA1 PIN Assignment Serial ATA ConnectorSATA2 PIN Assignment SATA3 PIN Assignment SATA4 PIN AssignmentFloppy Disk Drive Connector Printer Connector Universal Serial BUS Connector Irda Connector USB&LAN Connector LAN21MDIP0 ATX Power Connector Line-Out Sound ConnectorLine-In Mic-InMemory Installation CD AUDIO-IN ConnectorDram Bank Configuration Dimm DIMM3 DIMM4 Total Memory Software Utilities Introduction Filename Purpose Assume that CD ROM drive is DInstallation of VGA Driver VGA Driver UtilityFlash Bios Update System Bios UpdatePage3-5 LAN Driver Utility IntroductionInstallation Procedure for Windows 2000/XP/2003 Sound Driver UtilityIntel Chipset Software Installation Utility Installation of Utility for Windows 2000/XP/2003USB2.0 Software Installation Utility Installation of Utility for Windows 2000/XPWatchdog Timer Configuration Configuration SequencePage3-11 Award Bios Setup Introduction Entering Setup Setup program initial screenDate Standard Cmos FeaturesCmos Setup screen TimeSata Channel 0/1/2/3/4/5 Halt on Drive aVideo Base MemoryHard Disk Attributes Award Hard Disk Type TableAdvanced Bios Features Bios Features Setup ScreenLimit Cpuid Maxval CPU FeatureExecute Disable BIT Vitrualization TechnologyBoot UP Floppy Seek Hard Disk Boot PriorityFIRST/SECOND/ THIRD/ Other Boot Device Typematic Rate SettingTypematic Rate CHARS/SEC Typematic Delay MsecApic Mode Security OptionChipset Features Setup Screen Advanced Chipset FeaturesDram Timeing Selectable CAS Latency Time Dram RAS# to CAS# DelayDvmt Mode Dram RAS# Precharge TimeIntegrated Peripherals Integrated Peripherals Setup ScreenDVMT/FIXED Memory Size Onchip IDE Device IDE HDD Block ModeIDE DMA Transter Access Primary MASTER/SLAVE PIO Secondary MASTER/SLAVE PIOSuper IO Device USB Device Setting Onboard Serial Port 3/4 Serial Port 3/4 USE IRQUSB Mouse Function USB 1.0 ControllerUSB Keyboard Function USB Flash DiskPower Management Setup Screen Power Management SetupAcpi Function Resume by Alarm Power ManagementSuspend Mode SOFT-OFF by PWR-BTTNReset Configuration Data PNP/PCI ConfigurationPNP/PCI Configuration Setup Screen Init Display FirstIRQ-n Assigned to Resource Controlled byIRQ Resources PCI/VGA Palette SnoopCPU/SYSTEM/POWER FAN Shutdown TemperatureSYSTEM/CPU Temperature PC Health StatusAuto Detect DIMM/PCI CLK Frequency / Voltage Control Setup ScreenFREQUENCY/VOLTAGE Control Spread SpectrumLoad FAIL-SAFE Defaults Load Optimized DefaultsTo SET a Password Password SettingTo Disable the Password Save & Exit Setup Exit Without Saving Expansion BUS PCI BUS PIN Assignment Technical Summary Block Diagram Interrupt MAP IRQ AssignmentRTC & Cmos RAM MAP Code AssignmentTimer Channel Map Assignment Timer & DMA Channels MAPDMA Channel Map Assignment Memory Map Memory MAPMap

PMB-601LF specifications

The Intel PMB-601LF is a versatile and powerful multimedia processor designed primarily for automotive applications. Leveraging Intel's advanced technology expertise, the PMB-601LF brings together high-performance computing capabilities with energy efficiency, making it a pivotal component in modern automotive systems, such as infotainment and telematics.

One of the standout features of the PMB-601LF is its robust processing architecture, which typically includes multiple cores capable of executing concurrent tasks. This multi-core design ensures smooth operation of complex applications, enabling real-time processing for user interfaces, navigation systems, and advanced driver-assistance systems (ADAS). With its support for high-definition video playback and multi-channel audio output, the PMB-601LF enhances the in-car experience by delivering rich multimedia content.

In terms of connectivity, the Intel PMB-601LF is equipped with various interfaces, including USB, Ethernet, and CAN bus, allowing seamless integration with a wide range of automotive sensors and external devices. This connectivity is essential for modern vehicles that rely on extensive data exchange between different subsystems and the cloud.

Another significant characteristic of this processor is its energy efficiency. Designed to meet the stringent power consumption requirements of automotive applications, the PMB-601LF operates effectively within the limited power budgets often present in vehicles. Its ability to maintain high performance while minimizing power draw is crucial for optimizing overall vehicle energy consumption, especially in electric and hybrid models.

The PMB-601LF also incorporates advanced security features, which are becoming increasingly important in the age of connected vehicles. By integrating hardware-level security protocols, the processor helps protect against potential vulnerabilities and cyber threats, ensuring the safety and integrity of vehicle systems and data.

Furthermore, Intel's investment in software compatibility and support for various operating systems provides developers with the tools they need to create and customize applications tailored to specific consumer needs. The flexibility of the PMB-601LF facilitates the development of innovative solutions that enhance vehicle functionality and user experiences.

In summary, the Intel PMB-601LF is a powerful multimedia and automotive processor that combines high performance, energy efficiency, robust connectivity, and advanced security features. As the automotive industry continues to evolve towards more connected and autonomous vehicles, the PMB-601LF is positioned as a critical enabler of the next generation of automotive technologies, ultimately improving the driving experience and advancing automotive innovation.