Intel MI910F user manual Power LED Pins 11 Pin # Signal Name

Page 22

INSTALLATIONS

Power LED: Pins 11 - 15

Pin #

Signal Name

11	Power LED
12	No connect
13	Ground
14	No connect
15	Ground

ATX Power ON Switch: Pins 7 and 17

This 2-pin connector is an “ATX Power Supply On/Off Switch” on the system that connects to the power switch on the case. When pressed, the power switch will force the system to power on. When pressed again, it will force the system to power off.

Reset Switch: Pins 9 and 19

The reset switch allows the user to reset the system without turning the main power switch off and then on again. Orientation is not required when making a connection to this header.

Hard Disk Drive LED Connector: Pins 10 and 20

This connector connects to the hard drive activity LED on control panel. This LED will flash when the HDD is being accessed.

	Pin #			Signal Name
	10			HDD Active
	20			5V

18	MI910 User’s Manual

Image 22

Contents Intel CoreTM 2 Duo Celeron GM965 VersionAcknowledgments Table of Contents MI910 Mini ITX Motherboard Introduction Product DescriptionChecklist MI910 Specifications CPU FSBBoard Dimensions Installations Installing the CPU Installing the Memory LockSetting the Jumpers Jumper Locations on MI910 JP9 PCI/PCIE Riser Card Selection JP5 LCD Panel Power SelectionJBAT1 Clear Cmos Setting JP8 CompactFlash Slave/Master SelectionConnectors on MI910 Connector Locations on MI910 MI910 Solder Side CN1 PS/2 Keyboard and PS/2 Mouse Connectors CN2, CN3 COM1 and VGA ConnectorFAN2 CPU Fan Power Connector IDE1 IDE Connector FDD1 Floppy Drive ConnectorATX1 ATX Power Supply Connector J1 Fpanel System Function ConnectorPower LED Pins 11 Pin # Signal Name FUSB1 USB0/USB1 Connector COM2J7 Mini PCI Connector CN8, CN9 Sata Connectors J3, J4 Lvds Connectors 1st channel, 2nd channelJ5 LCD Backlight Connector J2 COM2 Serial PortJ12 Front Audio Connector J10 SPI Flash Connector factory use onlyJ11 1394 Connector J8 Digital I/OJ14 IrDA Connector SDVOCCLK+ SdvocclkHeaders and Connectors on MI910 Daughter Cards JP4RED ID391 J2 DVI Connector This page is intentionally left blank Bios Setup Bios Introduction Bios SetupPhoenix AwardBIOS Cmos Setup Utility Standard Cmos Setup DateIDE Channel Master/Slave TimeDrive a / Drive B Video Halt OnHard Disk Boot Priority Advanced Bios FeaturesCPU Feature Virus WarningBoot Other Device Quick Power On Self TestFirst/Second/Third Boot Device Boot Up Floppy SeekSecurity Option Typematic Delay MsecApic Mode MPS Version Control for OSSystem Bios Cacheable Advanced Chipset FeaturesMemory Hole At 15M-16M Panel Scaling On-Chip VGA SettingPanel Number Integrated Peripherals OnChip IDE DeviceOn-chip Primary/Secondary PCI IDE IDE HDD Block ModeOn-chip Primary PCI IDE Enabled IDE Primary/Secondary Master/Slave PIOKB Power on Password On-Chip Serial ATA SettingPower on Function Hot Key Power onPwron After PWR-Fail Uart Mode SelectOnboard Serial Port USB 1.0 ControllerPower Management Power Management SetupRUN Vgabios if S3 Resume Acpi FunctionPower On by Ring Suspend ModeHDD Power Down Video Off MethodResume by Alarm Reload Global Timer EventsPNP/PCI Configurations Shutdown Temperature CPU Warning TemperatureTemperatures/Voltages 1st 2st Smart Fan TemperatureAuto Detect PCI Clk Frequency/Voltage ControlSpread Spectrum Modulated Set Supervisor Password Load Fail-Safe DefaultsLoad Optimized Defaults Save & Exit SetupDrivers Installation Intel Chipset Software Installation Utility Click IntelR Chipset Software Installation UtilityDrivers Installation VGA Drivers Installation Click IntelR GM965Chipset Family Graphics DriverImportant Note AC97 Codec Audio Driver Installation Click Realtek AC97 Codec Audio DriverLAN Drivers Installation Click Install Base Software to continueDriver Installation Appendix O Port Address MapInterrupt Request Lines IRQ Level FunctionWatchdog Timer Configuration Sample CodeAppendix OutportbW627EHFINDEXPORT, W627EHFLOCK W627EHFLOCK