Intel Motherboard, SE400BX manual Error Messages, Setup

Page 58

Error Messages

Table 39. BIOS Error Messages (continued)

Error Message

Explanation

 

 

Fixed Disk 0 Failure or

Fixed disk is not working or not configured properly. Check to see if fixed

Fixed Disk 1 Failure or

disk is installed properly. Run Setup to be sure the fixed-disk type is

Fixed Disk Controller Failure

correctly identified.

 

 

Incorrect Drive A type - run

Type of diskette drive for drive A not correctly identified in Setup.

SETUP

 

 

 

Invalid NVRAM media type

Problem with NVRAM (CMOS) access.

 

 

Keyboard controller error

The keyboard controller failed test. Try replacing the keyboard.

 

 

Keyboard error

Keyboard not working.

 

 

Keyboard error nn

BIOS discovered a stuck key and displayed the scan code nn for the stuck

 

key.

 

 

Keyboard locked - Unlock key

Unlock the system to proceed.

switch

 

 

 

Monitor type does not match

Monitor type not correctly identified in Setup.

CMOS - Run SETUP

 

 

 

Operating system not found

Operating system cannot be located on either drive A or drive C. Enter

 

Setup and see if fixed disk and drive A are properly identified.

 

 

Parity Check 1

Parity error found in the system bus. BIOS attempts to locate the address

 

and display it on the screen. If it cannot locate the address, it displays

 

????.

 

 

Parity Check 2

Parity error found in the I/O bus. BIOS attempts to locate the address and

 

display it on the screen. If it cannot locate the address, it displays ????.

 

 

Press <F1> to resume, <F2> to

Displayed after any recoverable error message. Press <F1> to start the

Setup

boot process or <F2> to enter Setup and change any settings.

 

 

Real time clock error

Real-time clock fails BIOS test. May require motherboard repair.

 

 

Shadow RAM Failed at offset:

Shadow RAM failed at offset nnnn of the 64 KB block at which the error

nnnn

was detected.

 

 

System battery is dead -

The CMOS clock battery indicator shows the battery is dead. Replace the

Replace and run SETUP

battery and run Setup to reconfigure the system.

 

 

System cache error - Cache

RAM cache failed the BIOS test. BIOS disabled the cache.

disabled

 

 

 

System CMOS checksum bad -

System CMOS RAM has been corrupted or modified incorrectly, perhaps

run SETUP

by an application program that changes data stored in CMOS. Run Setup

 

and reconfigure the system either by getting the default values and/or

 

making your own selections.

 

 

System RAM Failed at offset:

System RAM failed at offset nnnn of the 64 KB block at which the error

nnnn

was detected.

 

 

System timer error

The timer test failed. Requires repair of system motherboard.

 

 

nnnn = hexadecimal number

58

Image 58
Contents SE440BX Revision History Revision Revision History DateContents Using the Setup Program ContentsRegulatory and Integration Information SE440BX Motherboard Product GuideContents Motherboard Features Features SummaryMotherboard Features ComponentsBack Panel I/O Connectors Back Panel I/O ConnectorsMain Memory Microprocessor UpgradesMicroprocessor Second Level Cache MemoryReal-Time Clock Input/Output I/O ControllerUniversal Serial Bus USB Support Bios Upgrades PCI Auto ConfigurationExpansion Slots IDE Auto ConfigurationSecurity Passwords ISA Plug and Play CapabilityAdvanced Power Management APM Power ManagementBattery Advanced Configuration and Power Interface AcpiHardware Monitor Optional Wake on RingWake on LAN Technology Optional Audio Subsystem OptionalCrystal Semiconductor CS4236B Audio Codec Audio ConnectorsSpeaker Optional Crystal Semiconductor CS4611 PCI Audio AcceleratorInstalling and Replacing Motherboard Components Before You BeginHow to Install a Processor How to Install and Remove the MotherboardInstalling and Replacing Motherboard Components Install the Retention Mechanism Installing the Processor Retention MechanismInstall the Processor Installing the ProcessorHow to Set the Processor Speed Installing the Heatsink Support Top BarJ8A1 How to Upgrade to a Boxed Pentium II Processor Remove the Installed ProcessorRemoving the Heatsink Support Top Bar and the Processor Removing the Heatsink Support Retention Pins Remove the Heatsink Support BaseUsing the Heatsink Support Base Removal Tool Upgrade the Processor How to Install MemoryDimm Size Non-ECC Configuration Shows the location of the Dimm sockets How to Remove Memory Installing a DimmHow to Replace the Battery VarningReplacing the Battery How to Clear the Passwords Jumper Settings for Setup Program Modes Using the Setup ProgramSetup Program Modes Mode Jumper DescriptionSetup Function Keys Setup MenusSetup Menu Bar Function KeysMain Menu Maintenance MenuMain Menu Advanced Menu No defaultAuto default Advanced MenuPeripheral Configuration Submenu Peripheral Configuration SubmenuIDE Configuration IDE ConfigurationStandard default IDE Configuration SubmenusIDE Configuration Submenus CD-ROMFloppy Options Video Configuration SubmenuDMI Event Logging Available default Reserved Resource Configuration SubmenuResource Configuration Submenu Security MenuPower Menu Power MenuBoot Menu Boot Menu∙ Atapi CD-ROM Hard Drive SubmenuHard Drive Submenu Options DescriptionRemovable Devices Submenu Feature DescriptionExit Menu Removable Devices SubmenuObtaining the Bios Upgrade File Upgrading the BiosPreparing for the Upgrade Recording the Current Bios SettingsCreating the Bios Upgrade Diskette Upgrading the BiosCreating a Bootable Diskette Upgrading the BiosRecovering the Bios Changing the Bios Language Technical Reference Motherboard ConnectorsPC/PCI Fan 3 Connector Wake on Ring ConnectorWake on LAN Technology Connector Auxiliary Line In ConnectorFan 2 Connector CD Audio ConnectorChassis Intrusion Connector Fan 1 ConnectorScsi LED Connector Power Supply ConnectorPC/PCI Connector Front Panel Connectors Connector Pin Signal NameDMA Channels Motherboard ResourcesMemory Map Memory MapO Map MapAddress hex Size Description Interrupts PCI Configuration Space MapPCI Configuration Space Map InterruptsBios Error Messages Error MessagesBios Beep Codes Bios Error MessagesError Messages SetupRegulatory Compliance Safety RegulationsRegulatory and Integration Information EMC RegulationsProduct Certification Markings Installation PrecautionsInstallation Instructions Regulatory and Integration InformationEnsure Host Computer and Accessory Module Certifications Ensure Electromagnetic Compatibility EMCPlace Battery Marking on the Computer Prevent Power Supply OverloadUse Only for Intended Applications

Motherboard, SE400BX specifications

The Intel SE400BX is a high-performance motherboard designed primarily for demanding enterprise applications, delivering reliability and scalability for a wide range of business needs. This board is specifically tailored for use with Intel’s Pentium III and Celeron processors, providing a solid foundation for both server and workstation configurations.

One of its standout features is the support for Intel’s Slot 1 architecture, which allows for easy processor upgrades without the need for complex socket replacement. This flexibility is essential for businesses that require adaptability in their technology to keep pace with evolving workloads.

The SE400BX motherboard is equipped with a versatile Intel 440BX chipset, renowned for its stability and exceptional memory handling capabilities. This chipset supports up to 1GB of SDRAM using the DIMM standard, ensuring that your system has adequate memory bandwidth for multitasking and demanding applications. Additionally, it features dual-channel architecture, enhancing data flow and minimizing bottlenecks, which is critical for high-performance computing tasks.

Storage connectivity is another strong suit of the Intel SE400BX. The motherboard includes an ATA-66 interface, supporting both hard drives and optical devices. With up to four IDE connectors available, it allows for ample storage configuration options, enabling users to set up various RAID configurations for redundancy and increased data access speeds.

In terms of connectivity, the SE400BX offers integrated networking capabilities, including a built-in Ethernet controller, which simplifies installation and eliminates the need for a separate network card for basic networking tasks. This feature makes the motherboard an appealing choice for businesses looking to reduce components while maintaining solid networking performance.

On the expansion front, the motherboard provides three PCI slots, offering ample room for additional cards such as graphics cards, sound cards, or specialized expansion cards for specific business needs. This expandability ensures that businesses can tailor their systems to their own unique requirements without being constrained by the motherboard’s capabilities.

Overall, the Intel SE400BX combines powerful performance, reliability, and essential features that meet the demands of enterprise environments. Its strategic design and advanced technology make it a valuable addition to any business looking to build a robust computing infrastructure.