Cambridge Audio 340Razur user manual Troubleshooting, Technical specifications

Troubleshooting

A low hum or buzz sound can be heard

Power cords or lighting placed near this product.

Analog inputs not connected securely.

Sound is not audible from one channel

Speaker connections disconnected.

Speaker set to ‘None’ in OSD setup menu.

Sound cuts off when listening to music or there is no sound even though power is ON

Speaker impedance is less than prescribed for the 340R. The unit is not adequately ventilated and may be overheating.

Low bass or “phasey” response

Speaker polarity (+/-) of one or more speakers is reversed.

An unusual hissing noise is heard when listening to a radio broadcast in stereo, but not heard when listening in mono

A slight noise may be heard because the method used for modulation of FM stereo broadcasts is different than that used for mono broadcasts.

Aerial quality also effects the level of hiss heard.

Noise is excessive in both stereo and monaural radio broadcasts

Poor location and/or direction of the antenna.

Transmitting station is too far away.

No sound from the rear speakers

Source being played is not recorded in surround sound. Speaker/s set to ‘None’ in OSD setup menu.

A stereo mode has been selected.

No sound from the centre speaker

Centre speaker has been set to ‘None’ in OSD setup menu. A stereo mode has been selected.

No sound from the subwoofer

Sub has been set to ‘Off’ in the OSD setup menu or via the remote.

DDPLII mode (which has no LFE channel) has been selected with all speakers set to ‘Large’.

Remote control is not working

The batteries are flat.

The remote is too far from the receiver or out of the effective range.

No sound from speakers when connected to a digital input

Audio input type is set to analogue (check display). Press the Audio Type button to switch to digital.

No sound from speakers when connected to an analogue input

Audio input type is set to digital. Press the Audio Type button to switch to analog (check display).

Audio input type can also be set in the Input Setup menu of the OSD.

OSD not visible

Check that the TV/Monitor is connected to the 340R and is using a Composite or S-Video connection.

For more frequently asked questions (FAQ’s), technical advice and information on getting the most out of your 340R, please visit the Support section on Cambridge Audio’s website:

www.cambridgeaudio.com/support.php

	azur	340R
Technical specifications
Power Output	80 watts rms per channel,		ENGLISH
	8 ohms, two channels driven
	50 watts rms per channel,
	8 ohms all 5 channels driven
THD	<0.006% @1kHz
Crosstalk	<-60dB
Frequency response	20Hz – 20kHz +/- 1dB
Audio Input Sensitivity	150mV
Audio Input Impedance	47kOhms
Digital Input Impedance	75ohms (Coaxial/SPDIF)
S/N Ratio	>90dB ‘A’ weighted
Tone Control Range	Bass +/- 10dB
	Treble +/- 10dB
FM Tuner	87.5-108MHz,
	75 ohm coaxial aerial
AM Tuner	522-1629kHz,
	300 ohm loop aerial
Video Levels /Impedance	Composite (CVBS) =
	1Vp-p / 75ohm
	S-Video (S-VHS) =
	Y 1Vp-p / 75ohm
	C 0.286 Vp-p / 75ohm
	Component =
	Y 1Vp-p / 75ohm
	Cb/Cr 0.75Vp-p / 75ohm
	Pb/Pr 0.75Vp-p / 75ohm
HDMI	Transfer of all resolutions up to and
	including 1080p @ 50/60Hz (1920 x
	1080) supported, with HDCP
	handshaking.
Architecture	CS42518 CODEC
	CS493263 DSP
Audio Inputs	6 Line Level + Tuner
	5.1 Direct input
Audio Outputs	5 Amplified Speaker outputs
	1 Subwoofer output
	1 Tape/MD/CDR record output
Video Inputs	3 Composite, 2 S-Video,
	2 Component Video, 2 HDMI
Video Ouputs	1 Composite, 1 S-Video,
	1 Component Video, 1 HDMI
Digital Inputs	4 Co-Axial, 4 Optical
Digital Outputs	1 Co-Axial, 1 Optical, 1 HDMI
Stby power consumption	<10w
Max power consumption	400w
Dimensions - H x W x D	150 x 350 x 430mm
Weight	8.9kg (19.6lbs)

21